How to remove SMD components without hot air gun

[@buddhistsympathizer1136]

This is a great idea, but it would have been better if the repairer had applied low-melt solder to the pins carefully using a standard iron BEFORE using the copper wire tool. It would have been much faster to remove the IC.

[@klazzera]

5:40 - how to fry IC's by applying medium temp soldering iron for a solid 100 seconds

[@MrRobuz]

I agree was putting a lot of heat on the circuit board. Once you can move the chip around remove it.

[@coloradowilderness3139]

Actually Tin soldering.

[@tomych20]

Good idea, but in my opinion this copper wire should be tinned with solder and then the result will be even better.

[@rrafal]

Also sand the copper wire to remove the layer of varnish

[@RahulVerma-xe1cs]

बहुत ही अच्छी वीडियो आप को दिल से शुक्रिया मेरे भाई

[@stargazer_100]

The application could be improved significantly, but the idea is sound. Thanks. I wouldn't start practicing on big chips in tight spaces where you would possibly be reusing those ICs. And yeah, I think the wire should have been pretinned. It's going to get tinned one way or another and the time to tin the wire is not while you're trying to desolder 100 pins in a tight space. Heat transfer is way better with tinned and fluxed wire. A hot air gun is no guarantee that you're not going to "cook" a chip, and it is no guarantee that you're not going to move close components. Technique with the right temperature can beat any tool.

[@gwangju1]

Be careful with silicone thermal grease, if it gets on the connections forget about ever getting a good solder joint.

[@ytrew9717]

if it happens, is there a way to solve this problem?

[@UltraNyan]

How to cook ICs without hot air gun.

[@sfp4197]

European people get out smd's without a hot air gun with a car ligth bulb

[@UltraNyan]

@@sfp4197 ... and Australians just let the PCB cook in the sun.

[@Patrik2166]

Fry it in an oven then slap those bitches down the PCB 😤👌

[@khanv1ct244]

They’re a lot more heat resistant than you think.

[@Firebird31001]

@@UltraNyan And Russians just use a freakin soldering iron

[@carserviceportugal]

I was looking for a technic to dessolder very small components from old donner boards, that have leaded solder...hot gun is useless!! This is the best trick if you do not have hot twizzers! Thank you.

[@nonamex3052]

The excessive heat will mostly damage the components....that's why they use hot air gun because such small components can be easily damaged by direct heat

[@abdulwaaseihsultan7733]

What an artist you are! Simply brilliant ❤️❤️❤️❤️❤️❤️

[@nimalperera5454]

What is the size of the wire you used, what is the type of flux you used and what is the paste you applied around the tip of the soldering iron to fix the wire you made? Very interesting video.

[@Jessterrr]

Brilliant hack! I'll probably use that at some point - especially with chips. I'd be concerned about stressing a component near a chip like a cap or a zener diode.

[@nimaichandsamanta5608]

Nice video, please check the datasheet of the components you are soldering or desoldering.Otherwise the components may get damaged due to extensive period of heat.

[@NoMoreBsPlease]

Doesn't matter if it's already damaged.

[@saddle1940]

We lost some pads 4:13?

[@nocturnal0072]

@Li Feng use a normal soldering iron, go from side to side.

[@nocturnal0072]

@@saddle1940 the pad was a blank if you go back a bit.

[@nocturnal0072]

Best way I found to salvage parts is to use a lighter or straight up hair dryer on the back of the board. However this destroys the board but saves larger components. Small caps, resistor, ferrite cores usually don't need more than a good iron and some solder.

[@homemadeprojectofalltypes6530]

Aapka bahut bahut Dil se dhanyavad sir🙏🙏🙏🙏🙏

[@JKnight89]

The only issue with this is the amount of time the iron sits on the component. If replacing bad component, this might damage the circuit boards copper traces, if salvaging the parts, might overheat n damage/distroy them..

[@getz]

Like at 4:14, you can see the pad missing

[@shahsuleman7552]

@@getz the pad is factory missing.

