How to Remove a 2015-2017 Nissan Juke Front Bumper Cover, Part 1/3

We're back at it again! This is our video for a front bumper cover removal for a 2015 Nissan Juke. It's just the removal of the bumper cover and not the installation, so it's a very short video.
Where To Buy: bit.ly/2015NissanJuke
00:00 Start
0:08 Pop open the hood
0:20 Tools needed
0:38 Remove the bottom bumper screws
1:46 Remove the fender trim and bolts underneath
3:30 Do the same on the opposite side
5:15 Remove the top bumper clips
5:54 Remove the front bumper
6:44 Unplug the fog lights
7:39 Outro
TOOLS NEEDED:
Flat-head screwdriver, Philips screwdriver, 10mm wrench or socket wrench and, or panel clip remover.
INSTRUCTIONS:
You want to remove the clips and (or push-pins) bolts from the bottom of the bumper. Of course, be sure not to lose any fasteners and put them in the same place you found them. Remove the push-pin from the fender well by using your screwdriver, or panel clip remover. This push-pin holds the fender molding in place. It's best to use the proper tool but the bumper is trash on this car, so we're using the flat-head. There is another plastic clip underneath the fender molding. Use your ratchet with a 10mm socket to remove the bolt under the molding that connects the front bumper to the fender. Repeat on the opposite side.
When removing the front bumper, firmly pull the bumper off the fender. The bumper clips onto a bracket attached to the fender. Be sure not to yank the bumper off because it may break the bracket. Next, remove the clips/bolts on the top of the bumper. This bumper was wedge in underneath the fog light, so we had to pry it out. Do not let the bumper drop, be sure to disconnect the fog lights. Most wire harness' will or electrical plugs require you to push down the tab for release. The Juke's particular plug requires you to pull the tab UP for release.
Source: www.revemoto.com
Follow Us on
FB: / revemoto
IG: / revemoto
________________________________________________________
#Nissan Juke #revemoto #paintedautoparts #Juke #highquality #DIY #HowTo
DISCLAIMER: While ReveMoto tries to make the information in this video as accurate as possible, we make no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself (DIY) projects entail some risk. It is the sole responsibility of the viewer to assume this risk. ReveMoto is not responsible or liable for any loss, damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@ReveMoto]

Thank you for watching our videos. We really hope it helped you out. Where To Buy: bit.ly/2015NissanJuke If you need any other painted auto parts, visit us at : www.revemoto.com

[@ProfRainestorm]

This is great I think you're gonna save me a lot of money replacing this myself. Hopefully I dont screw it up, Thanks!

[@ReveMoto]

This was our first Nissan Juke, so if we can do it, you can too! Please subscribe, it really helps us a lot. 🤘

[@johnnyr6391]

great job! very helpful video. Thanks.

[@ReveMoto]

Hello and thank you for watching!

[@Jmack6969]

Great video, very helpful

[@ReveMoto]

Glad you think so!

[@Roadsurfer2k11]

Thanks. To remove the grill will I have to do this bumper procedure? I want to repaint the grill. 2013 juke

[@ReveMoto]

Hello and yes. The grille is clipped on to the back. So you would have to at the very least loosen the top of the bumper to pop the grille off. Check out this video >> kzbin.info/www/bejne/faLTgplmnc-ompY

[@Roadsurfer2k11]

@@ReveMoto thanks, I got it 😁. Definitely had to pop the front bumper off its white corner clips to get to the grill corner tabs.

[@coltonceplina1702]

What is the last plug you unplugged? I just noticed I’m wired for that, but it’s just tucked up in there.

[@chrisb7551]

Nice video! Were you able to push that dent out or did you have to replace it??

[@ReveMoto]

Unfortunately not had to get a new part

[@Wanderrap]

I think you can also apply this to a 2012 model

[@ReveMoto]

We believe so, the model range, if we're not wrong is from 2012-2017. Thank you for watching!

[@Wanderrap]

@@ReveMoto great video nonetheless.Thanks for the step by step process.Helps me a lot!

[@brianslattery3249]

Good Vid BUT really you should buy yourself a set of Plastic removal tools to remove clips, screw drivers could cause damage. just saying.

[@ReveMoto]

Oh man i just got a set. My new videos feature them. Life changing tool

[@demigodtv1742]

rear bumper nissan juke you have vid tutorial?

[@ReveMoto]

Not at the moment, but hopefully we'll get another Juke in soon!

[@novaomsk]

Весь бампер теперь в засечках

[@ReveMoto]

Привет. Мы перевели ваш комментарий, но смогли отменить только "Весь бампер теперь в" Хорошего дня! Hello. We translated your comment but could only undestrand the "Весь бампер теперь в" Have nice day!