How To Replace Mercedes Rear Air Suspension Bags on GL Class X164 Chassis | GL450 Air Spring

How To Replace Mercedes Rear Air Suspension Bags on GL Class X164 Chassis | GL450 Air Spring
#HarjinderSidhu #MercedesAirBag #AirSuspensionBags #SidhuDIY #gl450
🙏 Shop online at Amazon - www.amazon.com...
Any Amazon Link in my description is an affiliate link. “As an Amazon Associate, I earn from qualifying purchases.” I would greatly appreciate it if you considered supporting my channel while shopping from the Amazon store by buying anything you needed from Amazon after clicking on one of the links. This gives me a small commission at no additional cost to you and helps me continue producing more videos! Thanks a million for your support!!🙏
Year Model: 2007 Mercedes GL450 (This procedure will be the same from 2007-2012)
Air Suspension Bag Rear w/o ADS for Mercedes ML GL Class fits A-2596 1643200225 - amzn.to/2qYUBOX
Mercedes Air Suspensions Shocks Mercedes Air Spring Bags Fit REAR W164 GL/ML 320 350 450 500 550 PAIR - amzn.to/2rCh2tZ
Front Air Shock Absorber Suspension Air Spring Strut Fit For Mercedes Benz W164 ML GL Class WITHOUT ADS - Single - amzn.to/2rWVowY
Rear Air Spring Bags Airbag Suspension for 2005-2015 Mercedes X164 W164 GL-Class GL320 GL350 GL450 GL550/ ML-CLASS ML320 ML350 ML450 ML500 ML550 ML63 AMG - amzn.to/3akxUHS
amzn.to/34N3aOF
amzn.to/3annp6J
Airbag - amzn.to/2xKe8bs
Suspension Air Bag Clip Rear Upper L+R - amzn.to/3etmdC9
Metric Hex Wrench Bit Socket Sets - amzn.to/2qiIskt
101-piece Socket Wrench Set with 3/8 and 1/4 Inch Drive Quick-Release Ratchet - amzn.to/2qmtnxu
Microfiber Cleaning Cloth - 24 Pack - amzn.to/2qZ2jZa
Black/Red Fast Lift Service Jack - 3.5 Ton Capacity - amzn.to/2rjEVqs
Jack Stands - 3 Ton, 1 pair - amzn.to/2qiMSIg
Heavy Duty Wheel Chocks, Set of 2 - amzn.to/2qmb8IO
Thanks for watching, Enjoy, and please don't forget to: LIKE, COMMENT, FAVORITE, SHARE and SUBSCRIBE. ”GIVE THIS VIDEO A THUMBS UP"
Please SUBSCRIBE, If you haven't done so yet, take a look around. If you like what you see be sure to Subscribe to be notified when new content is posted. Thanks again for visiting!
Easy Steps - easysteps.jimdo...
{This video is for educational purposes only, I am NOT a "Professional Licensed/Certified Mechanic" or "Professional Licensed/Certified Technician" and I am not liable/Responsible in any way for damages caused to YOU or your "Vehicle" or "Computer/Phone" due to this video}. Please leave your comments below if you have any questions or concerns. I hope this helps someone out there. Cheers!
*Disclaimer - Background Music "Alan Walker - Fade" (NCS Release)
**Disclaimer: All information is for educational purposes only and is the personal view of the author.

[@EasySteps_Sidhu]

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my 2nd channel, thanks in advance.🙌 🙏 🙌 kzbin.info

[@markojokanovic349]

This is literally simplified for an IQ60 person to do on it's own. Masterclass! Well done and Thank you! I'm about to do the same on my GL350

[@EasySteps_Sidhu]

You are most welcome, Thanks for the visit. Glad I could help! please share, thanks.🙏 Thanks for the like and thanks for watching.🙏

[@arashfarahani8357]

bro no words 3 minute video saved me so much trouble and money god bless man

[@elmundo1871]

I just completed the swap on my GL450. The success and initiation was due to your video, so thank you.