[@biketayo7055]

what is the title of song

[@max_rockatansky_2001]

anthony ocaoi The song is called “Annoying”

[@provideo2894]

yes this man distroyed other parts too.

Emeğine sağlık ustam tebrik ederim 👑🤝👍

[@kapilsds7]

in my school days, i haven't money for smd station. i always doing it your way.

[@gkhatiwada5939]

Tecnic is beautiful well done... 👍👍👍

[@edwardocamarinha5438]

exellent cheap idea, congratulations

[@ATdiy]

Thank you

[@KTHKUHNKK]

@@ATdiy I just subscribed can I pay you to do a small job for me ?

[@KTHKUHNKK]

@@ATdiy Absolutely superb the way you did that. Keith

[@SamLoinch]

不错的项目，继续努力

[@DanHomeAtLast]

Pretty good idea. Can you tell us the gauge of copper and hear range you've used here?

[@МитяОпонасенко]

Хорошая, проверенная временем, технология из двадцатого века, спасибо за видео.

[@maxjlg2319]

Fantástico e muito funcional 🇧🇷🇧🇷

[@victorgonzalezrodriguez488]

felicidades por tu ingenioso truco, nunca me hubiera imginado que su puedira quitar un ci, tan facil, aun con mis 25 años como radiotecnico, no cabe duda que siempre se aprende. gracias.

[@satishm4635]

09:00 I liked the most. Thank you!!

[@borjoobhumij1836]

IT IS VERY HELPFUL FOR ME❤🙏🙏🙏

[@kapioskapiopoylos7338]

aka how to destroy every single pcb trace to save 50$ on a cheapo heat gun 7:18 RIP NEC IC you will be missed O7 along with destroying ICs etc wasting wire as every package needs different paterns or whatever you call that

[@josepeixoto3715]

wasting wire......lol

[@zahiddawood4294]

Wow good idea i like it. [PAKISTAN]

[@ritaeremina1786]

пока ковырял и плавил припой - половину элементов снес )))

[@КремнийнаСапфире]

Идея интересная, но не везде применима. Если перед этим применить Розе думаю соседние элементы не пострадают.

[@МОТОБРАТСТВОДмитрийЧеремис]

Перегрев деталей и микрух!!! Сомневаюсь что они выжили после такого

[@1966pda]

МОТО БРАТСТВО Дмитрий Черемис Вопрос: зачем их отпаивать , если иправны? По нормальному- полупроводники два раза паять можно, один раз впаивать в плату, второй раз снимать нерабочую с платы!

[@СергейТ-ф8щ]

@@1966pda если ты так рассуждаешь, то ты имеешь отношение к ремонту электроники так же, как я к астрономии, то есть любуюсь ночью звёздами на чистом небе.

[@KosikX]

Автору было не удобно на камеру выпаивать, в реале там быстро всё, и сплав розе моментом растекается.

[@agunglaksono1159]

This is very creative, it is very useful for me who likes to take apart electronic devices 👍👍😁

[@rishabhsharma6084]

this process is to remove dead ICs. otherwise working IC will be dead bcos of excessive heat.

[@nimalsandunsiri4024]

You are a real genius.👍🇱🇰

[@oscarlores8010]

Like. Pero es mejor para mi no se para ustedes con un alambre de acero por debajo de las terminales y alar calentando.

[@ATdiy]

Thank you so much

[@biketayo7055]

what is the title of song

[@heiferTV]

Exception By Jincheng Zhang

[@oscarlores8010]

Un calentador de motor de gasoil o petróleo

[@alescitocp3802]

@Kevin Zambrano es una bujìa de precalentamiento de motor diesel ;)

[@DjRicolaz0328]

.. this idea very helpful without Air gun😇🤗

[@maui-maui4011]

7:10 Over 1:30 minutes to remove that chip I didn't catch why don't blow up all circuits although some other smd components have been moved

[@tallxcrunner]

One word... Chipquik. I use it every day. It is a special solder that stays melted longer and you can remove any chip much faster and easier than this method. You apply flux, melt some chipquik around all of the leads, and just move the iron around the chip until it breaks free. Whenever I show people how easy it is, they are dumbfounded. If you need resolder the chip, apply flux and clean it with some wick.

