How to Reprogram your New Throttle Body 02-06 Nissan Altima

Buy Now!
New Throttle Body Assembly from 1AAuto.com 1aau.to/ia/1ATBA00008
In this video, 1A Auto shows you how to reprogram your throttle body. This video is applicable to the 02, 03, 04, 05, 06 Nissan Altima
🔧 List of tools used:
• No Tools Needed
For More Info visit us at 1aau.to/h/be7/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@avfonsi438]

Thank you guys at a1 auto. This video helped me a lot. I didn’t know you had to reprogram anything until now. It worked great with my 2002 Nissan Altima with a manual transmission. But I also followed the advice of another person to make the idle go back to normal. When getting rid of the code then you have to unplug the throttle body and the battery- , wait a minute or so plug it all back then put the ignition on On wait 3 seconds, then pump the gas 5 times in 5 seconds then let go of the gas pedal Wait 7 seconds then hold it down for another 10. The check engine will blink then when it stops blinking and stays on let go of the pedal wait 3 seconds and turn the vehicle on. The cars idle should go back to normal. Like 600 - 800 rpms. Thanks again.

[@avfonsi438]

2.5 engine by the way

[@rickezenterprise4975]

Does that goes for nissan AD o 07

[@rickezenterprise4975]

It works on nissan AD 07 too

[@1adorableone]

Helpful solution to my situation 2005 ultima 2.5, after numerous tries of the car not taking the reset I did 2 things, first I reset the check engine light to get it off : switch ignition on 3 sec, 5 times press accelerator release in 5 sec, wait 7 sec, hold accelerator down 10 sec. Second I disconnected both the negative battery cable and the throttle body harness then reconnected. Afterwards completed all instructions in this video using stopwatch letting it run continuously through steps, being as on time in the seconds as possible and now mine is fixed! Thank you 1A Auto for your super helpful turorials, you are greatly appreciated!

[@1AAuto]

+1adorableone Thanks for your great reply! 1aauto.com

[@avfonsi438]

1adorableone holy moly thanks man. It worked what you said and did. Thank you so much. I was getting spooked lol

[@livingonedgeslots]

Thanks I just did the same thing on 2009 Honda Accord I cleaned the mass air sensor and throttle body it was Revved high did this in 5 mins it worked thanks 🙏🏾

[@marydensio]

For Nissan Tiida 2007: After CEL becomes solid again release the pedal, start the engine within 3secs and let it idle. If it's still high-rev/pulsating idle, with foot on the brake, shift into Drive. Idle will now go down under 1000rpm. Shift to Park again, and the car will find its regular idle speed (near 650-700 rpm). BTW, thanks for the video.

[@mecey1978]

thank you, took me couple times, dont know why but after third try idle went back to perfect.

[@korotaszep]

There's nothing wrong with my 2006 Sentra throttle body, I did exactly like the guy said in the video, in the order he said, and it worked. Idle came up about 2-300rpm, from 500. The service engine light didn't do everything he said, but the idle still came up. Good deal. Thanks.

[@dansmith3933]

I have a 2012 Nissan maxima sv So I keep getting a check engine and traction control light and my car slows down to a stop I cut it off and cut it back on a few mins later works fine but check engine light still on take it to nissan said its my throttle body fixed it fine next week does it again they say its the k&n cold air intake on it making the throttle body clog up but I just can't see how shop manger says its the oil in the filter is this possible?

[@johnnygxiii]

I had the worst luck and almost gave up and took it the shop. Make sure your codes are cleared. Drive around for a little, stop the car, take keys out ignition for a little. Keep your key in the ignition and do everything in a row and use a stop watch. On the 2nd step, turn on and off quickly instead of counting. Did it like 20 times and having a breathalyzer made it even more difficult 😅

[@hayderali9385]

Thank you for your video.. Is that mothed suitable for 2012 model nissan altima...??

[@rayrayg231]

I had a P0101 code for my Nissan Altima 2012 and I replace my mass airflow sensor, but the code didn’t go away. So I put the original mass airflow sensor back in and Performed the closed throttlebody relearn and so far for a week my check engine light has been off.. Thank you

[@don_juan9582]

Is it the same for a manual transmission 2002 Nissan altima 2.5

[@jackala67]

On the idle air....after pressing 5 times the engine light will not blink after 7 or so seconds...anyone had this problem?