[@EasySteps_Sidhu]

Nice work! Glad it helped 🙏 thanks for the visit. Please share, thanks.🙏 Thanks for the like and thanks for watching.🙏

[@paulyancey68]

Do not remove fitting!!!!!!! (On the new bag) Arnott and most others have the "quick connect fitting", ....if you remove the fitting it will void warranty ....check instruction sheet first....also on mine i did not have to remove level sensor... It compressed and slid out with just enough room and also worked putting new one in...just some fyi...good to the point video 👍

[@EasySteps_Sidhu]

Thanks for sharing good points. Thanks for watching.

[@EasySteps_Sidhu]

I have started posting DIY videos on my other channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my other channel, thanks in advance. kzbin.info

[@johnliujr.5644]

Following this video, I did mine on a x166 in 3 minutes and 56 seconds as well (very similar). Thank you!!! 👍👍👍

[@EasySteps_Sidhu]

Fantastic! So nice of you. You are most welcome. Glad it helped. Great to hear!👍👍. Thank you so much for the like and thanks for watching.🙏🙌

[@EasySteps_Sidhu]

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 kzbin.info

[@NigelMarston]

Great explanation. Thanks for posting this. Made slightly more difficult for me because I wasn't comfortable working underneath the car - damn heavy ol' girl although your instruction to put the wheel underneath is absolutely right on. The airline nut didn't want to loosen for me so I squirted some release agent onto it and then it came loose. The flange underneath the airline nut made access with a spanner awkward but I managed in the end. I have a pair of Arnott airbags on order now.

[@EasySteps_Sidhu]

You are most welcome, thanks for sharing great feedback, it really makes my day. Thanks, glad to help. Thank you so much for the like and thanks for watching.🙏🙌

[@EasySteps_Sidhu]

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my 2nd channel, thanks in advance.🙌 🙏 🙌 kzbin.info

[@rickc1124]

Easy Steps Thank you so much for your video. I would like to donate if you have a PayPal account. We own a GL550 and our entire air ride system failed a week ago. There are a few things we need help on so I would like to at least contribute and make a donations to help encourage you.

[@EasySteps_Sidhu]

@@rickc1124 Thank you so much, I really appreciate it. www.paypal.me/SupportEasySteps Thanks again for supporting @Easy Steps.

[@apcfiltrationinc.1374]

Great video. Saved me a ton of money compared to what MB wanted for this change.

[@EasySteps_Sidhu]

Great to hear! Please share, thanks.🙏 Thanks for the like and thanks for watching,.🙏

[@archiij1707]

im in the same boat, they want mortgage payment for the chamge of both rears.

[@vladislav3]

Best, quickest video of this process. Thanks man!

[@EasySteps_Sidhu]

You're welcome! Glad you liked it!! Thank you so much for the like and thanks for watching.🙏

[@eltonstourandtrekking]

Thanks for the video.. Gonna do the same repair on my ML in just a few days. Cheers from Norway!

[@EasySteps_Sidhu]

Good luck with your DIY project.👍 Most welcome, Glad it helped 🙏 thanks for the visit. Please share, thanks.🙏 Thanks for the like and thanks for watching.🙏

[@kane930]

Great video, fast, to the point, like an executive summary.

[@EasySteps_Sidhu]

I appreciate that! Thanks for the visit. Glad I could help! please share, thanks.🙏 Thanks for the like and thanks for watching.🙏

[@jeffreyertelt]

Excellent Video, short and to the point. Air bags are easy!

[@EasySteps_Sidhu]

Glad you liked it! 😊 glad to help. Thank you so much for the like and thanks for watching.🙏🙌

[@EasySteps_Sidhu]

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 kzbin.info

[@pashkoskoda3862]

Changed my 2014 gl450 rear air suspension over the weekend and I didn’t have to remove the height leveling sensor arm as the old and new suspension came out and in over the brake rotor very easy. I also did not have to remove fitting off of the new suspension as this is not recommended by manufacturer and it makes the job very easy just to push the air line in. I think anyone wanting to save some money can do it. NOW MY QUESTION TO YOU. I ONLY CHANGED THE REAR LEFT THAT I HAD AN ISSUE WITH BECAUSE RAIN DICTATED WHEN I STOPPED, BUT DO I REALLY NEED TO CHANGE THE OTHER SIDE AS WELL? I DO HAVE A NEW AIR SUSPENSION THAT I PAID FOR, BUT NOW THAT EVERYTHING IS OK IT SEEMS THAT I DONT WANT TO FIX SOMETHING THAT IS NOT BROKEN.

