How to Replace Broken Wheel Lug Nut on 2002 Honda Civic

In this video, I show you how to replace a 2002 Honda Civic Wheel Lug Nut Stud.
Just follow step by step shown on your screen a basic remedy.
Tools Needed:
.Wrench
.Hammer
.Angle Grinder Tool with Cutter Disc & Grinder Disc
Disclaimer Advise:
Don't do this on Newer Vehicle or Consent is must if so

[@AustinShockSS]

Thank for the tip. I used a dremel to do the same thing. Sucks you can’t pull the hub since it’s a single sealed unit. Honda should have left a slot or clearance to pull the stud out.

[@jambasicskills1970]

You're correct I can pull that hub but need some part to remove. I did this for rush job for this old car lol. Thanks for your comment

[@EdmundTarin]

Mickey Mouse, that’s the wrong way😂

[@jam_70]

wow 👌 cheapest way for old vehicles 👀

[@jambasicskills1970]

Don't do it with out knowing to do it lol🤔

[@jambasicskills1970]

Hello Everyone, This fixing is a complicated job to make. I just show this video not to encourage someone to do it on your own without knowledge for it. Need to have a proper tools to use. Appreciated much.. Thanks🤩

[@cristiangutierrez2172]

I want to do this for my Honda I only payed $300 for it and I need to get my winter tires on before it’s to late 😂

[@jambasicskills1970]

Don't let winter chase you, do it while still behind you

[@MiquelGorbiviUS]

honda sure makes these difficult. An easy job and they don't provide the space it. I have the same issue, I'm going to have to grind that section

[@jambasicskills1970]

That is the easy way and maybe cheapest way lol Thanks Bro

[@litsmixtv]

Watching master nice idea

[@jambasicskills1970]

Thank you! Cheers!

[@3d-rambler795]

F**d the job

[@tengzturiagaiii3185]

Mali po yan pag cutting nyo. Tanyo na sira pa yung part sa gilid at likod. Pwedi lang po yan pokpokin palabas sa likod.

[@jambasicskills1970]

Tama po kyo. Pag popokpokin nyo pwede pong masira ung center hub bearing at lalaki and gastos kaso dahil luma na po itong kotset pinakita ko na pwedeng e cut kaso dapat gagamit ng maliit na cutter disk at sinabi ko po na wag gagawin pag bago ang kotse or may nag pagawa lng po sa inyo tiyak magagalit hehe

[@tengzturiagaiii3185]

Sabagay may point kayo. Nag hanap po ako ng video pano alisin yang bali na stud. Wala madaming ganyan din po ang ginawa. Kesa mag baklas ka ng buong hub at wheel bearing. Which ang pangit ng desenyo ng honda sa kinalabasan ng ganyan. Kasi may ibang sasakyan po na sa likod gaya ng pinutulan nyo para mailabas ang bali na stud. May inukit o desenyong pwedi itulak palabas dun. Sorry po kung may nasabe akong mali sa unang mensahe ko.

[@jambasicskills1970]

@@tengzturiagaiii3185 Opo< kasi kung gusto nyong walang sira or cut ung likod tatanggalin mo ung center hub at possible na masisira sya kaya magiging doble gastos mo. ginagawa ko lng ito sa personal ko at lumang sasakyan, Salamat sa time po kabayan🙂

[@dailydad6335]

​@@jambasicskills1970 kuya na grinder nyo pala ung likod kasi 2hrs ako nag.ubos para lg matanggal ung luma kaya huminto muna ako sa sunod gawin ko ung ginawa nyo 2003 civic sakin

[@rusty-Shackleford]

i am professional obvious now let me take a grinder to your car

[@jambasicskills1970]

Yeah, I need a proper tools for it😁

[@cayansquest265]

Good Job Bro