How to Remove the Shifter Knob on a 1999 thru 2004 Jeep Grand Cherokee & Fix Console Lights

  Рет қаралды 194,514

88MustangGT

88MustangGT

Күн бұрын

Пікірлер
@dalesandford8774
@dalesandford8774 8 жыл бұрын
This was an excellent video - and very helpful to my son and I this past weekend when we had to change out a broken shifter bezel. Only input that I would have - I could not get the larger knob off (common problem). I am 50+, and an accountant.. -so simply do not have the strength to pull it off - regardless of the position that I took in the vehicle. In the end, we used leverage - by taking two 8 foot 2X2 boards off the scrap pile, and nailing a short 2X4 block in the middle. We wedged it around the base of the knob. I placed some blocks on the drivers side (the seats have too much give) and he pulled up on other side (out through the passenger side door). I jiggled the top of the knob as he increased pressure - and voila - it popped off!! Again - great video Jeff and much appreciated!!
@alejandroezequiel265
@alejandroezequiel265 3 жыл бұрын
you prolly dont care but if you're stoned like me atm you can watch all of the new movies and series on InstaFlixxer. I've been watching with my girlfriend lately =)
@owenduncan760
@owenduncan760 3 жыл бұрын
@Alejandro Ezequiel Yup, have been using InstaFlixxer for years myself :D
@Apollyon67
@Apollyon67 Жыл бұрын
8 years later and still helping with this video. Thank you.
@88MustangGT
@88MustangGT Жыл бұрын
Glad it helped!
@pratherat
@pratherat 7 жыл бұрын
I just removed the shift knob from my 2002 Grand Cherokee in a surprisingly easy way. After removing the center console: 1) Cut a notch in the end of a 2x4 slightly larger than the neck of the shift knob. Shift to "Drive" so the knob points straight up, then use the forked lever you just made against a fulcrum of scrap lumber, and the knob will pop right off. It's a good idea to protect the knob with some padding like an old cleaning rag. 2) Instead of cutting wires, remove the contacts from the plug. Disconnect the plug, then use a small flat tip screwdriver to gently pry up a small rectangular piece on the outside of the plug (some sort of locking gizmo) about a millimeter or two. Meanwhile, with an even smaller flat tip, push back the locking tab inside the plug socket and gently tug the wire. The wire and contact should slide right out, intact and ready to be reinserted later.
@jeepercreepers54
@jeepercreepers54 Жыл бұрын
Don't replace with another used Jeep part. I bought a green led light strip the same length as the original piece, wired it up and attached with 3m double sided tape. Not the Amazon chinese counterfeit stuff. Works beautifully and bright. Has lasted for years.
@charliedee9276
@charliedee9276 4 жыл бұрын
I changed out the shifter when I swapped transfer cases on my 04 from the Quadra Drive to the Select Trac, when I pulled the console I found a couple of roaches in there and one unlit fat joint. Glad I found them and not the fuzz dogs.. ( I just bought this recently)
@MasterPKW
@MasterPKW 8 жыл бұрын
Хоть один человек показал как снимаются ручки кулисы КПП. Спасибо!!!
@Sgyozo
@Sgyozo Жыл бұрын
Came to see how to remove the knobs for another reason, now i know it should be lit, damn... :D
@davidandujar9757
@davidandujar9757 4 жыл бұрын
What are those flaps that you said you clean called because I need to replace mine
@DL-by8el
@DL-by8el 4 жыл бұрын
I can't get any shifter off at u pull it, the wires have a tab inside the connector. You dont have to cut them. Good video!
@88MustangGT
@88MustangGT 4 жыл бұрын
kzbin.info/www/bejne/i5uwnXaJoamsrJI - check out this youtube video (Removing Jeep Grand Cherokee knobs - Kaido Roosipuu) - use channel locks or vice grips, pry bar & a cloth to keep from damaging shifter stem -
@mikemikemikemikemikemeup
@mikemikemikemikemikemeup 4 жыл бұрын
What does the wire do? I would like to know so I can make a custom shift work. Is it just the over drive?
@jermainebrown3457
@jermainebrown3457 25 күн бұрын
This is a good video. This is for 99-04 jeep Cherokee.
@rlchick5774
@rlchick5774 4 жыл бұрын
Thank you can I do this with an 04. Was a U Pull it today glad I waited to do it as I didn't know I was missing a light. Another thing to add to my list. Seems like there should be a way to remove that wire. Maybe the shaft can be unscrewed. As a lady I hope I have the strength to pull the shifters. Thank you so much I want to replace my radio too.
@88MustangGT
@88MustangGT 4 жыл бұрын
Hi RL Chick: I think the 99 thru 04 cherokee's are similar - pull that part from you-pull & pay, LKQ, ect. and give it a try!
