This is how to replace a low beam headlamp on a 2006 Hyundai Sonata on the passenger side. There are two lamp housings on this car, one for low beam and one for high beam.
Пікірлер: 51
@gar20084 жыл бұрын
This video helped me a lot. Other videos are saying you have to take the whole headlight assembly off. Careful who you listen to. Thanks.
@jsinfo8064 жыл бұрын
Thank you!
@EliasDeJesus954 жыл бұрын
It’s all about preference. It’s easy to take off this assembly and plus you can see what you are doing instead of ‘feeling’ around. But it’s only an extra work of three bolts. But if you prefer to leave them on that’s fine too!
@brantleyalan88833 жыл бұрын
pro trick : you can watch movies on Flixzone. Me and my gf have been using it for watching lots of of movies recently.
@remyconner12603 жыл бұрын
@Brantley Alan Yea, have been watching on Flixzone for since november myself :)
@kalebivan98843 жыл бұрын
@Brantley Alan yup, have been using Flixzone for years myself =)
@TheRealOTK3 жыл бұрын
I thought you had to take the whole housing out, this is going to save me a lot of time, appreciate it!
@keithcunningham2254 Жыл бұрын
Please reference the side of the vehicle you are working on as the "passenger side." This convention has been long established. Shining a flashlight on (and zooming IN ON) the cap, the bulb connector, and the wire spring clip would have really been a helpful technique for this video. Thanks for making this video - I understand it, even without seeing it, based on your description since my motorcycle's three headlamp bulbs change the SAME WAY. Thanks.
@TheRealMikeWilly Жыл бұрын
Furthermore, if one is going to reference which side of the vehicle using left and right, do so as if you were sitting in the drivers seat, this practice is what is used by automobile manufacturers, and automotive repair literature.
@Willthethrill47810 ай бұрын
Great comments. Give kudos to the content creator for helping the community but could have been thought out a bit better. Just constructive criticism.
@Cyranowan Жыл бұрын
Thank you. Been a while since I have done this so good instructions
@undastan5 жыл бұрын
Audio description of the video worked for me. Gotta be sure the shorter end of the spring is completely out of the way or it will get stuff under the bulb plate instead of over it like it should be. Just saved me $80-100 bucks by not going to the dealership. They probably would have said the buld going out was caused by my crankshaft being out of line and needing lever fluid, which it cause the one light to go out...hahahahaahaaahaa. thanks!
@fmadhi Жыл бұрын
Appreciate that comment.
@ConstantGains2 жыл бұрын
Thanks bro!!! Big help
@ernestobadilloiii9171 Жыл бұрын
This was a huge help, thank you!
@jsinfo8065 жыл бұрын
Yes, that’s another project coming up. Thanks for the info
@liljons67534 жыл бұрын
It's a h 7 bulb....you didnt mention
@keithcunningham2254 Жыл бұрын
This headlamp bulb H7 changes the EXACT SAME WAY as the bulbs on my 2005 BMW K1200S & 2016 BMW K1300S motorcycles - believe it or not.
@wendelkanawyer43993 жыл бұрын
I'm replacing the driver side where I have to remove the battery but the video helps, especially with the little wire spring. I have a 2006 Hyundai sonata and I'm curious if anyone has had any transmission issues with the gear shifter and a clicking noise?
@hakimbouzina77223 жыл бұрын
Yup…
@justiceononiwu57092 жыл бұрын
Sure do
@BrotherPixle2 жыл бұрын
Nah sorry, i have an automatic
@Xcraigyy Жыл бұрын
yup.
@lynnboaz7528 Жыл бұрын
How Abt the passenger side?is it the first cap or the 2nd one by thr filter???
@gabrielinton1372 жыл бұрын
Thanks for this!
@moviejunkie1892 жыл бұрын
Appreciate it!
@alissaswofford4554 Жыл бұрын
Thank you!
@Kaleighca4 жыл бұрын
Super helpful!
@jsinfo8064 жыл бұрын
Thankyou !
@raybohn76 жыл бұрын
Notice the orientation of the bulb as it is removed to make installation of the new bulb easier?
@jsinfo8065 жыл бұрын
Is the bulb plug pushed all the way on
@DirtyPrancing5 жыл бұрын
Thanks for the video. If anyone can help, I've installed my new bulb and it won't light up. Is there anything I could've done wrong installing it? Maybe my bulb just doesn't work... :( Plz help
@jsinfo8065 жыл бұрын
Also you don’t want to touch the glass with your skin since skin oils can heat bulb up and make it burn out easily
@TheRealMikeWilly5 жыл бұрын
No the oils boil on the glass and cause it to shatter. The glass is filled with a mixture of an inert gas and a small amount of a halogen such as iodine or bromine. The combination of the halogen gas and the tungsten filament produces a halogen cycle chemical reaction which redeposits evaporated tungsten to the filament, increasing its life and maintaining the clarity of the envelope. But you probably have a blown fuse.
@liljons67534 жыл бұрын
Ever get it fixed...
@osafai.16544 жыл бұрын
Video should be titled "how to shove your hand into a car" bc that's all you see here
@max_vtv Жыл бұрын
What do u expect lmao
@BrotherPixle2 жыл бұрын
Is this a gls or gl
@keithcunningham2254 Жыл бұрын
Shouldn't matter at all.
@emilym5446 жыл бұрын
no the clip if pushed down will move out of the way
@girlsixdiva3 жыл бұрын
What about driver's side? Nobody wants to show us how to do that one -__-
@jsinfo8066 жыл бұрын
Yes
@clintonsomerville40206 жыл бұрын
So you don't have to loosen the two screws holding the clip
@frenchy11075 жыл бұрын
No
@TheRealMikeWilly5 жыл бұрын
Looool nooo.
@Chris-vv9ui Жыл бұрын
My clip won’t come out
@TheRealMikeWilly5 жыл бұрын
You're losing 50% of your down road and 40% of the brightness with those hazy lenses.
@keithcunningham2254 Жыл бұрын
To clarify the lenses, buff out with Mothers Aluminum Mag Wheel Polish, wash residue with soap & water, then rinse. Dry, then place 2 or 3 coats of UV protectorant in stages, letting each coat dry. Alternatively - replace the entire headlamp buckets with new units after you treat the new units with 2 or 3 coats of UV protectorant.
@rogerhensley21645 жыл бұрын
You could have just left the video off. Couldn't see anything. !!!!