[@EasySteps_Sidhu]

Glad to help, first of all, congrats, and thanks for sharing the info. Please don't change it as you said "TO FIX SOMETHING THAT IS NOT BROKEN" Thanks again for sharing the info. and thanks for watching.

[@EasySteps_Sidhu]

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 kzbin.info

[@alikelystory7151]

Super straigt-forward video. Thanks for taking the extra time to vid/post.

[@EasySteps_Sidhu]

So nice of you, You're welcome! 😊 glad to help. Thank you so much for the like and thanks for watching.🙏🙌

[@EasySteps_Sidhu]

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 kzbin.info

[@alikelystory7151]

One of the most well-done DIY vid's ever

[@EasySteps_Sidhu]

So nice of you. Glad it helped. Great to hear!👍👍. Thank you so much for the like and thanks for watching.🙏🙌

[@EasySteps_Sidhu]

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 kzbin.info

[@davidpedder9048]

Makes you wonder why the dealer wants to charge you $$$$$$$ for such a simple job. $100 ànd a few hours ( if that ) of you time. Thanks for the video !!!!!

[@EasySteps_Sidhu]

You are most welcome. Thanks, glad to help. Thank you so much for the like and thanks for watching.🙏🙌

[@davidjacobs8558]

You can remove and install the real air suspension bag through the space between the control arm and the wheel well, if the wheel is off. no reason to uninstall and re-install the height sensor. there is enough room to manuever the air bag, if you just squeeze it down little bit.

[@EasySteps_Sidhu]

Good point, thanks for sharing the info.

[@davidjacobs8558]

@@EasySteps_Sidhu also, Bilstein is the OEM company that manufactured these air suspensions for Mercedes. However, there are German made ones, and USA made ones. German made air suspensions last around 10 years, but USA made Bilsteins only last 5 years, in my experience. so get the German made Bilsteins, if you can find them.

[@fuffoon]

I cheated. I called my local general service station and asked if they would install Arnott bags and they did it. The Arnott bags are working like new at the same age as when I replaced the OEMs. General shop advantage. I can choose the brand.

[@EasySteps_Sidhu]

Glad it helped! 🙏 thanks for the visit. Please share, thanks.🙏 Thanks for the like and thanks for watching.🙏

[@pineda.C]

Thanks for the video i have problem with rear air bag suspension. Im goin to change but just i wandering what's the normal level.

[@Ihsanhassan1]

You should have removed the new fitting out and you don’t need to for a lot of manufactures it voids the warranty by removing it

[@daverowlands2948]

You don't need to remove the ride height sensor or any other nuts or bolts that's the hard way

[@EasySteps_Sidhu]

Yeah...you don't need to remove them. 🙏 thanks for the visit. Thanks for watching.🙏

[@rsn3475]

Good video simple explanation clear voice, well-done.👌

[@willmill409]

Which brand bags did you buy and how long did they last? I see alot of cheap ones on amazon but im wondering if any of them last

[@stephenmichael3395]

Thank you soooo much for this easy explanation..

[@Tahseen4695]

So i ordered the pair of air springs that you listed in the link below. The new air springs look kinda different from the stock ones on the car, but wondering if it fits right anyways. Looks like it worked out for you in your video

[@EasySteps_Sidhu]

Yes, they will work fine. Good luck with your DIY project. Thank you so much for the like and thanks for watching.