@rlchick5774
@rlchick5774 4 жыл бұрын
@@88MustangGT Found that you don't have to clip the wire. In the white connector the red wires can be removed by pushing on a small clip with something the size of a fork prong.
@88MustangGT
@88MustangGT 4 жыл бұрын
Sounds like you are making good progress working on your Grand Cherokee - changing out the radio is not to difficult & units can still be found at "you pull & pay or LKQ."
@rafael661kc
@rafael661kc 4 жыл бұрын
Oh my Jesus thank you for this video mines went out definitely gonna replace it now
@safutos
@safutos 4 жыл бұрын
how do you know the strip worked before you take it off the donor vehicle?
@88MustangGT
@88MustangGT 4 жыл бұрын
No way to test the "electroluminescent strip" that I know of - take your chances! Pulled mine from a local "you pull & pay" junkyard. It worked and is still shining like new almost 6 years later.
@JVIMTM
@JVIMTM 5 жыл бұрын
Nice video.any idea how to fix the squeeks from the center armrest console?
@rcaive0875
@rcaive0875 2 жыл бұрын
How do I remove the rear cupholders?
@88MustangGT
@88MustangGT Жыл бұрын
Pull up & out - you can do!
@epicvibration1759
@epicvibration1759 4 жыл бұрын
Thanks for the breakdown. Seems like this will work for my 2000 v8. To the pull and pay tomorrow!
@88MustangGT
@88MustangGT 4 жыл бұрын
I think 99 thru 04 are similar - hope it lights up for you are finished - good luck!
@epicvibration1759
@epicvibration1759 4 жыл бұрын
Jeff Palmer thanks!
@AA-zm4ow
@AA-zm4ow 3 жыл бұрын
doing the hard way , you can use a towel hammer. to beat to one side then the other must be in 4low then beat upwards from down the pedals off it goes , or using pliers and a small pry bar like other videos or a wrench as a pry bar,, the gear shifter also can be taken off that way or taking out button cover n button with a small screw driver bottom first,cutting wire for over drive with razor blade by prying on line of vinyl first , then pry out top first then bottom using vise cribs , is the easy fast way without taking out the middle bezel etc console a rest area
@88MustangGT
@88MustangGT 2 жыл бұрын
Saw others using wrench and pry bar method after I made this video. Much easier doing it that way. Live and learn!
@agontop1
@agontop1 8 жыл бұрын
Been fotsin around with the main knob for almost an hour now and nothing, my patience is wearing thin. I'm almost about to just hack saw right thru the dam thing!!! Any suggestions?!!
@dondiaa6377
@dondiaa6377 7 жыл бұрын
hey Jeff , thank you for your video , when am bulling the knobs i forget the wires and they got cut so how to fix that ?
@GodsSignPost777
@GodsSignPost777 5 жыл бұрын
Hey Jeff, what were the two green wires for? I don't have them on my 2001 JGC Laredo
@gustavobanharadorettopadov9920
@gustavobanharadorettopadov9920 3 жыл бұрын
Man you really help me, thank you!
@88MustangGT
@88MustangGT 2 жыл бұрын
Thanks Gus, this is my most viewed video (over 170,000 views). Never thought it do that good. ps my lights when out a couple year again and remained to since. Jeep is getting old and don't feel like messing with it again. Still runs great anyway.
@LtGIR
@LtGIR 7 жыл бұрын
Getting ready to swap transfer cases so I have 2wd and was looking to swap shift indicator as well, that's way too much work compared to older rigs. I'll just go the sticker route I think. Thanks!
@88MustangGT
@88MustangGT 10 жыл бұрын
Fixing the console lights in my 02 Jeep Grand Cherokee
@patrickholt3255
@patrickholt3255 10 жыл бұрын
Thank you for your video. Question for you my lights are also out but they come on sometimes it's there a way to test and see why. I thought lose connection but I can't find any
@88MustangGT
@88MustangGT 10 жыл бұрын
My console lights would work sometimes just like you describe. You need to find a local "you pull & pay" junk yard and replace that part as shown in the video. Good luck. Thanks for commenting.
@itsahalmar1853
@itsahalmar1853 2 жыл бұрын
Heck yea thanks for the tour.
@88MustangGT
@88MustangGT Жыл бұрын
No problem 👍
@thomasalbers4323
@thomasalbers4323 4 жыл бұрын
Thanx for the video... Help out a lot.
@88MustangGT
@88MustangGT 4 жыл бұрын
TA - glad to help out!!! Subscribe to my channel for lots of Fox Body Mustang content. Thanks
@airamsuarezgmail
@airamsuarezgmail 10 жыл бұрын
Thanks great video, what is the number part and where you found for replacing in my jeep
@88MustangGT
@88MustangGT 10 жыл бұрын
find a local "you pull & pay" junk yard - look for 1999 thru 2004 Grand Cherokee (pull from the newest Cherokee you can find) - good luck
@shanekelly9810
