Thank you very much, this video saved the cost of a road service call and a day of waiting for service
@screamingeagle9553 Жыл бұрын
As others thank you! I thought I was going to have to install a new system and nope your video popped up and saved the day.
@truckingandfixing Жыл бұрын
You are welcome! Glad it helps!
@Dusgf842 жыл бұрын
Thank you. This video helped me do it myself at home and save some money. I'd like to add, the snap ring pliers I used were 9" with a .09 size tip. The 30 dollar 12" .125 tip were too big.
@8mpgmafia1094 ай бұрын
Dammm after 3 hours I still couldn’t get that ring off sir :/
@truckingandfixing4 жыл бұрын
Welcome to our channel! In today's video, Ryan will show you how to change out or replace purge value on Semi Trucks step by step. Ryan's truck is 2013 Kenworth T660. The video quality is not great, because Ryan was using just one hand to do the job while the other hand was holding the camera. Please give him some support by subscribing to our channel for more good videos. Make sure to "like" the video, so more and more people can discover our channel. Leave us a comment or question below, because we review every comment and personally reply to each one.
@pancholopez74572 жыл бұрын
Thanks to people like you is that I can work on my own truck!! 🙏 thank you!
@RC-Heli835 Жыл бұрын
Those snap rings are some kind of tough!
@alfredosaldana98146 ай бұрын
Thanks !!! Ryan you help me to save some money 👍🏻👍🏻👍🏻
@alek41592 жыл бұрын
Thanks man!!! This helped a lot. Especially when I had the same sound you have. Hopefully when I attempt this I don’t mess up. Thank you again!!
@georgiapatriot45753 жыл бұрын
Thanks Ryan. I just replaced the purge valve on my 2017 T680 following your instructions. Hardest part was getting the clip back in. The nylon o-ring on mine was split so I'm guessing that was causing the leak.
@truckingandfixing3 жыл бұрын
I am glad it worked well for you! Good luck!
@ammysanghera7474 Жыл бұрын
Thanks ...saved me time and labour
@yafeifox88654 жыл бұрын
wonderful video for someone who is looking to replace truck purge valves.
@yusufmahdi8921 Жыл бұрын
Thank you sir this really helps
@reitsforlife2 жыл бұрын
Thanks for help! I replaced mine today. Had a bit of trouble getting the damn snap ring back in but other than that pretty easy.
@durmusalisaritas6343 Жыл бұрын
Good job man thank you I will do olso I have same problem
@johnnydubrow22793 жыл бұрын
Your videos are great. Thanks for sharing your knowledge. Just subscribed and I'm working my through them. Even as a company driver I enjoy learning some of the mechanics behind it all. Much appreciated
@ANDREASRIAL Жыл бұрын
Exactly what's going to happen... pliers need to be able to this heavy duty snap ring.
@lyndleshelby62912 жыл бұрын
Hello Ryan, great video! I really enjoy your content. Couple of questions: I wonder if you would consider doing an air brake repair series of videos for every component from "nose to tail" on the truck? Would be interesting to have this content in one location with your professional explanations! Secondly, I'm looking for overhaul kit for Cummins CM570. Your recommendations? OEM? Rank order aftermarket?
@georgegonzalez88183 жыл бұрын
Great job.
@yusufmahdi8921 Жыл бұрын
Thank you sir this really helped me to change it
@motorax113 жыл бұрын
Thanks Ryan. Great video. Be safe out on the road.
@truckingandfixing3 жыл бұрын
Thank you!
@motorax113 жыл бұрын
If anyone else reads this. After watching this video I replaced one on my bosses 2005 Peterbilt. The main thing is having a heavy duty set of snap rings pliers to compress the ring. Perfect video for this job.Normally my boss doesn't let me fix stuff. Not because I can't. Just because he is a worrisome guy. Saved him a few days of a truck at a truck shop and a couple of hundred dollars. Enjoy.
@March8084 жыл бұрын
Perfect video🤙🏼 can you tell me what symptoms the air dryer was giving you? Mine keeps throwing air out the purge valve, someone said it could be the whole air dryer system which I doubt. What say you?
@michaeldelaney9952 жыл бұрын
Great Video, this had definitely saved me time and money!
@truckingandfixing2 жыл бұрын
Glad to hear! 👍
@jameswalker883210 ай бұрын
Excellent video
@classictruckpete78092 жыл бұрын
Very helpful. Thank you very much
@truckingandfixing2 жыл бұрын
You are welcome
@adamoyerbides70862 жыл бұрын
Thanks
@samuelc.71533 ай бұрын
Make sure all the air comes out!! Drain all the tanks and keep hitting the breaks until the air gauges are at 0 and you do not hear air when pressing break.
@2828Meli2 жыл бұрын
I have the same problem....air passing thru the purge valve...put a new one on and it's doing the same thing....any ideas
@haiderk3246 Жыл бұрын
Thanks 🙏
@UpDownLeftRight55Ай бұрын
Hey Ryan, I’m losing air on both tanks at the same time. 2018 Kenworth t680 Paccar mx13 epa17. What were your symptoms with this issue?