[@EasySteps_Sidhu]

I am posting a thanks message to my viewers/subscribers for their support. Both KZbin channel was hacked/hijacked on (4/24/2019) and I got it back now (5/5/2019). The hacker has deleted the information under the description of my videos as well as all my comments. My KZbin Account Got Hacked - kzbin.info/www/bejne/Z6mvdpafha-kos0

[@EasySteps_Sidhu]

I have started posting auto videos on my other channel "Sidhu DIY" so please subscribes, thanks. Here is the link for my other channel, thanks. kzbin.info/door/uifMS69Pmx-ykxCar5XW6Q

[@RAJsWork]

Great video as always. Pls do a video on this same vehicle on how to upgrade or replace the glove box bulb to LED. Because some led bulbs tend to stay on despite the glove box closed for many minutes.

[@Neoncityinc]

Thank you for all your efforts to show other GREAT JOB .

[@onexsculler]

VERY IMPORTANT. Note the orientation of the jointed arms on the ride height sensors. If you reinstall them incorrectly your airbags will not fill.

[@EasySteps_Sidhu]

Thanks for sharing the nice info. as always sharing is caring. Thanks for watching it.

[@EasySteps_Sidhu]

I have started posting DIY videos on my other channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my other channel, thanks in advance.🙌 kzbin.info

[@mikegarcia4064]

How about the front air suspension. Is it the same?

[@minshikpark9761]

Awesome video! Thank you. Which point did you use for jack stands?

[@EasySteps_Sidhu]

Next to your wheels. Happy to help 😊😊 Cheers! Thank you so much for the like and thanks for watching.🙏🙌

[@EasySteps_Sidhu]

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please like, share and subscribe, thanks. Here is the link for my 2nd channel, thanks in advance.🙌 🙏 🙌 kzbin.info

[@21DannyC]

Hey man great video. I had a few questions I would like to ask you in regards to my 2012 CLS 550. I was told I need to replace the left and right rear air suspension strut. This part is said to be covered under my CPO extended warranty. However, I am being told that it isn’t covered bc it’s not a part not in fact covered. Am I being given the run around or could this be true? Not sure how many parts go in to the suspension. Thought it was the actual air bag and strut. Could use your expertise. Thanks.

[@pvcmvn5992]

Thanks for the video. I changed the back passenger and It worked fine, the bags inflated with no problem. Car was leveled perfectly. As Soon as I changed the back driver side, same steps, the car lowered and would not rise again. Thought it maybe be the 40 fuse so replaced it but no luck. The compressor is fine since the front lefts? No leaks either? Any advice on what may be the issue? Is there a factory reset or something to get the back up they way they were before? Sorry for the long rant, but i need some insight from an expert. Online forums dont address the issue.

[@pvcmvn5992]

Easy Steps please clarify? The sensor on the chassis? I didn’t disconnect anything only unscrewed it from the frame! So it seems that the first set of bags I bought may have been smaller, I installed a bigger bag 14” and it looked fine when the car was jacked, once drop it stayed elevated but dropped once I drove it. Alot of bouncing from the rear. Ince parked the bags inflated but I don’t think its to the full potential as when i took them off the jack?

[@IRTermite]

Peter Canizalez theoretically, it doesn't really matter the length of the bag, as long as it has similar range of motion. The car has no idea how big the bag is; just that the ride height sensor is telling it to rise or lower (ie: add or remove air). If the car is not leveling properly, perhaps you forgot to re-attach the sensor arm, or broke it? Doubtful there are other holes to bolt it to, but did you put it back in the wrong position maybe? Maybe the sensor arm is dead all-together and that was always your issue? Check the wires to the sensor, that you didn't accidentally disconnect or damage the terminals. Good luck.

[@dahian5194]

Peter Canizalez same thing happened to me, go back and make sure you put the level sensor back the way it was, the arm has to be facing out... thats all

[@andrewb8961]

Hey man. Great video. What would happen if you do not remove the fuse before?

[@EasySteps_Sidhu]

Potentially it can cause other issues, a good idea to be on the safe side. Thanks for watching, glad to help.