@shanekelly9810 8 жыл бұрын
Your oil pressure looks pretty high, did that ever end up being a problem? Mine is always a tick over the halfway point... I've always wondered what happens if it's way over.
@88MustangGT
@88MustangGT 8 жыл бұрын
oil pressure has never been a problem - this Cherokee runs great -
@gregww101
@gregww101 9 жыл бұрын
These things are really on there! Holy balls.
@88MustangGT
@88MustangGT 4 жыл бұрын
The shift knobs are on there tight. Just pull up hard and wiggle knob & it will come off.
@mikepalmer9379
@mikepalmer9379 9 жыл бұрын
Wow. Great video. Thanks for posting. I realize it's doable, but it still seems like a lot of work just to get the PRND12 lit again. It's a "nice to have", not a "need to have". So much simpler on other Jeep models, from what I've seen. To have to tear out the entire middle assembly just to replace a light seems extreme. I love my 2004 JGC. With 170K on the odometer and everything running well, I'm dealing with a lot of these ticky tack issues now. I also need to replace a PC74 behind my climate control. Since you've already done this gear shift strip once, and we're obviously related (Palmer), what say you drive up to Michigan and take care of this for me? Ha ha.
@maninthevan53
@maninthevan53 10 жыл бұрын
o wow I thought I had some blown bulbs on mine never new it is a full system (1999) thanks for the video
@88MustangGT
@88MustangGT 10 жыл бұрын
you should be able to find this part at a junkyard (u pull & pay - ect) not a difficult repair - good luck - thanks for the comment!
@urielbenavides7596
@urielbenavides7596 10 жыл бұрын
What if I wanna just change the shift knobs so I can put some cool ones on
@Leo-lr4eq
@Leo-lr4eq 6 жыл бұрын
last revenge that's one thing for a stick shift, but an automatic?
@88MustangGT
@88MustangGT Ай бұрын
"Big day today as we’re about to hit 10,000 subscribers! 🚀 Thank you all for being part of this incredible journey with 88MustanGT. The best is yet to come-stay tuned and let’s keep growing together! 🙌🔥"
@Zombi3Rag3
@Zombi3Rag3 7 жыл бұрын
Where can I find the center console part as well as the part you replaced? Are the online?
@88MustangGT
@88MustangGT 7 жыл бұрын
Austin Hammond - check out your local "pull & pay" junk yard
@MrStatic101
@MrStatic101 9 жыл бұрын
Pretty awesome video man!
@JoeKacmarik
@JoeKacmarik 8 жыл бұрын
Nice video thanks!
@carlos.f.2400
@carlos.f.2400 6 жыл бұрын
What I did to mine I put a green LED strip.
@rodolfomacariopalacios649
@rodolfomacariopalacios649 4 жыл бұрын
esa fue la mejor idea, felicidades
@grantimages22075
@grantimages22075 10 жыл бұрын
great video helped out alot
@oscardaone
@oscardaone 8 жыл бұрын
I will take notes.
@wjack90
@wjack90 2 ай бұрын
Damn, that a lot of work 😫
@Maxxis1941
@Maxxis1941 Жыл бұрын
Title says Cherokee but first seconds of vid say Grand Cherokee. Are you confused about which Jeep you own? 😳
@88MustangGT
@88MustangGT Жыл бұрын
Grand Cherokee Laredo 4.7 V-8 non HO 230 HP
@ybor363
@ybor363 10 жыл бұрын
1:55 I saw that coming.
@prrra33
@prrra33 9 жыл бұрын
My 4x4 shit knob dont come off like yours i bee. Tugging like a mad man
@Teebar555
@Teebar555 7 жыл бұрын
Thanks, I have the same issue
@gristlevonraben
@gristlevonraben 9 жыл бұрын
thanks for posting.
@thedogzoo
@thedogzoo 8 жыл бұрын
Thanks.
@sandspritpark
@sandspritpark 9 жыл бұрын
Electroluminescent it's called
@88MustangGT
@88MustangGT 9 жыл бұрын
thanks for the info
@88MustangGT
@88MustangGT 4 жыл бұрын
kzbin.info/www/bejne/i5uwnXaJoamsrJI - check out this video!
@TheSnup23
@TheSnup23 6 жыл бұрын
Еще бы по русски говорил, цены бы тебе не было! Still I spoke Russian, the prices would not you be!
How to Fix Death Wobble 99-04 Jeep Grand Cherokee WJ
13:25
martinbuilt
Рет қаралды 202 М.
Jeep WJ Shifter Bezel Removal
16:13
v8jofes
Рет қаралды 34 М.
The evil clown plays a prank on the angel
00:39
超人夫妇
Рет қаралды 53 МЛН
Top 5 Problems Jeep Grand Cherokee SUV 2nd Generation 1999-2004
10:45
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 434 М.
The steps it take to replace your radio, Jeep Grand Cherokee
14:21
Five Star Car Stereo
Рет қаралды 177 М.
Bigger Engine.
2:03:51
SimonFordman
Рет қаралды 212 М.
Jeep Grand Cherokee Stereo/Deck/Radio Install (1999-2004)
15:06
Tony The Truck Guy
Рет қаралды 463 М.
Replacing Bulbs in Climate Control 1999-2004 Jeep Grand Cherokee
21:37
How to Easily Fix a Jeep Gear Shifter Backlight
7:25
A_Hobby_with_wheels
Рет қаралды 79 М.
Part 1, 1999-2004 Jeep Grand Cherokee Dashboard Removal
9:58
Dr. Bob's Last Chance Garage
Рет қаралды 455 М.
How to remove center console Jeep ZJ
3:48
Wisc0n J0rd0n
Рет қаралды 22 М.