There's just something about a mechanic using an adjustable wrench backwards that gets on my nerves.
@Coastal_Cruzer2 жыл бұрын
Tf you mean backwards
@MR-bp3in2 жыл бұрын
The way he's using it is backwards. Spreads the jaws open
@tomwilson15842 жыл бұрын
Plumbers use adjustable wrenches, a good mechanc/technician, does'nt butcher nuts and bolts or tools in general.
@johnghatti54352 жыл бұрын
I’ve never had luck with that style extractor to begin with. The wrench being backwards doesn’t bother me that much though.
@tomwilson15842 жыл бұрын
@@johnghatti5435 there are many ways to remove broken studs etc, it all down to training and skill, drilling out and heli-coil being a popular method in the aero industry.
@MR-bp3in2 жыл бұрын
That actually works about 1 in a thousand lol. Usually the head pops off and you end up drilling it completely out
@julioperez-delgadojr29762 жыл бұрын
Thats happened to me so many times I dont even bother with those taps, they always break off in there and are as hard as a drill bit so drilling that out after is near impossible. Best to just drill the bolt through and pull the bits out with a pick or re-tap the thread if its messed up.
@crazyamericangamer70362 жыл бұрын
Yes drill it out
@brettwilson3592 жыл бұрын
No, it works about 700 out of a thousand. You just have to know what you're doing. Obviously, you don't.
@mike69322 жыл бұрын
This works "sometimes" Kinda need ideal conditions though. I've also ended up with a broken extractor. Drill the whole mess out and helicoil
@Dabbin9162 жыл бұрын
If it isn’t recessed like this one and you can get around the head of the screw I’ll pull out the grinder.
@voidjointx2 жыл бұрын
How did you get the extractor out?
@Bradamsmx52 жыл бұрын
Not a broken bolt. A stripped screw, yes. Those things almost never work on truly broken and recessed/flush screws. Best bet is a left hand drill bit.
@anything63982 жыл бұрын
There called easy outs . They are left handed .
@DigitalArtisan772 жыл бұрын
left hand drill bit would drill the same circular hole in the other direction no? Also not stripped, as he wound it out on the perfectly function threads. Rounded out would be the term.
@Bradamsmx52 жыл бұрын
@@DigitalArtisan77 Correct, it would drill a circular hole spinning in the opposite direction. The process of the left hand bit biting into the material is normally sufficient to break the screw loose. If it doesn’t, gradually increase size until you either remove the screw or you have removed enough threads to run a tap through it.
@Bradamsmx52 жыл бұрын
@@anything6398 Yes they are, and yes they are. Anyone who has ever attempted to use them in a recessed or flush screw will tell you, they seldom ever actually work. If the screw is still under pressure or is corroded, the action of the “Easy out” attempting to wedge its way into the remaining material of the screw actually causes the body of the screw to expand very slightly. This in turn wedges the screw into place even more. Making it ever more difficult to remove.
@anything63982 жыл бұрын
@@DigitalArtisan77 you would need an multiple drill bits left handed. Easy outs are cheaper than buying every size in drill bit that's all I mean. Your way is good too.👍💯👍
@JwsDirtShop2 жыл бұрын
This man needs a Nobel prize he's the first person to ever make that actually work. Lol
@codytjaden98472 жыл бұрын
These actually work all the time
@alexnagy19812 жыл бұрын
Square ones work much better
@sawedoff57452 жыл бұрын
These work great.
@jasonritter24922 жыл бұрын
In the engine building world we always get them to work right. You just got know how to use them..
@CallmeBaki2 жыл бұрын
@@jasonritter2492 I call bs these things suck 90% of the time iv been working on cars my hole life and these barely work right the square ones r better
@richardcoleman39302 жыл бұрын
I've worked on planes for 21 years, we've used these and the stubby 1/2" drive variant. These work fine 99% of the time. Choose the right drill size, keep tapping as you spin, works just fine.
@da86172 жыл бұрын
Thats crazy , im actually about to graduate college in December for Aerospace Engineering and dont know where to start , any advice/tips ??
@andoniades2 жыл бұрын
True, a lot of people tend to hurry and overtorque, thus breaking the easy-out. It's a simple system.