[@belio6738]

Would it be the same procedures for a manual trans too?

[@TSA333]

Does Nissan Rogue 2014 awd sl also has electric body throttle which requires relearning after cleaning?

[@williamrogacki1710]

I hope you still look at this. Is it the same procedure for an 02 frontier manual trans?

[@mydungtran9858]

Thank you for video. I followed step by step your procedure and applied to my 1996 Nissan Quest, my car is running good. Once again thanks much.

[@1AAuto]

+Mydung Tran Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1AAuto.com

[@bgminton001]

What size engine do you have?

[@jacquelinelambie1874]

I was interrupted in the sequence while attempting to program idle air and the throttle will not accelerate the engine. Is it necessary or possible to reset or clear the throttle body to do the reprogram procedure again? I've tried starting from the beginning with no change.

[@rockhavengamefarm3190]

Should I do the same procedure on my 2005 Xterra 4.0l? I just removed the TB for cleaning then this happened, idle RPM is too high!

[@IllegalAnxietyWrestling]

I have a question? I have a 2006 G35 sedan and so far I changed the catalytic converters,A/T FR/B solenoid,Transmission Temperature sensor, fresh transmission fluid and filter, MAF , APPS, new battery, and new brake pads, plus fresh oil change and filter. My car symptoms are slip & vdc lights are on at the same time as the check engine light, late gear shifts, hesitant to accelerate from complete stop, RPMs are hesitant when pedal is fully depressed (very sluggish rev ups), reduced power, delayed response when stepping on gas pedal. Ive done the idle relearn procedure many times but its not sticking. Im lost , HELP!

[@javier31011]

I have a 2003 Nissan Altima, I programmed it and it worked, but once I start the car again it unprograms itself again. Any idea why?

[@leorael4497]

Will this work on 2006 lexus gs300 , . ? I just installed a new pedal throttle sensor & throttle body

[@alecsithong]

Thank you! I'm assuming it's the same for 2005 maxima since there is no video for it.

[@jrwagner6700]

How do u relearn the 2012 Jeep Patriots throttle body

[@bgminton001]

Do these procedures work with a 98 Nissan Frontier 2.4L? Because I’ve done these procedures probably 10 times with no luck

[@mckoylach1622]

Are all of these procedures applied to all Nissan models ?

[@JB-zy4me]

Hello I have same problem I’m trying to many time still is idle is high please help me

[@isaacboy808]

I have a 2017 Nissan Altima. Is this the same procedure I would have to perform on my 2017 Altima?

[@SaintIvo]

Do you have the learning procedure for a Nissan Altima 3.5 se 2007 ? Or a link to where I can find it

[@sunnyscof8639]

Please how can I correct bad idle on my Nissan maxima 2004 v6 while idle at 1800 on park mode with very high fuel consumption

[@efrenvillegas9088]

i tried this in my altima 2010 but it does not work because my TPMS & AIR BAG & STEERING WHEEL LOCK warning light. is there another solution in my altima? kindly help me because my rpm is 1500 for 2 days now after i spray trhrottle cleaner

[@thth5549]

hi. how to relearn throttle body for elantra hyundai 2013.

[@hatemsoliman4833]

Happy new year . How can I do Re-learn Nissan note 2007 1.6 automatic transmission . Thanks allot

[@oscarpmd1]

I, MY XTRAIL USED TBI HITACHI. I CAN NOT DO THE LEARNING DOU YOU HELP ME? I'M BRAZILIAN MECHANIC

[@mycuriositypodcast]

I can find how to do it on my 2015 pathfinder wih a push star button. Would it be the same?

[@immortalityreigns6352]

It did work perfectly for me 😊Nissan Liberty 2002

[@hexc0nn392]

Thanks for the video. I think it is working. car wouldn't start before. now it does

[@1AAuto]

+Conner CARANNA Glad we could help! 1aauto.com

[@mememetal666]

Will this work on a nissan 350z 2005?

