How to replace Bell & Howell 456A Projector Drive Belt. Projector goes backwards in reverse, but won't go forward. This DIY video shows how to fix this problem. Projector supplies at www.TvedenLampModules.com
Пікірлер: 36
@dwayneoxford97193 жыл бұрын
Thanx for your videos. Bought a B&H 256 in working order for $25 today at flea mkt. Few videos on them, trial and erred the back case off, learned to leave the 4 lower screws alone. Need counsel on lubing gears and motor.
@hardluckcharlie3 жыл бұрын
I use a clear silicone grease for the gears and small electric motor oil for the little brass pillow block bearings and the motor. These you can get at your local hardware store. You don't need but a few drops of oil and a light coat of grease. Don't forget to grease the Shutter wheel/ claw cam. I have video on this also. I'll see if I can find the link. Thank you!
@dwayneoxford97193 жыл бұрын
Thanx @@hardluckcharlie. Do you clean off old lube or just add? This it? kzbin.info/www/bejne/fnLRYn2Pfaikfrs
@thisweekinfilmpodcast8 жыл бұрын
Great video. Borrowed same projector from a friend and the motor would run but nothing would move. Looks like it's the belt. Once it comes in the mail, I'll be back to watch this again!
@hardluckcharlie8 жыл бұрын
+This Week in Film Podcast Thank you so much for watching and commenting. Good luck!
@thisweekinfilmpodcast8 жыл бұрын
+hardluckcharlie question maybe you can answer. I did all the steps here and the belt was very loose. It's now replaced but the gears still do not spin. I've noticed .... Nevermind. I figured it out. I guess the gears haven't moved in so long the just needed a little "jump" once I moved them around a little bit the whole thing came back to life!
@mehstgful10 жыл бұрын
I appreciate seeing which screws to loosen in order to disassemble (for various reasons). Thanks
@RandyHunt9 жыл бұрын
Thanks for sharing. A friend gave me this projector today, and this is the problem!! Great instructions!
@brendabrown28188 жыл бұрын
great instructions .Your awsome
@kentsanders15264 жыл бұрын
Like your video what screwdrier using Thanks
@patriciarogosich22767 жыл бұрын
I am trying to repair a B&H 346A model with this problem. I'll post again if it works! *Fingers crossed*
@patriciarogosich22767 жыл бұрын
It worked!
@hardluckcharlie7 жыл бұрын
Great to hear positive results. Thank you Patricia!
@haslerconnie3598 Жыл бұрын
I have a 357 B - I took it apart as you suggested and the belt looked good but there was a lot of gunk in the gears etc. so I cleaned things up and and it seems to be working great - until I put on a reel of film. It feeds fine and catches and then it all stops turning. One time it continued great going fwd as long as the film was not on the receiving spool and was going to the floor. When I put it in reverse it struggled and just when I was about to give up, it started working and rewound properly onto the original spool. If feel like I'm soooo close. It's almost like the load of the film is too much for it to turn. I started with a 7" reel and then a 3" with the same results....All the feeding spools seem to be turning fine and the film doesn't seem to be caught up in the feeding system. I would very much appreciate your thoughts and suggestions...
@hardluckcharlie Жыл бұрын
99% of the time it's the belt that needs to be replaced. Even if they look good they can be a little stretched out. That is where I would start. www.ebay.com/itm/291686072152
@haslerconnie3598 Жыл бұрын
@@hardluckcharlie thank you... I ordered a belt. I noticed on your video there is "grease" on the wheels... since I did such a good job "cleaning" mine up (and it was all dried so I think it needed cleaning) do I need to put grease back on? what type? where do I put it?
@frangiul134 жыл бұрын
Great tutorial! Would you be able to do a tutorial on how to change the drive belt on a Bell & Howell Filmosonic 1731-1733 Super 8 sound projector? For the life of me I cannot figure out how to get the old belt off the pulleys.
@hardluckcharlie4 жыл бұрын
Great suggestion! I will make a point of it. Thank you!
@paulgaffney84376 жыл бұрын
Where can I purchase a drive belt for a Bell & Howell Projector?
@hardluckcharlie6 жыл бұрын
www.tvedenlampmodules.com
@jcgtv36922 жыл бұрын
is this belt the same as the B&H 471 projector?
@hardluckcharlie Жыл бұрын
Yes. Thank you for watching and commenting!
@tehurlburt16 жыл бұрын
My Bell & Howell 456A turns on and the light turns on, but the image projected is just a blob. Is there a way of focusing the image, or anything you can suggest to address this problem? thanks
@hardluckcharlie6 жыл бұрын
The blob is usually always from a "foggy" lens. Shop eBay for a clear lens. $20-30.
@tehurlburt16 жыл бұрын
hardluckcharlie Thanks for the reply! I removed the lenses and they seemed pretty clear, but a few of them were chipped at the edge (also not sure I replaced them in the right order). Could the chips be the problem?
@hardluckcharlie6 жыл бұрын
Well chips can be a problem for sure. But if you get the lens sequence incorrect that is a much more significant problem. I would consider a "new" used lens. But if you have the time to experiment, try putting them in a different order. Good luck!
@brendabrown28188 жыл бұрын
Where did you get the new belt and what size is it?
@BigH55008 жыл бұрын
He posted a link in the description..... www.TvedenLampModules.com as for the size, i dunno.
@kathythomas80525 жыл бұрын
I have an old Bell now projector and I'm trying to clean it up right now but it's got some kind of blue oil in the bottom of what is that and is it detrimental to it
@conanthedestroyer71235 жыл бұрын
I have a B&H 456A and replaced the rubber tire, and drive belt. It works much better now... however the picture it gives is horrible. I think something is missing like a shoe but not sure what parts are supposed to be there. The picture is very washed out with white light around the picture. I ran the same 8mm film on an older 1950's Regent 8mm projector and the picture is 10 times better with nice vibrant color. Please help! What is wrong with my B&H 456A?
@stephmaras8 жыл бұрын
Sorry if this is posted elsewhere, but what could be a reason why my Bell & Howell 456A projector suddenly won't run in reverse? The single frame advance knob spins, but the front reel head won't move. Thanks in advance.
@hardluckcharlie8 жыл бұрын
+stosh16 It's hard to tell without actually seeing it. But, it could be the drive belt has stretched. Or it could be the transmission mechanism attached to the drive tires needs adjusting. Check your belt first. We'll try to get a video up showing how to make simple adjustment to the drive tire mechanism. Thanks for writing.
@berky3228 жыл бұрын
What would cause it to not operate in reverse?
@hardluckcharlie8 жыл бұрын
Most likely the transmission tires need to be adjusted. I am producing another video that shows this procedure. Look for it here soon or on the website; www.tvedenlampmodules.com
@carolyokimcus59547 жыл бұрын
why doesn.t the film feed all the way? It starts feeding but then it backs up.
@hardluckcharlie7 жыл бұрын
The small rollers might need to be lubricated with WD-40. If they do not spin freely the film can get twisted and then snagged and backed up accordion style. Good luck!!!