@HotshowDreamer2 жыл бұрын
What is name of this wrench
@JDuBz8152 жыл бұрын
I usually end up snapping the extractor in the bolt I've drilled out. But that's on M6 and smaller bolts usually with the smallest 2 extractors. Major pain
@DigitalArtisan772 жыл бұрын
Buy snap-on or quality extractors. Impact hardened with impact driver even better, grind tip off extractor if too long and weak.
@JDuBz8152 жыл бұрын
@@DigitalArtisan77 Lol I have both snap on and mac. Nice try tho
@JDuBz8152 жыл бұрын
@@DigitalArtisan77 I will say the stubby MAC easy outs are some of the best I've used. They just don't go small enough for the bolts I tend to work with most of the time.
@davidorozco1888 Жыл бұрын
@@JDuBz815 any tips for a deep broken m6 in an aluminum motor casing? My 30 minutes job has just turned into a nightmare
@JDuBz815 Жыл бұрын
@@davidorozco1888 what have you tried? Blind hole?
@tomwilson15842 жыл бұрын
Always use a tap wrench, with an easy out.
@RobertoMartinez-hj4xj2 жыл бұрын
no se porque para todo usan la cresent
@antoniorenteria28962 жыл бұрын
They need to start making round Allen keys for when this happens
@sleepysloth78852 жыл бұрын
Big brain
@gameyord71822 жыл бұрын
@@sleepysloth7885 small really because it will slip
@joceliofidelis16762 жыл бұрын
Tô
@joceliofidelis16762 жыл бұрын
Gente
@davidcouch65142 жыл бұрын
How does one think of such lol
@andrewerickson66902 жыл бұрын
It would be amazing to get a bolt out that easy
@stompy6762 жыл бұрын
Step 1 drill a hole. Step 2 use crescent wrench backwards. Step 3 remove bolt.
@duncemonkey142 жыл бұрын
Not to mention pounding on the easy out...eek
@cbrunnem61022 жыл бұрын
More often then you'd think, just using a left handed drill bit will work.
@samhillyersh2 жыл бұрын
Theyre just so much easier to use than right handed ones
@cbrunnem61022 жыл бұрын
@@samhillyersh you are making a joke but I'm not. Normal drill bits are right handed and when used youbrotate the clockwise. That would tighten a bolt. A left hand drill needs to be spun the opposite direction and could loosen a bolt.
@machineman8388 Жыл бұрын
@@cbrunnem6102 does it actually though? Because in a hole thats not a blind hole, (accessible from both sides) I've yet to see a RH drill bit push the screw through the hole, so why would. LH bit pull it out?
@cbrunnem6102 Жыл бұрын
@@machineman8388 a LH drill bit can end up grabbing it and rotating it out. especially if the head is left. it just works. don't it dozens of times.
@user-bz1ol5cr4j2 жыл бұрын
Такую тайну показали что просто слов нет😁😂
@TheMarylandRoadKing2 жыл бұрын
Genius! Tap it out. Never would have thought of that!!
@coltshooter56032 жыл бұрын
Awesome....do this with about 2" radius clearance deep inside an engine bay😂
@borego042 жыл бұрын
Exact pal its clear everything easy
@StoneInMySandal2 жыл бұрын
Use a tap wrench to turn the extractor. The leading cause of broken extractors and fasteners with even more damage is uneven loading of the extractor.
@michaelstippich34642 жыл бұрын
Good job, but it usually doesn't work that easy 🤨
@trivo78742 жыл бұрын
@@michaelstippich3464 day
@emmanuelbueno37252 жыл бұрын
By
@kuubleekahn68932 жыл бұрын
My favorite part is when you snap the easy out off in there as well.....nothing better than that feeling
@ferrumignis2 жыл бұрын
Really makes your day
@kuubleekahn68932 жыл бұрын
@@ferrumignis snapping an easy out off in a bolt 🤤🤤🤤 ughhh gets me so moist 😍 😂😂😂😂
@centermass49622 жыл бұрын
Wow is that how u do it? Iv been using the extractor upside down this whole time.
@edwardvankirk35152 жыл бұрын
There's a Tap "T" handle that goes on the square at the top so you don't strip or crack the Tap
@Noname-dc9mm2 жыл бұрын
Where’s the tap ?