[@EasySteps_Sidhu]

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my 2nd channel, thanks in advance.🙌 🙏 🙌 kzbin.info

[@setidepp4853]

Mercedes Benz owners beware!! The people from Strutmasters have a rip off with the so called "conversion kit", no matter what car it is. They advertise this conversion kit will solve the issue of the "expensive" Airmatic ride in Mercedes Benz. On the contrary, their product is a very low quality, highly expensive replacement part since it does not last more than a year and a half. When you contact them, they say it is not their fault, that they only buy parts from other vendors and put them together and they supposedly do not have any control on the durability of parts. The kit is $1,300 initially and they don't sell just the front or back sets, you have to buy the whole thing. Later on, when it fails, they urge you to buy the whole thing again. And the "discounted price" they tell you they will give you if anything happens in the future is not true. They charge $586 for each seat, front or rear, which is basically the initial price. I urge all owners of Mercedes Benz to buy the replacement Airmatic struts and save the headache of having a below average conversion with a kit that does nothing of what is advertised and really turns your car in a piece of junk that is almost impossible to go back to the Airmatic. The movements of the car change badly and then when the Strutmasters shocks begin to fail they make a horrible squeaking noise that is almost unbearable. I wish I never bought the kit from them!! I only had to save a little and buy the real thing, the OEM struts that would last years and years before failing. On top of everything Strutmasters customer service is the worst and they even use women to hide behind lame excuses!

[@EasySteps_Sidhu]

Thanks for sharing info.

[@EasySteps_Sidhu]

I have started posting auto videos on my other channel "Sidhu DIY" so please subscribes, thanks. Here is the link for my other channel, thanks. kzbin.info/door/uifMS69Pmx-ykxCar5XW6Q

[@dope628]

Should post this on their website!

[@smelmybut]

Question...brother... Will these steps work on a (211?) 2006 e350 4matic wagon AWD with air suspension. The rear needs replacing ..also where would you suggest buying the part for? Thanks Brother. Malcolm in Tacoma, WA

[@PeterDammar]

Nice job. Should I hear a hissing sound from the rear driver side? Thanks

[@EasySteps_Sidhu]

Thanks, it's normal to hear the hissing sound for 2 to 3 seconds after turning off your car but if you hear it longer time then definitely you have a leak, thanks for watching.

[@EasySteps_Sidhu]

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my 2nd channel, thanks in advance.🙌 🙏 🙌 kzbin.info

[@bogdancuc9869]

thanck you from Spain you are the best

[@pashkoskoda3862]

Nice video. Thanks for sharing.

[@EasySteps_Sidhu]

Glad to hear that! You’re welcome 😊 glad to help. Thank you so much for the like and thanks for watching.🙏🙌

[@EasySteps_Sidhu]

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please check it out and subscribe, thank you.🙌 🙏 🙌 kzbin.info

[@max22706]

another great video, thank you.

[@kaibintech]

great video!

[@EasySteps_Sidhu]

Thanks, glad to help. Thank you so much for the like and thanks for watching.

[@EasySteps_Sidhu]

I have started posting auto videos on my other channel "Sidhu DIY" so please subscribes, thanks. Here is the link for my other channel, thanks. kzbin.info/door/uifMS69Pmx-ykxCar5XW6Q

[@incubus_the_man]

Was there not a soft rubber flap on top? I know the A1663200325 and A2923200525 do have rubber flaps that go on top,

[@mikebenz86]

I just got the front air suspension fixed today the dealer charged me 2,100 it was low to the ground last week so I took my car to the dealer today gl550

[@RuvimAbaras]

thank you!

[@EasySteps_Sidhu]

Great to hear! Glad I could help! please share, thanks.🙏 Thanks for the like and thanks for watching.🙏

[@RuvimAbaras]

I changed my rear airbags and for some reason it doesn't want to inflate

[@deegreatest6460]

I also have a X164 2007 GL450 and noticed that you have LED DRL in the front. I'm looking for the same ones that you have and wanted to know how did you wire them to come on with the engine every time it starts. Thanks in advance. - Dee.

[@amex1997]

Great video thank you, when will you be doing the fronts?

[@maximusfuscus]

Did this GL have the ADS (adjustable suspension - sport comf mode)? If yes, would it matter what spring (not strut) would I install? Please reply asap as I am about to purchase. Thank you!

