How To Replace Rear Exterior Door Handle 07-13 GMC Yukon Denali

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@timg-y8k]

FYI - on some of our vehicles (mine is a 2012 Denali) the yellow clip holding the latch rod (just before the 5-minute mark in the video) is very different than what is in this video with a release tab in the back which you can't see without a mirror. This clip is a pain (there are other discussions about it and most end with folks just breaking it off and buying a new one). If you happen to have this yellowish clip you will spend hours trying to undo the tab in the back unsuccessfully (which I did) - the easier solution is to take out the three hex bolts holding the whole latch to the door and then, without disconnecting any wires or cables you can turn the whole assembly to see and release the clip. This was about 10 minutes vs a lot of swearing and still not releasing that little plastic clip. I was worried it wouldn't clip back together (single-use things that I have seen) but it did and I actually had to do it twice because I didn't get the bolt in exactly the right position the first time. I had done a front door on the same vehicle and this clip isn't on the front door - I was flying through this repair until I ran up against that clip. One last thing - you will need a very small flathead screwdriver to release the tab on that clip - like one for eyeglasses... yeah try doing that with a mirror taped to the inside of the door... Good luck!

[@lzhouse6543]

I pulled my handle off in cold weather. This is an excellent video and hopefully I can repair it myself.

[@ron045]

Great video... Thanks. We did this as a father/son project today on our 2008 Avalanche. It was a little different because our rear door is straight vice curved for the wheel well. I could not open the yellow door lock rod, but on the avalanche, it's a lot longer. So I left it attached and just disconnected the handle from the rod while the rod was still attached below. Our new part did not fit perfect at first. The spring arm was not bent a true 90 degrees and there was friction which prevented the door from opening. We bent the arm with some vice grips to 90 degrees and everything went fine from there. Your video saved us a ton of money. Thanks Again.

[@CMGDMovies]

Went very smoothly on my buddy’s 08 Yukon ! It was a bit of a challenge tho because the child lock was on and the handle was cleanly pulled off so I had to mess around with a coat hanger to find the door release. Thank you!

[@1AAuto]

+CMGD Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@BlàckÐèàth]

Really appreciate your videos it's one huge reason I give you my business. I would like to note if you have large hands don't bother with that rod clip inside the door. You can much more easily remove the handle off the rod up top by twisting it once unbolted. There was no way I was getting my hand inside to reach that clip.

[@map105]

great video. Exactly what I needed to replace my same door handle. Went flawlessly. Thanks for making this. it helped a lot.

[@Cmimss]

My Handle just Came in the mail today! Can't wait to start on this tomorrow! on my 07 Denali XL!

[@coolhandryan]

Great tutorial by Mike. I followed this video to replace my rear passenger handle on my 2011 Sliverado LT with a couple of slight adjustments. The power window control comes off as a somewhat larger unit than just the plate in this video, but just as easily. There are also 3 bolts instead of two from this video, the extra is also behind the door latch. I was able to do the job without removing the door handle cable from the door panel which made it easier to put the panel back on. I just let it hang there while I worked. Everything else was just the same as Mike's tutorial. 1 hour job taking my time. The part I got from their site (I'm not affiliated with them) works great and looks just like the original. Good stuff, Mike. Thank you!

[@1AAuto]

+Ryan Andrews Thank you for your order. If you would like to leave us a review on Google it would be greatly appreciated. Here is a link to our reviews section. Have a great day! goo.gl/i5JFNY

[@RevelatingDemarchist4172]

This video made it a 15 minute job. Thanks!

[@rickschwerdtfeger5312]

Awesome video. Exact steps all included for a straight forward door handle repair. Only issue I had was I needed to bend the arm that holds the latch rod. The aftermarket one was rubbing slightly on the mechanism and preventing full motion to unlatch the door. By the way, if anyone starts to panic when you test the door and it won't open: Don't panic:) Just pull on the metal cable you disconnected from the door panel (only the metal part, not the outer sleeve), and the door latch will open from the inside.

[@mikegarcia9147]

Great video... very informative and awesome step-by-step directions! Made this repair on my wife's Yukon go faster than I expected, and didn't take up much of my Saturday! Well done guys! 👍🏼

[@1AAuto]

Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs! Have a great day! 1aauto.com +Mike Garcia

[@TheNorthwestWind]

Just ordered my handle, seems like I can use this video to install with ease. Will reply to this when I succeed or fail

[@1AAuto]

+Puff Puff Bass Fishing Thank you for checking us out. We can't wait to hear back with how the replacement went! 1aauto.com

[@jana10mac]

Thank you! I watched this step by step and was able to do it all by myself!!!

[@MrInternational716]

Excellent video, cut my time in half. Did the front without a video a few years ago!

[@1AAuto]

+josephohenderson Thank you for your feedback!

[@jddpt3281]

You don’t even need to remove the clip! once you unbolt it, just slide it out and work it off of the latch rod. Then slide the new one on the same way.

[@adammaloney7360]

Perfectly made tutorial, very helpful and convenient. Thank you for the help!!

[@brianpberardgmail]

Thanks! You just walked another non mechanic thru a cash savings job! Success!