@edwardvankirk35152 жыл бұрын
These are the same thing as a Tap & Dye set with a "T" handle to turn them the "T" handle fits these extractor sets also if you need it put more plainly they even have ratchet "T" handles for the tap and die that fit the extractor taps
@Noname-dc9mm2 жыл бұрын
@@edwardvankirk3515 thanks for that but unfortunately when you put it plainly for me it confused me more. I just can’t seem to visualise a ratchet T handle on a die stock.
@edwardvankirk35152 жыл бұрын
Not worth the time to explain
@edwardvankirk35152 жыл бұрын
Push your Google button search it and educate yourself
@MrHidibo2 жыл бұрын
These removal tools are ok but they expand the bolt sometimes making even more stuck
@madbug19652 жыл бұрын
I agree. They don't always work.
@grincadorna47532 жыл бұрын
Nahhhh your negative
@MrHidibo2 жыл бұрын
@@grincadorna4753 no mate I have over 25 years experience and use these tools on a daily basis
@mike69322 жыл бұрын
That's why they invented helicoil 😆
@MrHidibo2 жыл бұрын
@@mike6932 amen to that, the best most effective way for me that is, mig a washer to the broken bolt then mig a nut to that the heat from the weld goes into the bolt too then it should Possably maybe come straight out no problem lol
@leehunter12462 жыл бұрын
They've been called easy outs for years
@NickoOutBush2 жыл бұрын
use them all the time successfully... in australia we call these tools “easy outs”
@hallwest96502 жыл бұрын
Here in Merica we call them that also
@antonioabrego43212 жыл бұрын
I knew that 30 years ago. Thanks for reminding me.
@plotcky2 жыл бұрын
On internet every basic task can be interpreted as a professional lesson.
@jajael78532 жыл бұрын
2 in 5 chance the EZ out snaps.
@TheBear3282 жыл бұрын
Yep. Only a moron would leave the head on while using the eazi-out.
@larrystuder85432 жыл бұрын
Been there, done that. Sometimes with a 1 inch Allen bolt, at the bottom of a 6 I ch deep hole. Sucks, big time...
@jajael78532 жыл бұрын
@@larrystuder8543 everyone watching this was waiting for the *snap".
@mdfield12 жыл бұрын
I’ve got the same set of easy- outs. However, he used the crescent wrench BACKWARDS! It can sometimes work that way but it works much better when used properly.I was a mechanic for large manufacturing companies so I know of what I speak.
@joseangelfloresgonzalez56822 жыл бұрын
Torpe para comer unas llaves y k bueno cuando le interesa
@TheAbidimtiaz2 жыл бұрын
Please tel me the name of this tool.
@teodorcioaia65952 жыл бұрын
@@joseangelfloresgonzalez5682 .
@drtydude22662 жыл бұрын
I’ve tried that kit so many times and never got a screw that was seized out. It might work if screw is slightly tight that’s about it.
@benjaminflack92642 жыл бұрын
Agreed. Getting any rusty stripped bolt out is like winning the lottery
@_1ben2 жыл бұрын
I have had some success, little, but on this I would try heat?
@JDuBz8152 жыл бұрын
Heat helps quite a bit. Using the biggest extractor possible helps. But I've snapped more extractors than I have successfully gotten the bolts out lol
@Nobody-Nowhere-USA2 жыл бұрын
As a machinist I would like to say, Easy Outs work! Haphazard at best but they do work! Sort of! Lmao 😂
@gillesgoulet25452 жыл бұрын
I use a torx bit and hammer it in and remove with a ratchet. works great
@friend60972 жыл бұрын
Там болт в масле , и так бы открутился . Вот с блока цилиндров закисшую шпильку бы он так выкрутил ,это другое дело
@txgunguy27662 жыл бұрын
Or just use a Dremel to cut a slot into it and then unscrew it with a flathead screwdriver.
@derrickgentry86952 жыл бұрын
Tru dat
@simonsaade38972 жыл бұрын
Yea that's the thing you do before piercing it
@futureonjk2 жыл бұрын
Um, left hand drill bits works great too. Since the threads go to right. Unless its left hand threads. You use regular drill bit (AKA right hand).
