How to Replace Spark Plug 2006-2013 Chevrolet Impala

Buy Now!
New Spark Plug Set from 1AAuto.com 1aau.to/ia/ACEE...
This video shows you how to install new spark plugs on your 2006-2013 Chevrolet Impala. Spark is one of the four required components for an internal combustion engine to run. If your spark plugs are failing, worn, or dirty, you may experience rough starts, rough idle, poor performance, or poor mileage.
This process should be similar on the following vehicles:
2006 Chevrolet Impala
2007 Chevrolet Impala
2008 Chevrolet Impala
2009 Chevrolet Impala
2010 Chevrolet Impala
2011 Chevrolet Impala
2012 Chevrolet Impala
2013 Chevrolet Impala
Tools you will need:
• 10mm Socket 1aau.to/oa/1AXA...
• Bent Nose Pliers
• 5/8 Inch Spark Plug Socket
• Ratchet 1aau.to/oa/1AXA...
• Marker / Writing Utensil
• Pick 1aau.to/oa/1AXA...
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@tiahodo11]

Great camera angles. Also, really appreciate the Impala videos!

[@evandergonzalez3668]

Tired of getting charged 200+ to do this work, I will give this a try this weekend. Let's see how it goes, thank you!

[@TRQ]

+Evander Gonzalez Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ

[@barrysauce]

Make sure you plug the vacuum hose back in!!! Or else the engine runs real bad! And you think something else is wrong! Did mine today happy new year

[@TRQ]

+@barrysauce Thanks for the feedback and happy new year! 1aau.to/m/Shop-TRQ

[@TheRealCoozi]

For those of you out there with a 3.9 06, instead of take the coil pack off alone take the bracket that it sits on.

[@GraylonRoss-jg3tn]

You never connect the negative battery cable first. It comes off first and goes on last due to a spark that can ruin your day with a battery blowing up in your face.

[@JuanRodriguez-yh8wl]

Do u need to disconnect the battery?

[@broduscrowell537]

I'll never buy an Impala again R.I.P.

[@Freemasonshair]

You should've put a ratchet strap on the front of the motor and unlocked the front motor mounts to swing the motor a bit forward, would make it alot easier bud.

[@basshead9872]

Shit I did this without even removing the distributor

[@bangarang74]

Why not just plugs and wires? Why coil too?

[@bobcrawford5083]

can`t you raise on lift to get better access to rear plugs?

[@jerrycannon6940]

Use ratchet straps to pull engine forward. Unbolt the motor mounts

[@frankg9281]

This is definitely not a 2012 Impala Engine

[@RYAN20246]

They charge fo much to do this simple job. Come on guys...lets go!

[@jerrycannon6940]

You didn't have to remove battery terminal man. Why didn't you pull engine forward with ratchet straps?

[@gravygrizz833]

Waste of time doing that, there's plenty of room back there to do it

[@jerrycannon6940]

@@gravygrizz833 would have took me less time than it took you. I'll change all 3 in the back less than 8 mins. You're making ppl do unnecessary work.

[@Maybe_XenOn]

@@jerrycannon6940 he's talking about the replacement of sparks plugs, not the battery. Also you say 8min to replace them but you'll have to add minutes for the rachet strap setup and removing front mounts to sway it towards you.

[@bobcrawford5083]

can`t you raise on lift to get better access to rear plugs?

[@budzmckenzie6606]

I was wondering the same. Could I just Jack it up to get a better view of the plugs?