[@1AAuto]

+Brian Berard Congratulations on the successful repair. We're glad the video helped you out. 1aauto.com 866-403-3393

[@birdcitygaming6951]

Your videos are amazingly easy to follow step by step thank you!

[@therealmrsmall]

Thanks! Ordered handle from you and replaced on 2012 Denali 😉

[@robfunk6069]

great video, one of the best start to finish "how to's" ive seen in awhilethanks!!

[@1AAuto]

+Rob Funk We're glad the video helped you out. Thanks for watching. 1aauto.com 866-403-3393

[@themakerdad566]

Thanks to this video I was able to repair the door handle that came off.

[@g.o.c8a739]

Is it the same process on the left side

[@agoogleuser7095]

Excellent Video! This "Stay-At-Home Mom" was able to replace my broken Escalade handle with ease and precision- thanks to you! I feel like Super Woman. :-D

[@1AAuto]

Nice work. Congratulations on the successful repair. 1aauto.com 866-403-3393

[@dtmoore916]

Just finished mine. Very easy. Thank you!!!

[@PTerracina]

Great video! I followed your steps exactly and had no trouble replacing my door handle. Thank you!

[@1AAuto]

Nice work. We're glad the video helped you out. 1aauto.com 866-403-3393

[@jasonrassuchine1513]

Worked great for my 2008 Sierra denali. Only difference was the door latch rod connector was slightly different, no big deal. Thanks for the help.

[@1AAuto]

+Jason Rassuchine We're glad the video helped you out. Thanks for watching. 1aauto.com 866-403-3393

[@TXSuburbanHomestead]

Thanks for an EXCELLENT video! Quick question - my lock trim rattles in my 2013 Sierra. Think replacing them will solve that??

[@ThePSO51]

great video!! thanks just one thing you dident show how the yello clip unhinges from the rod only cliiping in back on, I figured it out but maybe for someone else

[@mrpep1976]

I’m struggling now

[@sheilagarza5751]

Thank you very much, u did a great job explaining everything & I followed step by step & got my door handle on now time for the drivers side!!! Thank you again!!!!

[@1AAuto]

+Sheila Garza Thanks for watching. 1aauto.com

[@gabrielgutierrez8187]

thanks for this video I have to replace both of my rear door handles on my 07 escalade! I appreciate ya!

[@1AAuto]

Thank you for watching! Glad to be of help. Let us know how the repair turns out. 1aauto.com 888-844-3393

[@gabrielgutierrez8187]

+1A Auto Parts also my rear driver side window doesn't roll up but it rolls down do you have a video on how to fix that or what part do I need to fix it?

[@MrBeattyandy]

Awesome video. Having some issues though. I finish the whole process, test the door several times locking and unlocking it and it works fine. After I drive and it auto locks I cannot get the door open inside or outside. What am I missing here?

[@dennonhart5721]

what size clips do i need for door panels , i’m trying to figure it all out before i remove anything

[@troycooley10]

OUTSTANDING VIDEO. Worked very well

[@1AAuto]

+Troy Cooley Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1AAuto.com

[@microlord8898]

You saved me a ton of time and $$$$$. Thanks for putting these videos together!!!

[@1AAuto]

+MicroLord Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them: www.1aauto.com/exterior-door-handle-rear-passenger-side/i/1adhe00539?KZbin&CTA+Comment&ZUTqqEzpZg

[@davewells1402]

Steve Ross. Recently a friend turned my child lock "on" when the outside handle was off. Is this what you experienced and how do you get the door open again?

[@cxaguirre]

thanks. used it to replace my rear door handle. worked as instructed.

[@1AAuto]

Thank you for watching! Glad to be of help. Please let us know how the repair turns out. 1aauto.com 888-844-3393

[@jenniferrios6258]

Question the rod on ours is loose is that normal ?

[@MalSEA]

Thank you so much for the part and the video. I'm not that mechanical, so feeling pretty good about myself replacing this part on my 2012 Escalade. ;-) I did it yesterday and followed the video to the T, even the testing part a the end. BUT! When my daughter tried to get out of the back seat this morning at the school bus, the door didn't unlock. She had to manually pull up the door latch. The automatic lock/unlock feature doesn't unlock that rear right door now. If I manually pull up the latch to unlock, it will open, and it will lock using the automatic locking button. Mmmn. Fixed-removed and replaced the locking latch button (don't know if that helped) and reset the programming features to unlock all doors when in "park". All works now. (BTW. the clip on the door lock rod was the opposite way round on my 2012 Escalade.)

[@madtrader117]

I bet you accidentally enabled the child proof locks

[@pedrodelasancha516]

Excellent Video, as always. One question, though. I just bought a 08 Denali but the right rear side door handle was missing, like completely missing. I do not see the little metal rod you unclipped, the one you mentioned to transfer to the new handle. Do you guys sell that rod or know where I can get one? Thanks for your help in advance.

[@1AAuto]

+Pedro De La Sancha Thanks for watching! That metal rod is part of the door assembly and is something you will likely have to supply from the dealer or a salvage yard! 1aauto.com

[@lsusouthpaw9952]

The instructions are great minus the fact that I forgot to remove one of the three bolts at the beginning but other than that everything worked out great.