@tagapiouplayz37372 жыл бұрын
Links to the tools would be great
@CheddarBayBaby2 жыл бұрын
Try doing that under the hood of a 95 Ford probe. 🤣😭
@Cg.mtb072 жыл бұрын
If you didn't round out the bolt then you wouldn't have to do this
Used to have a set like that, don't remember where's now. 😁
@lineyka67962 жыл бұрын
Гайку сверху приварил на 2-3 прихватки и выкрутил... не усложняй сущности, без надобности...
@chevybigblock33112 жыл бұрын
Judging by the all /16 he used on the extractor he’s probably the one that tried to pull a 6mm alan head bolt with a 5.5mm key 🤣
@madhusudanbhoi31272 жыл бұрын
Ychttb ha mmmmvxxxxx
@jonathantoohey20372 жыл бұрын
The bolt holding the brakes to the fro t fork of my bike is like this, I'm glad I found this video
@superviking24682 жыл бұрын
Best feeling ever when that bolt turns .... omg
@superviking24682 жыл бұрын
Right ?!?! Cmon !!
@repobud12 жыл бұрын
Allen keys are meant to work perpendicular to the fastener going at it at a 45 degree angle doesn't work
@kokobrais2 жыл бұрын
Судя по остальным засверленным шляпа полная , это была самая удачная попытка.
@dimasamsonau36462 жыл бұрын
говорят, что конкретно эти экстракторы полная хуйня
@dimasamsonau36462 жыл бұрын
другой формы и другого вида экстракторы в виде пики крестообразной еще может быть... но не это фуфлостракторы
@AntonioPerez-gd6dy2 жыл бұрын
@@dimasamsonau3646 Catastro Get la
@AntonioPerez-gd6dy2 жыл бұрын
Y Venta
@mada90x2 жыл бұрын
This saved my life so many times
@alicesrustychains67672 жыл бұрын
Better off welding it up then twisting it off before snapping the easy outs lol especially on anything aluminum the welding trick is amazing
@user-wb8rp3mp1m2 жыл бұрын
Уоаопвра☺😀😆😆😉😆
@user-fe8yg2lt5d2 жыл бұрын
Если бы он был нормально закрученный, шляпку болта обрезала бы и прошлось бы высверливать болт и нарезать резьбу.
@vaporhtrail43502 жыл бұрын
Take some copper wire, bend it into a U shape and put it into the stripped opening. Then add your bit/tool. Works 60% of the time.
@Anonymous83172 жыл бұрын
60% of the time….works every time - Ron Burgundy, master carpenter
@johanneshofstetter39492 жыл бұрын
I must try this
@user-zs4ow7fd3y2 жыл бұрын
@@johanneshofstetter3949 հ
@thaythuocvietnam30992 жыл бұрын
00 UB
@jameseastwood49842 жыл бұрын
I've broken a couple of these and never got them to work. Rose-weld a nut on top is better, as the heat also works in your favour.
@andoniades2 жыл бұрын
You used with a tap wrench with even pressure / force towards the threads? Sometimes while lightly tapping? It should work 90% of the time.
@robertgutheridge96722 жыл бұрын
The problem is easy outs don't work 2/3 of the time they break off inside and then you have hardened steel to deal with as well I found that before I start twisting on the EZ out if I take a torch and heat up the area around the bolt that I'm trying to remove helps immensely the heat from the torch makes the metal around the bolt expand a couple thousands of an inch or so but it helped break the rust loose
@michelecalais17852 жыл бұрын
Je nadmet pas la langue anglaise
@user-qv6uj1ow1o2 жыл бұрын
я слыхал что есть способ, розсверлить убитый болт, и нарезать в нём левую резьбу, и вкрутить туда собственно болт с левой резьбой, до упора, и оно выкрутиться
@nurgender46872 жыл бұрын
Не у всех есть болты и метчики с левой резьбой одинакового шага - они не маст хэв
@zov40282 жыл бұрын
Авсверлить проще
@user-eg4ih3rm2h2 жыл бұрын
Доктор Дью уже выехал за ними))
@dfgadasgag43962 жыл бұрын
Так как он крутит, ему для каждого болта эта елда понадобится)
@antonh4062 жыл бұрын
А еще можно просто приварить другой болт, главная проблема это доступность
@user-ch5xj6lj9k2 жыл бұрын
Экстрактор помогает разве что 2 раза из 10 случаев.
@penguinkowalski36602 жыл бұрын
А точнее в тех где болт насмерть не прикипел. Иначе есть шанс обломить экстрактор.