[@miguelricardo4845]

Really BAD procedure to remove SMD Ic's, not recommended. You can do that much faster and safer using ChipQuik SMD1without boiling print and nearby components. At minute 7:17 watch the adjacent two smd capacitors being moved out of the print due to the extreme heat.

[@FrankBatistaElJibaro]

He did a likewise horrific job at 4:15. It's amazing idiots are upvoting this guy and his art for destroying ics and pcbs.

[@Periferieradanka]

What's even worse than the two capacitors is how he pushes a resistor on the bottom left side of the IC so that it connects to another capacitor rather than it's intended position... This is a horrible technique.

[@miguelricardo4845]

​@@Periferieradanka I missed that, is even worse. :) Good way to create 10 faults trying to fix one.

[@fabionicolaudelima4185]

@@Periferieradanka LOL! I missed that!

[@Hammerjockeyrepair]

you watched that far in?! lmfao

[@sameernjm7879]

سلمت يداك طريقةحقامبتكرة الله يزيدك ويزيدنامن علمه

[@a51mj12]

Right, and the video skips right before the component is "unsoldered"

[@silencethequiet]

Moon landing faked confirmed

[@alfredoportillo9]

Que bien felicitaciones por enseñar cosa novedosas🤝🤝👌👌👍👍

[@mariosergiogroetares9343]

Valeu! Muito bom! Método caseiro e eficiente! Grato! Boa tarde!

[@AteuCu]

Boa-tarde *

[@Yezhik_v_Tumane]

thank you very much for the idea, Hello from Russia

[@AP-hx2jw]

А реболинг на утюге с горящими углями? Like

[@СергейСкрипников-ы8э]

@@zolotye-ruki нет, но почему-то все в России так его и называют

[@zolotye-ruki]

@@СергейСкрипников-ы8э НИКТО в России так это Не называет!! В России это называются у ВСЕХ - накатка шаров!!

[@СергейСкрипников-ы8э]

@@zolotye-ruki Если вы называете ЭТО так, то это совершенно не значит, что все называют или должны называть ЭТО так! Пусть как хотят, так и называют, вы же поняли о чем речь.

[@zolotye-ruki]

@@СергейСкрипников-ы8э вот именно, что если ВЫ так это называете, это НЕ значит что ВСЕ так называют!! Ты в России живешь сука а не в АМЕРИКЕ своей ебаной, что б тут выражаться всякими вражескими терминами!! ВСЕ электронщики, с которыми я общался, называют это НАКАТКОЙ шаров!!

[@СергейСкрипников-ы8э]

@@zolotye-ruki ты часом не из этих самых - скинхедов?

[@GeorgeGeorge-xj2bc]

Nice idea that you can use in a case of emergency or outdoors since the electronic repairsman has trained to be ready for desoldering of any package components even in the hardest enviroments on the planet making himself all the neccessary tools from any available source.

[@walkerhawes2200]

What is the clear substance that you put on the components right before you put the heat to them?

[@mrkitty777]

Flux, but I don't know its compounds.

[@edsonpaschoal5744]

Prático tem q ver se o calor não vai danificar o componente. Graxa térmica???. Onde encontrar

[@arielitogato]

@@edsonpaschoal5744 La encuentras en tiendas de electrónica o de computación (suele costar más ahí), se usa para instalar disipadores (heatsinks)

[@Milkex]

@bLx It is not anything like an "oil" it is an acid suspended in a denatured alcohol

[@marciorodrigues4421]

@@edsonpaschoal5744 fluxo de solda para estanho compra em loja de Refrigeraçao

[@Prash1c]

Fantastic idea!!! :D Summary: 1. Apply thermal paste to conductive surface 2. shape copper wire and fix to conductive surface of soldering iron. I would mod step#2 and use nichrome wire maybe?