[@patrickreilly7576]

Awesome video, very informative, had job done in under 30 minutes

[@1AAuto]

+Patrick Reilly Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com

[@sharpdressed1799]

Took the negative cable off the battery post before starting the work on the door handle on the 2013 Tahoe. After installing the new door handle & reconnecting the battery cable, none of the electric door locks would work. Have you experienced this problem? computer issue?

[@1AAuto]

+Sharp dressed You may want to check all of the electrical connections that you had to reconnect to make sure that they are all seated properly. If they are not, you may have an issue such as this. Hope this helps you out. 1aauto.com

[@kyhomegarage3430]

Awesome video made my job so much easier. Thank you

[@dannylorenze6188]

Thank you.. Took about 15 minutes...

[@samuelraymarney]

Super helpful. Thanks

[@AbsolutePayroll]

Very well done and appreciate your time and expertise

[@1AAuto]

And we appreciate you taking the time to watch. Hope it helped you out. 1aauto.com 866-403-3393

[@charliewilliams3978]

Good reference video! Thanks Sir 😎💪

[@irvdog6192]

awesome video man I got a 2008 escalade it is the same thing as the yukon denali thanx alot very helpfull

[@lindsayraele2679]

I need help finding a latch rod to replace. When my door handle came off the latch rod must have come off. How can I find this part?

[@1AAuto]

+Lindsay Raele Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

[@bradthompson6445]

Great Video, made a complicated job simple !!!

[@1AAuto]

Thank you for watching. Glad to be of help. Please let us know how the repair comes out! 1aauto.com 888-844-3393

[@pablohernandez6863]

La puerta del lado derecho de atras fel pasagero como quitar el vober

[@katelynwiles3952]

Super helpful! Thank you!

[@1AAuto]

+Katelyn Wiles Thanks for checking us out! 1AAuto.com

[@GUNNER_78]

helped a ton! Thanks!

[@SandcastleAndy]

got to the spot at 5.01 where you just unclip the actuator rod..yeah right - mine is solid will not unclip anyhoo - and appears to be different design to the one shown - mine is a 2013 Denali diesel 2500HD passenger side rear door and ideas before I get the welding torch out - my clip has a small slot in the middle and is flat sort of off white color - not yellow as shown - any idea A1 Auto? or anyone else - and also handle isn't broken - it would appear to have just fallen apart? 2 pieces? any ideas? - your chat line btw the way told me to go watch a video - I WAS WATCHING THIS ONE - YOURS! lol

[@mikevickrey3902]

Best video I;ve seen

[@20BMR]

As a Minnesota guy who lives in sub zero weather here in the winter I replaced two on my 07 Denali and now two on my 08 Eacalade Ext, still can’t believe the price new or used that GM can’t put heavier duty handles on them.. All my friends have had to do the same with these type of handles they are very brittle and cheap 😖.. Think I’m going to buy a Jeep n keep the doors off, I have warm snow gear to stay warm.. Great video though and I keep my 10 millimeter close..

[@1AAuto]

+20BMR Thanks for checking us out. 1aauto.com

[@aaronbrown2186]

Right around 6 minutes you talk about the latch rod. Is the latch rod threaded? I actually need one, do y’all sell them?

[@1AAuto]

+Aaron Brown Thank you for your comment! The latch rod is not threaded, and we do not carry them unfortunately.

[@aaronbrown2186]

1A Auto Parts how does it push it down if it just snaps around it?

[@ghulamemustafa7159]

Thanks brother. A lot of love.

[@cforse1]

Thanks great video

[@1AAuto]

Thanks for checking us out. 1aauto.com +Image Bearer

[@stevistrick363]

What happens if a kid shuts the door and the handle does not work to open?

[@johncrubaugh4428]

any other tricks to getting the door lock rod clips off..i cant seem to get mine open :( 2012 suburban ltz

[@1AAuto]

+John Crubaugh Thank you for checking us out. The only trick is that with a thin flat headed object and prying it out and up to release. 1aauto.com

[@johncrubaugh4428]

i finally got it..mine was backwards i would say compared to the one in your video so once i tried the opposite direction it came off fairly quick..but my fingertips paid the price.. haha..thanks for the great video!

[@MalSEA]

Mine was opposite too. I was at it with pliers for a while before I figured it out. :-)

[@littscarking8897]

How do I git the door open The rear door

[@1AAuto]

+Littscar King Thanks for watching our video. We just need to know more about your question. Is the door currently locked? Do you mean opening up the door panel? We look forward to hearing from you!

[@sross1111]

Make sure your child safety locks are "off" before the installation or you might run into issues like I did getting the inside door to open.

[@1AAuto]

+Steven Ross Thank you for the added tip!

[@boat2020com]

Great

[@1AAuto]

+Ibrahim Khalifi Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/exterior-door-handle-rear-passenger-side/i/1adhe00539?KZbin&CTA+Comment&ZUTqqEzpZg

[@gigiwoe]

cool ☺☺☺

[@gigiwoe]

cool ☺☺☺