@Luminous_trident2 жыл бұрын
@@penguinkowalski3660 ну дык сначала вдшка, потом экстрактор
@ivanzolotnikov2742 жыл бұрын
Болт был откручен зарание-видно!
@TraumaER Жыл бұрын
Exactly what I need!
@philipchavez97212 жыл бұрын
Craftsmen tools are not the highest quality, but they make a way better extractor kit. The bits have a 13mm head, use a socket and ratchet or a 13mm wrench in a tight spot. They also make an external extractor set for bolts with stripped heads.
@user-wn5op6cy5c2 жыл бұрын
Для тех кто не умеет пользоваться ключами.
@user-pf6xu7vl3g2 жыл бұрын
Ходит легенда, что экстракторы именно так и работают 🤣
@user-bm5xl3db1w2 жыл бұрын
Ты хоть что-нибудь в жизни открутил экстрактором? У меня не хрена не получилось🤣🤣🤣🤣
@user-pf6xu7vl3g2 жыл бұрын
@@user-bm5xl3db1w так в том то и суть что нет)))
@user-bm5xl3db1w2 жыл бұрын
@@user-pf6xu7vl3g нас жестоко на&Бали🤣🤣🤣🤣🤣
@Sk4M_.RangeroftheNorth2 жыл бұрын
Spot on!! Good lad.👍🏽
@drewgalante4722 жыл бұрын
drill the head out first, if the bolt hasn’t bottomed out it should only be tight on the shoulder then you can use an easy out or left hand drill bit. doesn’t always work but it’s a good starting point if welding a washer and nut doesn’t work
@blkrobnpk2 жыл бұрын
Yeah until the tap breaks inside the hole you got to drill out the tap.
@kennethparker21682 жыл бұрын
Been there done that more times than I can remember A broken easy out is no fun
@jaybee72912 жыл бұрын
A tap is for threading....... he is using a stud remover, two completely different tools my friend
@blkrobnpk2 жыл бұрын
@@jaybee7291 yes I understand that, I guess you never had an extractor break.
@basketofdeplorables42532 жыл бұрын
@@jaybee7291 not a stud remover either, it’s called an easy out or broken bolt extractor. Definitely not a stud remover.
@sergeiangolenko79362 жыл бұрын
Ну вот кто станет этим заниматься? Да ещё и деньги тратить на приблуды, сварка же есть у каждого
@user-cz4ir1xq1s2 жыл бұрын
Сварка бесплатная?))
@sergeiangolenko79362 жыл бұрын
@@user-cz4ir1xq1s дешевле выйдет чем куча этих экстрактором и дрель покупать
@sergeiangolenko79362 жыл бұрын
@@user-cz4ir1xq1s ну это комент к видео, на сам деле молотка достаточно
@user-cz4ir1xq1s2 жыл бұрын
@@sergeiangolenko7936 моя свареа например стоит сотку, экстрактор и дрель 5))
@sergeiangolenko79362 жыл бұрын
@@user-cz4ir1xq1s так она(сварка) у тебя уже есть, а то ещё в магаз сбегать прикупить надо
@jagoxtv30072 жыл бұрын
Dari Awal sampai Akhir Video nya sangat Menarik.. Di tggu Video Lainnya..
@nowellveracruz87202 жыл бұрын
Thank You Bro . You give me Idea 😄
@vuruaa2 жыл бұрын
溶接が最強って、答え出たよな
@fedorbelkin85142 жыл бұрын
Явно руки не оттуда, о как он шестигранник вставляет
@iiiiiiiiiiiiiiiiiiiiiiiiiii9202 жыл бұрын
Доктора, позовите Доктора!!!
@BradVitOfficial2 жыл бұрын
@@iiiiiiiiiiiiiiiiiiiiiiiiiii920 здраааааасть
@jamalwilliams17922 жыл бұрын
This is creative and satisfying to watch
@renostubbs85042 жыл бұрын
This is definitely a keeper
@hondaturbo6662 жыл бұрын
You're even using the wrench the wrong way
@jangsupark12 жыл бұрын
아주 유용한영상 굿
@kyletrump80252 жыл бұрын
I don't think I have ever seen an extractor work in real life
@ilp4162 жыл бұрын
Ни разу у меня такой экстрактор не сработал, чаще всего они обламываются.
