How to repair and do maintenance to the 12V compressor

[@derivas007]

please more video like this for this compressor!for example how to detect and fix a problem on this unit

[@TuxingCN]

We have manul instructions in detail, and you can ask from our seller. Thank you

[@angerjamir575]

Very helpful video Thank you

[@tfphyrex]

Mein kompressor zeigt den aktuellen druck nichts an. Was kann ich tun?

[@sergeiballer6021]

Hi ,what kind of lubricant do you use when assembling the piston?

[@TheXaelem]

100% silicone oil. Read the manual ffs

[@antoniocarvalho365]

Does this compressor have to be oiled through the brass grommet on the cooling fan side of the compressor located just above the top left corner of the cooling fan after so many fills? I have the TXET062 and it looks similar to the nomad which has an identical brass grommet.

[@visamedic]

LITERALLY my compressor just got delivered 10 min ago. Between this video and the one Brothers in Air did, I think I’ve got this covered. Off to do yard work then maybe some target practice this evening. 😁👍

[@TuxingCN]

Haha, enjoy it, my dear good friend!

[@leviathan216]

How often should the O-rings be changed please?

[@keesdane9687]

This compressor need oil?

[@petesherman1889]

Is there a repair kit we can buy that contains the orings and needed materials to complete this job?

[@TuxingCN]

Of course, we are the direct factory, and we can provide all accessories you want. Do remember direct factory is the best cooperation partner

[@rahmanazhary5774]

Oermasalahan yg sering terjadi pada kompresor jenis ini adalah poros as motor sering patah, itu yg saya prihatinkan.

[@ประจักษ์พรพิมลกุล-ภ1ง]

สั่งซื้อได้ทางไหนครับ ราคาครับ

[@cnuch235]

Sir i need your help. Where can i get its o rings and repair kit. Already i bought this compressor from my local gun store but they don't keep service kit. Please let me know where can i get

[@TuxingCN]

tuxing.aliexpress.com/store/2653128 you can get all kinds of accessories you want here

[@cnuch235]

@@TuxingCN is there any another website to purchase those piston rings

[@TuxingCN]

@@cnuch235 www.tuxingcn.com

[@kj5905]

Do you sell the two ring stretchers? Where do I buy those?

[@truthspeaker2062]

What is the difference between txet061 and txet062 . And which is better .

[@keithvelcr805]

Hello Sir,the TXET061 is external converter and TXET062 is internal converter,this is their only differernt,they are nice.

[@deanmarkham9145]

What are the two lubricants that you used?

[@dalesmith3015]

I had the same question. I notice no one is answering questions on this video.

[@JimmyMakingitwork]

Use only high pressure lubricants, like pure silicone or teflon grease or oils. Never use motor oil style lubricants, they’re flammable at high pressure.

[@JimmyMakingitwork]

How can you buy parts? I have a cracked line in one I just bought on Amazon. The coiled line inside leaks from the crack and it won’t build pressure, brand new first use, doesn’t work.

[@TuxingCN]

tuxing.aliexpress.com/store/2653128 Ask the sales here, they will help you

[@malcolmbaker3801]

Where do you get the spares

[@stevenrowe5047]

thank you for your time I am going for it.

[@reddyksl7213]

I just got my brand new compressor, the problem is it build pressure some times and it won't some time. very strange behavior. Since it's building pressure , I don't think it's issue of Orings or any leakages. What should I check for ? .

[@TuxingCN]

Check 9:50 this check valve is clean and in the right directions.

Hello, how do you change the cotton filter into the black cylinder ?? You don't do it but it is written in the manual ... Thanks, regards.

[@dalesmith3015]

I just removed the large nut on the top of the canister. I used a curved hook to pull the filter out. Take notice of how far down the filter is from the top of the opening and when replacing try to put it close to the same depth. I don't know if the depth is important, I'm just saying that is what I did.

[@TuxingCN]

Hello, dear friend, Just removed the large nut on the top of the canister

[@emilbaligod1935]

@@TuxingCN The new models have no more canister for the lowpressure

[@karlortiz7911]

Can i use it for scba self contained breathing apparatus??

[@ElTiradorSelectoACE250173]

Buen tutorial 👍💯

[@komrad40]

I am getting Error E2 on LED display. Its a long single beep and then error E2. Any suggestions please? Thank you.

[@johanthaens5531]

Nice video! Any advice on the kind of lubricants that should be used?

[@TuxingCN]

treadmill lubricants oil

[@harzoglups]

Nice video! How often is this full maintenance supposed to be done?

[@TuxingCN]

We suggest after fill 40 bottles of 0.5L air bottle, we need to maintenance it.

[@silviu74]

Hi Tuxing CN , what’s the time interval to put silicone oil and how can I put in ? I just received my order from your store from AliExpress and I want to know if compressor have silicon oil or not from the beginning! Thank you 🙏

[@TuxingCN]

Hello, thank you for your order. Locate the lubrication hole on the left hand side of the unit. Using any silicon oil, like 100% treadmill oil, apply 2-3 drops of silicone oil every 5 fills or1.5 hours of use (whichever comes first). It has silicon oil inside at the beginning. Thank you and have a nice day!

[@keesdane9687]

Can you show me where the oil need to go in

[@maragod2905]

Hello, my compressor loads up to 10 bar and then the fuse burns, I change it but it can't go any higher and the fuse burns again. what could be the problem

[@keithvelcr805]

Hello Mara,good day,maybe somewhere is airleak,you can check it carefully.