[@ivonedialkov3628]

А

[@rogeronslow1498]

The music is sooo unique!

[@radem.5571]

Guys everyone who knows something about soldering won't do this ! This may damage your board. If you do not have hot air gun use common soldering iron and desoldering wire or solder wick. They are the same thing but 2 different names!

[@FLomasterZ]

Boards made in USA will be good if you solder like this 100 times and more. I think you need to set right temperature when you are soldering. ;)

[@ipasuhd]

now try to solder it back, with the same tools!!!

[@yagyaveersingh3993]

Maza aa gaya gajab ki trick so thanks

[@valfridotrelha6218]

Parabéns amigo, nota 10 !!

[@khalildaoudi5895]

شكرا للمعلومات ، ساعدتني كثيرا.

[@uchodzcazarobkowy850]

What is the gel you're applying before de-soldering componentss?

[@applepurple2083]

Flux gel

[@slackdm]

@@applepurple2083 Thanks

[@djones98501]

Very cool, also consider pre heating one side and switching direction of the element to finish heating

[@danja7254]

сколько можно одной музыки пожалуйста поставите другую музыку!!!!!!!!!!!!!!!!!!!!!!!!!!!

[@АндрейШмаков-й2г]

А выключить звук ума не хватило?

[@ashoksher8150]

Bahut bahut Shandar sir g

[@GezielLimapqp]

Cararca, essa cara e um genio! como não pensei nisso antes!

[@tiamat6734]

mano,que produto cinza é aquele que ele usa no ferro de solda?

[@shinningraj]

these techniques are good for newbie(s) not for professional(s)

[@BobcatYkt]

Судя по изощренности устройства это эмигрант из стран СНГ

[@СашаНикин-ш9ю]

По ходу да ,нам в технарей на монтажной практике показывали эти "чудеса" только паяльник 40 ват и провод моножила 2.5 квадрата сечение. Сейчас смотрят как упрвляюсь говорят "ГУРУ", Как можно без фена и термопицета и инфракрасных приблуд.

[@petrlicht]

Great...thanks for helping. Good idea without air heatgun

[@fddizon1]

what kind of flux did you use?

[@M4CHINE69]

Lemon juice

[@valerya4532]

Классная идея, сам думал в этом направлении, excellent

[@benceszabo5515]

I love how he copy pastes "Thank you so much" to every positive comment

[@GoatZilla]

Thank you so much

[@doctorcircuit5338]

Chip quick works great and at low temperature try it for best results

[@roberto7285]

Os fabricantes de estação de ar quente, devem está no google maps procurando voce! kkkkkkkkkkkkk

[@jantechtube.1458]

Good for dead smd components. Good job

[@vnukchaknorrisa5964]

С таким макаром нужно олова не мерено запастись.

[@ОлегВиноградов-ю6к]

Припой - расходный материал. К тому же никто не запрещает использовать его повторно.

[@Богдан-ч5ы1г]

И термопастой.

[@recuperacaorecuperacao7329]

Fala em português, man!! Assim fica difícil! Parece que ta falando russo! 😅😂

[@cygnus58]

Carefully dremel off the legs. Solder wick remnants. Tin pads. Place new chip, heat several leads at a time thru wick. Leaves just enough under pads to make contact well.

[@shaneintegra]

He was boiling the shit out of those lol

[@yopapi6624]

0m3n if the components malfunction it doesn't matter, and he did remove them fast though.

[@shaneintegra]

@@yopapi6624 The video was sped up so it wasn't that fast lol

[@waynet8953]

The liquid actually keeps the temperate from rising much beyond the boiling point (of the liquid).

[@mahatana_r]

I knew reading the comments would be more interesting. lol

[@juansolo1617]

Notice how the boiling point of the flux is well below the melting point of the solder.

[@abdsakowa]

I will give it a try one.looks very interesting and clean

[@duclinh84bk]

It takes to long when remove the DIP IC, this might cause the damage on IC!