@user-pi6hn3oc8k2 жыл бұрын
У меня тоже обломались, а обломок ни высверлить ни выбить, была жопа до екстрактора, после него стала полная жопа!)
@kevinburns57622 жыл бұрын
Wow. Could've saved yourself a shit load of hassle by just inserting the allen key properly in the first place 🤷♂️
@shenannoel34992 жыл бұрын
someone teach him how to use the basic tools first 😂😂😂😂
@user-bz4oq5du5n2 жыл бұрын
おーお見事!まさかドリルの大きさで六角のネジ山潰れたの取るとは。日本とちがうけど参考になった!
@user-ee7xj4jj2b2 жыл бұрын
ドリル?逆タップではないでしょうか?
@RogelBoyKabatmanVlogs2 жыл бұрын
That’s good ideas for me thanks for sharing
@mikeznel60482 жыл бұрын
Where is the removing of a broken bolt?
@yanglaybson73312 жыл бұрын
Colocando a ferramenta torta daquele jeito não tira nenhum parafuso mesmo 🤣😉
@battlechurchapostolicminis2002 жыл бұрын
I always saved my ex boss money by keeping a set of quality back out tools w me, the cheap ones break too easy
@andrewkaraiskou47902 жыл бұрын
This is nothing new I was using this method 30yrs ago
@battlechurchapostolicminis2002 жыл бұрын
@@andrewkaraiskou4790 you are old lol I’m not that old
@Eurogigolo2 жыл бұрын
Or weld a wrench onto the bold and you can then easily unscrew it
@jankriz46112 жыл бұрын
Finally something new in the world!
@scottyo642 жыл бұрын
I have never had any luck with that type of extractor.
@iatea_Cow2 жыл бұрын
I like how the title says “2021”, like this wouldn’t work in any other year.
@MD-NWWI2 жыл бұрын
You use an adjustable wrench backwards. It should go the other way
@INDIAN-gz7xg2 жыл бұрын
HOW TO TAKE BROKEN DRILL BIT 1.5mm DIA FROM AN ALUMINIUM CASTING?
@jdkrxw2 жыл бұрын
Just go a little deeper with the drill, until the hex head comes off. The exposed bolt shank isn't hard to get out after the gearbox flange is removed. A broken ezzee out is a huge pain.
@bryanbaldwin73702 жыл бұрын
Left handed drill bit in a drill press slow speed with a little PB blaster on it and back it right out .
@andyr53892 жыл бұрын
Take a socket torx bit and hammer it in the rounded hole. Then use a ratchet to remove. Doesn't always work but way quicker and easier than this for a first step
@user-cl4xd4fv8s2 жыл бұрын
Boss: you are fired
@csurams842 жыл бұрын
Works good on KZbin video. As soon as you try it at home, please believe it'll snap on you. Lmao
@Nogapniba2 жыл бұрын
I get those goodbumps every time yeah
@nathanrobinson295610 ай бұрын
Tried this trick several times to absolutely zero success. That bolt face was rusty, but had definitely been removed before trying to use the Left handed drills etc as there was zero rust around the bolt.
@hiroshiyt_ Жыл бұрын
Bro, turboflex gon' sue you
@pacsvlog3252 жыл бұрын
Very nice moves Shout out lodi
@deenojarmbo29222 жыл бұрын
easy out and a little WD wouldn't hurt.
@nickscarboni70082 жыл бұрын
Don’t turn the wrench backward !
@poymenov2 жыл бұрын
Wow u must be colbus related. You have rediscovered americaca
@livefree10302 жыл бұрын
Wow, using an extractor kit. Amazing.
@musicased9591 Жыл бұрын
Must be real nice having the clearance to do that. Now try it with the parts actually on the car
@joeparker2822 жыл бұрын
Usually stripped out,heat beat
@dilemma_yt2 ай бұрын
How did you strip the bolt if it was that easy to twist off in the first place. I want to know how to remove a stripped bolt that even with a 2 foot long leverage, that bolt aint moving.
@joseph-kp8upАй бұрын
I've broke every extractor I've ever used. 😂😂
@douglashernandez25202 жыл бұрын
Wow! That's amazing! Now Ik what there for!🙏😂 thank you ,so much ,goodnite'🙋♂️