[@HenriqueSilva-gm4qb]

I need rings for maintenance of my compressor. In Brazil I can't find one to buy. Do you sell to me in Brazil ?? Where to buy?

[@TuxingCN]

Add whatsapp: [phone] we will let you know how to better maintenance your compressor. Thank you for your attention

[@TuxingCN]

Contact whatsapp [phone]

[@ke6bnl]

can you get the compression ring expanders.? if not can you give the upper and lower diameters and length of the tool so I can make one.

[@TuxingCN]

1.1cm lower diameters *3.6cm length, The upper diameters is not so important, it just can make the orings inside it.

[@au1639]

@@TuxingCN I see two white tapered cone expanders, what are the diameters of the one not identified in above reply?

[@saadmagnum936]

How do you open the bleed valve setup

[@TuxingCN]

open and fasten it by hand directly

[@corneliuswowbagger]

Would someone from Tuxing CN list the silicon grease and silicon lubricant used in this video, thank-you! Also, do you have rebuild kits with o-rings, gaskets, etc. or the exact sizes needed.

[@TuxingCN]

As long as you use 100% silicone oil. Many people use treadmill 100% silicone oil Thanks

[@corneliuswowbagger]

@@TuxingCN I will pick up some silicone oil and grease. Thank-you!

[@maragod2905]

Hola mi compresor llega hasta 15 bar y luego se para y se quema el fusible, que podria ser, existe algun sello de precion

[@kernalmusterd]

is that a inturnal moisture filter do you need to replace cotton felt if there is one inside

[@TuxingCN]

In order to make us get very good quality air, we installed one filter inside ( We think other suppliers seldom do like us), we need to replace the cotton after long usage. Such as fill 20~30 times 0.5L gas cylinder from 0- 30Mpa

[@АлексейОрлов-ц4д]

Почему нет гарантии,если покупаешь на Али экспресс??Можете помочь с гарантией?

[@keithvelcr805]

All the TUXING compressor,it has one year warranty.

[@derivas007]

GREAT TO SEE

[@truthspeaker2062]

I thought it was a squid game . Thanks god it is just a tuxing review

[@rinopravato1285]

gracias

[@WillemLuntungan]

Mantappp

[@maragod2905]

121 / 5000 Resultados de traducción Hello, my compressor reaches 15 bar and then it stops and the fuse burns, which could be, there is a pressure seal

[@TuxingCN]

Maybe your tronsfomrer/Conventer is not connect well, make it burn. Repalce the fuse from packing list and make sure the imput voltage is 12V at the same time

[@leonardoangelini328]

It doesn't charge anymore, but the compressor is new... What could have happened...?

[@TuxingCN]

Make sure not any air leaking, especially between every adaptors. Remember to close the air release screw. Contact : [e-mail]

[@علي.العبودي....2]

😍😍💕💕

[@Bruxa-do-71]

Olá amigo estou com pobrema com o meu compressor, está com vazamento pelo suspiro

[@TuxingCN]

Fasten all the connections, if you need other helps, contact the seller. I am pretty sure she will tell you how to do.

[@Sledus]

Спасибо! Но не понятно! Это нужно каждый компрессор после покупки - разобрать и удалить смазку???

[@keithvelcr805]

Вы можете сказать нам, где вы не понимаете, мы дадим вам подробный

[@ord959]

Инструкция по разборке и ремонту 👍

[@Sledus]

@@ord959 Спасибо!!

[@sergeiballer6021]

Скажите пож,какую смазку используете при сборке поршневой?спасибо!

[@Sledus]

@@sergeiballer6021 Внутрь механизма закладывал голубую смазку для авто покупал. И перед каждым запуском компрессора в отверстие забора воздуха капаю жидкую силиконовую смазку. То есть в поршневую попадает жидкий силикон. Можно наверное смазку которая в пневмоинструменте используется. Я еще хитрю - когда включа. от 220 вольт то к отверстию забора воздуха ставлю блок питания (а в нем так же вентиляторо и через него прогоняется воздух. Этот воздух уже под давелние идет и попадает в сам компрессор. Так у меня температура где то 55-60 максимум. Больше не поднимается.

[@palioxaraktirasmr.7484]

Nice video, but it is super hard for a normal person to do it alone.

[@bobbythompson3544]

The whole air supply thing is out of hand, I paid £10 for three litres of air! By dive shop!

[@TuxingCN]

12v compressor is suit for filling under 0.5L fasten every connections, it will avoid the air leaking

[@АлексейОрлов-ц4д]

Ужасное качество компрессора!!Сломался через месяц использования.Гарантии нет,покупал на Али экспресс! Продавец сказал,что все запчасти надо покупать за свой счёт.

[@ord959]

Я написал продавцу дважды и дважды он мне помог с запчастями абсолютно бесплатно в рамках гарантийного ремонта. Гарантия 1 год. Качество соответствует стоимости. Дешевле компрессоров нет.

[@ord959]

Набор запчастей для полного обслуживания стоит около 10$. При минимальном слесарном инструменте и опыте, за пару часов он полностью обслуживается или ремонтируется. Главное чтоб двигатель был целый и электроника, а остальное все не дорогое и легкозаменимое.

[@marklange1614]

I hate this Compressor!! Problems all the time

[@gibawatts]

The nails 🤢