@cesarvelasquez94362 жыл бұрын
Thank you for the video, very much appreciated. Just wondering on the last part why when you go to install the new valve do you have to rush the installation? Just wondering what to look for.
@slavyanskiyrusich33684 жыл бұрын
Clean 👍
@kinggrinch55823 жыл бұрын
Thx for the video....my snap ring won’t snap back in though😫😫tried everything
@jerrystanton63482 ай бұрын
2 hour job for me. But 1 hour 58 minutes of it was just getting the old snap ring off lol.
@tshaunscales80862 ай бұрын
How do you onow your purge valve is bad
@samuelc.71533 ай бұрын
Safety eye wear!! Protect your eyes!!
@tanako98 Жыл бұрын
Looks easy. Ensure you don’t roll the seals. You willl get stuck in the middle of the road!! Do not purchase a aftermarket either.
@draconis0469 Жыл бұрын
This is truth bought one from Autozone that they no longer carry and 5 months late the upper seals have stretched and failed! Now sitting waiting to find a part!
@oralsherwood63992 ай бұрын
So how do you know this was a bad valve ??
@ryanclarke411411 ай бұрын
Any way I can get an opinion about an air issue? Leaking at foot valve only when hooked to a trailer.
@isaiahnelson63872 жыл бұрын
Good video, my 2015 t680 will take approx. 10 to 20 miles to adjust for the difference in weight concerning trailer height between drive tires and trailer,found no major leaks , leveling valve is adjusted correctly, what is with this delay in adjusting to a heavy load. verses a light load
@cdub55186 ай бұрын
I can't get the purge valve to go back in all the way and the old one won't go back in either. Any tips on what it could be?
@merizeru30654 жыл бұрын
Greatttt job
@keurylara59487 ай бұрын
I have a truck that wont build pressure after 70 psi can it be a bad purge valve?
@ricarcogarcia39832 жыл бұрын
awesome
@slavyanskiyrusich33683 жыл бұрын
If u can’t pull it out ! Mine was very old and frozen in , so I drilled a hole, put a screw in, use a hammer nail side to pull it
@truckingandfixing3 жыл бұрын
Thanks!
@alexandergarneriii26562 жыл бұрын
How long does it take for air pressure to build back up after valve is changed
@jjgr661 Жыл бұрын
Hey Bud do you remember who’s the bendix part number for that purge valve replacement?
@followeroftheway74 жыл бұрын
Just a little fyi I was told today they are waving the hazmat for now at landstar so I can go ahead and put my app in.
@truckingandfixing4 жыл бұрын
Thanks for the info. Best luck on everything!
@jayfloyd39184 жыл бұрын
Road-Field-Home with Ryan & Sophia Hey Ryan, just came across this video while looking to see if changing the purge valve was something I could do myself. Great video and very instructional! Going to grab one while running across80/84 to Oregon and try it. Thank you for taking the time to make this video. I’ve definitely subscribed. The bonus was finding out you’re at Landstar as well!
@chevellebelair14027 ай бұрын
Mine has a bolt not a snap ring
@prisr312 жыл бұрын
I replaced mine same one and the new one. Start leaking. Some air. Su is that happen. I did the same procedure. You just did. ??? Anybody know.
@marquisharris68103 жыл бұрын
My issue is i have to accelerate to build up my air pressure. When im driving my tanks go way pass 120psi. When i let off the gas, eventually my low indicator warning sounds off. I have recently changed the air dryer. I can hear and feel air coming from what it seems like the same area that you replaced though. It never purges either. Any idea?
@plucky21153 жыл бұрын
I'd say soapy water
@smud4u3 жыл бұрын
What was the original complain on these that you had ti replace the valve .??
@truckingandfixing3 жыл бұрын
It was blowing off, and the truck would not holding any air pressure.
@4309ne202 жыл бұрын
Where did you get the fancy pliers
@ARNIE316 Жыл бұрын
Hey Ryan nice video! i replaced my purge value and air dryer filter on my Peterbilt 2015 today! i just needed help on snap ring coming off. I purchased a snap ring pliers at harbor tools 13 $ , they where okay ! where did you buy your pliers? you should put link for those.... Thx Arnie.
@SophiaFox4 жыл бұрын
support
@2828Meli2 жыл бұрын
I had the same problem with air blowing thru and put a new one on and it's doing the same thing.......any suggestions
@Huertign0002 жыл бұрын
What's the pasrt #?
@warrenhardie1632 жыл бұрын
What type of kenworth is this?
@truckingandfixing2 жыл бұрын
2013 Kenworth T660 Cummins ISX15
@nunyabuziness8421 Жыл бұрын
Air compressor is weak taking that long to build up pressure
@garycarroll94473 жыл бұрын
Y’all should use go pros to do video plus you got two hands and should be able to edit
@nunyabuziness8421 Жыл бұрын
This isn't step by step you don't show you taking the valve out