[@Easton21]

Awesome video! Where is the jack point though? I have a floor jack and can't figure out where to lift a w164.

[@IRTermite]

Greg Anderson frame points are rubber blocks in front of rear and behind front tires on the outter frame. There are also ribbed points on the lower control arm if want to support by the suspention.

[@jessed772]

Great job thank you for sharing !!!

[@EasySteps_Sidhu]

Thanks. You are most welcome, glad to help. Thank you so much for the like and thanks for watching.

[@EasySteps_Sidhu]

I have started posting DIY videos on my other channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my other channel, thanks in advance. kzbin.info

[@franklynordz4030]

Wow that was so easy.. Nice thank you

[@henrylong45]

Another excellent video!

[@jessevang4082]

I have a question have you done the front mounts?

[@user-iy1dw7rp3v]

Hi Is this method suitable for x166 chassis 2013-2016?

[@garrettsl30]

Great video.......Could you please post a video for the GL Class X166 air suspension replacement or provide directions. Many thanks and Bless you man.

[@alexs.6109]

It's the same for X166.

[@kaibintech]

Great video!

[@EasySteps_Sidhu]

Glad you enjoyed it, 😊😊Thank you! Cheers! Thank you so much for the like and thanks for watching.🙏🙌

[@EasySteps_Sidhu]

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please like, share and subscribe, thanks. Here is the link for my 2nd channel, thanks in advance.🙌 🙏 🙌 kzbin.info

[@PopoySD]

When you jacked it up using the floor jack, did you jack it at the rear differential? I can't tell because it's a little blurry on the vid...and then place the jackstands on the jack points on each wheel? I've been trying to figure out how to jack the GL from the rear...i know where the jack points are behind the rear wheels, but I need to figure out where to place the floor jack when lifting it in order to put jackstands in.

[@EasySteps_Sidhu]

I have posted another video of my GL550, please check it out maybe you don't have to change your bags. Here is the link: How To Replace Mercedes Rear Air Suspension Bags on GL Class X164 Chassis - kzbin.info/www/bejne/bJe0gpStaLGNq8k

[@EasySteps_Sidhu]

I am posting a thanks message to my viewers/subscribers for their support. Both KZbin channel was hacked/hijacked on (4/24/2019) and I got it back now (5/5/2019). The hacker has deleted the information under the description of my videos as well as all my comments. My KZbin Account Got Hacked - kzbin.info/www/bejne/Z6mvdpafha-kos0

[@EasySteps_Sidhu]

I have started posting auto videos on my other channel "Sidhu DIY" so please subscribes, thanks. Here is the link for my other channel, thanks. kzbin.info/door/uifMS69Pmx-ykxCar5XW6Q

[@NixRiq]

I changed all bags but the front won't lift any ideas?

[@Spacecraft_Repair]

Thank you!!!

[@Jsmash_424]

Can I do the same on a 2000 S500 Benz? Nice video btw

[@aleksandrpodriadcikov35]

No you can't.

[@kaibinrubber]

❤❤

[@EasySteps_Sidhu]

Thanks. Glad to help. Thanks for the like and thanks for watching.🙏

[@yeedust]

Thanks so much for this video, you saved my car. I have a question: after replacing both back air suspensions they are working great however sometimes it says malfunction! Any idea? Thank you again.

[@wanderlustluggageleather3977]

@@EasySteps_Sidhu thanks for the reply, i checked and there are no leakage, it works fine but sometimes malfunction shows and if i press rise both back suspensions deflates and the back of the car lowers down!

[@ccars008]

Only your meant to put the air back Into the sock before lowering back down as apparently his can damage the bag.

[@EasySteps_Sidhu]

You always let it filled up before you lowering down, once down then it will raise it itself. Here is the video I have shown in the details. - kzbin.info/www/bejne/lZCbpmZ9iLZnrs0 Thanks for watching it.

