How to replace/check 4WD switch of transfer case Pajero

In this video I'll be showing on how to replace the 5 switches of 4WD in the transfer case at the same time by checking and conforming the value of both the defective and brand new switch of Mitsubishi Pajero 4th Gen.
Music by; NEFFEX Title; home and Dangerous

[@AirfixLtd]

Thank you for sharing this valuable information along with your knowledge and guidance. 👏👍

[@rolexpanuncialman3484]

Your welcome Sir..

[@bulatnord743]

Super. Thank you helpeng!

[@surn0m]

awesome man thank you

[@abulfaiz8662]

Thanks for right way

[@fishyfishyal-hazazi4678]

Thanks alot 😘😍😘😍🇸🇦🇸🇦

[@time2kickarse]

Good video, get rid of the stupid music I would have much preferred you explaining the procedure and testing.

[@Hongzbengkelspesialismatic]

this video is very helpful, good luck always

[@TheShick95]

Which diagnosis software is in the begining of the video? seems pretty good for Mitsubishi cars

[@thesetruths1404]

Thanks. Now I understand how this system works. I've got a 2003 Montero Limited, 3.8L, 217,000 miles. I've also got the infamous Differential Lock orange blinking light that would come and go for months and eventually stayed, and DTC 33 when I read the codes by jumping pins 1 & 4 on the OBD2 plug and counting the blinks. I also had codes 34 and 35 but after swapping the Freewheel Clutch Solenoid and disconnecting the battery for 5 minutes, the 34/35 codes went away and only 33 remains...the center orange light blinking and no control of the system remain also. The ground cable on the transfer case is good. All device plugs, vacuum hoses and wires are connected, clean and tight. Voltage reads 10.8-volts from each of the switches' harnesses with the ignition key On. I'm trying to figure out which Transfer Position Switch(s) (1 thru 5) is actually bad, before dropping the t-case to swap all 5 of them out. I want to be sure something else is not the issue making it look as of the switches are bad, as I hate swapping parts and doing unnecessary labor. I'm suspicious because I know the clutch solenoids were bad because I tested them, but I doubt they went bad, plus a t-case switch also...as in simultaneously. Maybe so, maybe not. I have a test light probe and a digital voltmeter/ohmmeter. Is there a test procedure to test each switch before dropping the t-case and removing them to be sure it is a switch (or maybe two) and not another issue? Thanks!

[@rolexpanuncialman3484]

Good day sir.if you have a diagnostic tools you can identify which switch are mulfunction/defective.because there is always two switches working together all the shifting process.and you can identify also during shifting the 4wd at what gear shift the orange blinks then that is your faulty switch.for sure remove the switch and read the resistance then judgement is yours.

[@Mrveescuba]

Hi there thanks a lot for your very informative vid!! its time for my jero to change the actuators!!! do you think it is worth to change only the one that causing the center ligth to blink?? cause when its not blink i can select gear with no problems at all?? if i change only that im going mitsubishi ones!!but if i change all of them ill go for the after market,,mitsubishi is very expensive and i dont use 4x4,its just the ligth onnying me on the dash.otherwise not a problem to change it at all!!!if im correct i need to change the cd lock??

[@duyduy15]

Hi, thanks for helpful video Are 5 switch the same (NC switch)? Thank you!

[@AspirantVeeVee]

OMG, thank you so much for thios video!!, Question, is this the same for a 1999 Pajero IO 1.8L GDI? and do they use the same switches?

[@stevebeever3688]

What software are you using on the PC?

[@nabilel-saheli9104]

hello ! great video ! please i have a question. on my pajero i can switch between all 2h, 4h etc etc… but i have two issues : 1 - when driving on highway, after a certain time (in 2h). the center light blinks orange ans the others disappear. all returns to normal when car is switched off and on. 2 - when i change from 2h to 4h, all 4 lights are green but going rear i can hear a clunk as if something is not engaging or disengaging well. i plan to change solenoids. no error on scanner for engine or gearbox

[@rolexpanuncialman3484]

hello sir..I hope this will help you..so no DTC found on your scanner that means your transfer swicth are good.now try to check your freewheel valve and freewheel swicth in your scanner if both are working properly,showing only (ON and OFF position)then your actuator,hoses and vacuum if still connected in your manifold.

[@leewilson2719]

Great video how far did you have to drop the gear box

[@rolexpanuncialman3484]

As far that your both hands can move/work comportable sir.because you need to prevent not to disalign the exhaust pipe.and other connecting parts of the engine.thanks.

[@wawaysabanal1644]

How to test know sensor is damage?

[@lolodavid100]

Hi i saw your post, are a mechanic who can work on my Pajero? I have the same problem

[@cresaldobantilan884]

What is the symptoms if the car needs to check this or replace what can we experience...while driving?thanks

[@rolexpanuncialman3484]

Your center diff.always blink the orange color Sir. then if you're using diagnostic tool, your DTC should be T/F position SW3

[@sulthanibrahimrajakhan9372]

Hello, thanks for the video... I have a problem with my mitsubishi pajero 2016 transmission... When I select 2H, instead of two rear green lights glowing, three green lights are glowing!!! However when I select 4H, all four green lights are glowing normally... Please help me with this... I changed a couple of times between 2H and 4H while driving around 60 kmph ( but I didn't change to 4HLc or 4 LLc while driving),then only this problem started!!!

[@rolexpanuncialman3484]

1st check all the vacuum hose from solenoid valve to actuator underneath may be there is a tiny holes.sir.

[@sulthanibrahimrajakhan9372]

@@rolexpanuncialman3484 thanks for your support

[@bushnut8305]

Is it possible to put switches in the wrong location. If so what would happen.?

[@rolexpanuncialman3484]

No sir..Each switch have their own individual color for location and identification and signal.

[@jesscapiral9978]

Gud pm San po shop nyo

[@devusvlogs8955]

Hai i have pajero . i have one problem , running after 24 km that central light light is blinking and some times after 10km . why like this do you have any idea please help me.

[@rolexpanuncialman3484]

you mean the color orange ?it will blinks only if you use 4WD.that means you have defective switches like shown in this video.

[@user-sz1yx4yj3z]

Отличгая информация, однако не понятно какое же должно быть сопротивление датчика?

[@MMCTUNING]

Близко к К.З.

[@Fireneedsair]

Did u do oem or after market?

[@rolexpanuncialman3484]

OEM sir

[@rolexpanuncialman3484]

OEM Sir

[@Fireneedsair]

@@rolexpanuncialman3484 can't afford those

[@MMCTUNING]

Спасибо за видео! Может кому будет полезно "Pajero4 НЕИСПРАВНОСТИ РАЗДАТКИ SS4 II "kzbin.info/www/bejne/q3KmdKiercSsrpo

[@andrewrobinson2869]

Hi i have a 2002 pajero i0. But it will not go in tyo low gear 4wd. Would this be same issue

[@time2kickarse]

Hi Andrew, I have a similar issue however all the 4wd system works while using the transfer case lever I put it down to a faulty switch. I'll test them all to single out the faulty one.