[@gtrman9706]

Too long. 😂 😂 😂

[@dynamicdeals1]

*Bro your skills are great this should he seen by every electrician*👍🏼

[@erdemkaya6291]

RIP smd.

[@travisfrost6508]

Creative idea👍 Thanks! I’m going to try it right now!!

[@haitham.sultaneh]

Very very fantastic

[@ATdiy]

Thank you so much

[@abbeyzondo]

Wow great idea. Thanks. Is that thermal paste on tip of soldering iron?

[@GroundControl204]

too much risk burning up the IC chip and even burning out traces on the PC board that surrounded the chip. not a good idea at all.

[@abdulbilakhiya6026]

Appreciate idea congratulations sir very nice

[@zhivkomarinov5449]

That is not professional job. This is extremely stupid. If you are an electronics technician, you should know that for the electronics elements it is used rework solder station.

[@ВалерийВалерджан]

Задумка не плохая, только перед тем как выпаивать детали вам надо залудить ваш сделанный паяльник, будет быстрее

[@qorxmazveyselov5163]

А что за паста ?

[@rickywong6946]

4:17 failed?

[@Jp-bk3yw]

yeah.

[@lenierdelacruz3588]

Me parece fenomenal la metodología de extracción de los componentes SMD puesto en este video

[@reaktor_477]

Фен вам в помощь

[@DmitroMos]

Фен для слабаков!

[@reaktor_477]

@@DmitroMos ну точно не для бичей )

[@КремнийнаСапфире]

@@reaktor_477 Фен для бичей BGA станция для тру ремонтеров.

[@reaktor_477]

@@КремнийнаСапфире Если я не паяю целыми днями то и станция мне нах*й ненужна

[@КремнийнаСапфире]

@@reaktor_477 На ней и мясо можно пожарить Medium Well.

[@domenicodimatola7102]

Salve Che materiale e quello messo sulla punta del saldatore prima di avvolgere il filo. Grazie

[@HoangNguyen-sb7kw]

8:48 You are going to burn him..... :3

[@bennymannaparambil5752]

good work... but I think , you apply soldering lead to all the legs of smd before apply soldering iron

[@valdemardemello4192]

Lo malo es que tenes que usar mucho estaño

[@biketayo7055]

what is the title of song

[@nyamjargalsaihan4640]

It is great. I have one question. What is the name grey thing?

[@nyamjargalsaihan4640]

Oh ok. thank you...

[@filipiandradecastro5605]

Pouco eficiênte

[@alfredoqueiroz3536]

Tbm achei retira muitos componentes em torno do setor a ser realmente removido

[@miguelricardo4845]

Do PIOR que já vi. Poderia ter utilizado o ChipQuik SMD1 que seria muito rápido e eficaz. No minuto 7:17 até está a levantar dois condensadores SMD da pista ao lado. Amador!

[@fkjos7682]

This is excellent. Thanks for the idea !

[@amarshrestha3870]

Title should be, "How to roast SMD components without hot air gun" You will damage every single component and adjoining components.

[@tosintoel6268]

mantap boss ku solder nya unic....harus panas....

[@mrdearregards1342]

Не удобная хрень. Задумка хорошая из свечи паяльник но насадки говно!!!

[@erlanggahaadys3280]

Dimas Ryadinskiy h

[@arnoldusvirgobanne2497]

Thanks So much for video. God blessing.

[@killabee623]

Hey ! you lost a pad. Invest in a hot air station, they are cheap.

[@IIGrayfoxII]

Where? On that DIP16? There was a missing pad to start. The white is silkscreen

[@utubebro748]

Good idea thanks👍👍👍👍

[@nikolatesla8114]

IC RIP!

[@joseluizbeling1789]

Show de bola, gostei muito. Tu, é o cara. Sucesso pra ti, e toda a tua Família também.

[@primus711]

yeah dont do anything this guy does that last part lol FFS guess you dont care about dwell times and trying to kill part and board and waste time

[@DwiPrionodpmdecoration]

Jos gandos, kotos kotos nganti mbledos (from indonesia)