[@EasySteps_Sidhu]

I have started posting DIY videos on my other channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my other channel, thanks in advance.🙌 🙏 🙌 kzbin.info

[@49mus]

Perfekt Job 💪👍

[@EasySteps_Sidhu]

Glad it helped 🙏 thanks for the visit. Please share, thanks.🙏 Thanks for the like and thanks for watching.🙏

[@greynand]

Do u have a video for the front suspension

[@EasySteps_Sidhu]

Thanks for asking, I have posted a video for - Replace Front Air Suspension Shock on Mercedes | Arnott Struts for CLS-Class W219 | E-Class W211 - kzbin.info/www/bejne/lZCbpmZ9iLZnrs0

[@EasySteps_Sidhu]

I have started posting DIY videos on my other channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my other channel, thanks in advance.🙌 🙏 🙌 kzbin.info

[@PewPewDave]

The rears are stupid easy. Too bad my front is leaking.

[@victoravina409]

not all heroes wear capes

[@EasySteps_Sidhu]

Thanks, glad to help. Thank you so much for the like and thanks for watching.🙌 🙏

[@EasySteps_Sidhu]

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my 2nd channel, thanks in advance.🙌 🙏 🙌 kzbin.info

[@leonteng8977]

What brand air spring is used? Arnott or dedc?

[@lashii23]

My E550 air suspension drop down when the temperature is -5C or lower.

[@psygnale]

Everyones does, even with brand new bags. The air inside the bladder cools and contracts. When its really cold for extended periods, the air will contract so much the bag will appear deflated. No loss of air, just less air volume. Mercedes even recognises this and has mentioned it in the manuals for over a decade. If it only does this in super cold weather, you're fine.

[@marsidxara7626]

What about the bags in the front?

[@DavidSilva-mr5jm]

Any ideas why my 40 amp fuse keeps popping?

[@EasySteps_Sidhu]

Most likely your air compressor going bad, thanks for watching.

[@EasySteps_Sidhu]

I have started posting DIY videos on my 2nd channel "Sidhu DIY" so please subscribe, thanks. Here is the link for my 2nd channel, thanks in advance.🙌 🙏 🙌 kzbin.info

[@nativecrafts]

How much should it cost if I get tech work on it?

[@be.671]

cool.. r u a mechanic too.

[@BossBtv321]

What year model?

[@EasySteps_Sidhu]

Year Model: 2007 Mercedes GL450 (This procedure will be same from 2007-2012) Thanks for watching it.

[@propanbutan4634]

I'm surprised how poorly its protected from the elements

[@georgegleek]

Good video but 10 em em and 8 em em is annoying me lol. Just say 10 mil or 8 mil 🤗

[@tongtongwang]

why mine Gl350 2012, after replacing , both rear is not inflate air. Any one has any idea?

[@simhopp]

maybe your air pump is broken.

[@eleddi597]

Did you remember to reinstalled the fuse

[@viewtube3310]

What size is the airline ?

[@viewtube3310]

What size are the air fittings

[@dgomolina5475]

is this why my car says "car too low" cuz of the air bags?

[@IRTermite]

Lorena Molina that is correct... sort of. "Car too low" is telling you something is not operating correctly with your air suspension and it is unsafe to drive; could be leaking bag, leaking hose, blown pump fuse, or dead pump. Your ride is probably super rough and bumpy right now. This will also affect your handling, braking, and acceleration. Do you ever hear hissing? Do you hear the pump running?

[@BradaBear61]

Thats how mechanical smurf does the job when he had some fresh mushrooms from chefcook smurf😁

[@AMGTOUGEX]

10 "m" m" key

[@peterstevenson5418]

And mercedes will charge you a fortune for this

[@torontoauction9015]

it is wrong! Do not remove NEW fiting!!! read the manual first

[@annelaaubry4558]

This video is absolutely WRONG!!! DO NOT REMOVE the air compressor fuse unless you have a way to get your vehicle out of limp home mode. Leave the fuse alone, otherwise it's fine.

[@ulflei]

That is a great video why someone should listen to you as you never had any automotive video out

[@labrat56]

Sloppy video key steps were left out. Thanks for nothing .

[@EasySteps_Sidhu]

What steps are missing?