[@thodwrisagoratsios6034]

This precession is ok for a Nissan Qashqai j10?can I do the same thing?

[@Chilango1990ful]

I have a 2008 nissan altima with push button it still the process to relearn the p2135 code

[@gusl9325]

Thanks...dhis video help me

[@justinbryant8487]

I need help with da 07 push button model plz

[@blairboyd1735]

I didn't know that you have to repogrammed the throttle body in a Nissan maxima,I tried to reprogram the Throttle body and the airflow sensor, but it doesn't work.The check engine light is on over 5 years now, and if you remove a certain fuse,it goes off.I got the car reved out but soon as the abs light and slip, the car loose it power.It will drive once it is in drive, but it is not revering out. Could you tell me what to do, waiting for your reply ok .

[@AlphaOmegaJesus]

Nissan N16 Sunny 2003 I have a problem with RPM - it's completely unstable The Throttle nail has been moved - and the idle sensor has also been moved How do I return the Throttle nail to the original factory position?

[@_papa._popa._71]

How do u get the Allen wrench to stsy inside

[@adriantejadaramirez3396]

I would love to find you guys have a version of this video for a Nissan Sentra 2015 B17 or similar. I will save a bunch of money now that I know better that you don't need a scan computer to perform all of these steps.

[@gabinetcompanyltd7251]

hello Sir, can you help me on How to Reprogram my New Throttle Body for 2006 Nissan Note, i will be glad thank you

[@crystrezerex2life]

What happens if the throttle plate doesn't move at all?

[@shanegriffin8339]

Can anyone comfirm that this works on a 370z. thanks

[@raihanuddin1118]

how to make nissan altima model 2008 ???2.25

[@nestorroman2694]

Great information sir! Do you know or where i can get information on how to do app travel sensor for 06 Mitsubishi Outlander reset and relearn procedure? I had code P2138 Any help will be greatly appreciated. Thanks.

[@salvadoraleman4674]

Will this work with a 2001 Pathfinder ?

[@jaimeramirez4766]

Is this applicable to old Nissan's? 87 Nissan D21

[@paulbryant8402]

I clean my Nissan qashqai 2010 throttle body and it just mest up high revin... What can I do.... Can anyone help.....

[@gabemesa3921]

Gosh, what a process. That's a bunch of steps. Can or should you do this if you have not replaced the throttle body?

[@livingthelife8443]

So you guys are legit was gonna order some parts but never heard of you guys

[@1AAuto]

Hello Derrick, of course! Feel free to reach out to us and speak to a customer service representative at 888-844-3393. We are happy to assist you with ordering or any questions you may have. +Derrick

[@dotagamer6519]

Hello sir in the dashboard appear engine service soon

[@andersonrosario9600]

My 2003 Nissan Pathfinder keeps the check engine light flashing

[@Tashab.8871]

i am having problems where i just installed the throttle body sensor and reset the battery but yet when i started the car up as the mechanic informed me to do my car is still idling loudly and as i put it in drive it shakes as if its going to cut off and thats how the old sensor did . on top of my car will not drive no higher in speed then 10 miles with my foot all the way down on the peddle .. please help what can i do if you may know i need help. thank u in advance :-(

[@therealbigfoot3076]

They need a dealership to reset it with. Consult 2 machine

[@stuckintime2714]

I got p0507!!! Quick question my 02 altima got a new engine runs bad from start should i do this??????? No vacuum leaks

[@1AAuto]

+stuck in time Since there could be multiple reasons why you’re experiencing this difficulty with your vehicle, I strongly recommend that you have a reputable mechanic inspect it. They’ll be able to troubleshoot the problem and tell you what part or parts you’ll need for the repair.

[@kayleeoconnor6051]

Im having the p0507 code come up will this step still work if I just replaced my throttle body

[@1AAuto]

+Kaylee Oconnor The P0507 code means the idle control system has excessively high RPM and would not necessarily be fixed by reprogramming the throttle body. We would suggest taking the vehicle to get properly diagnosed. Please let us know if you have any further questions, thank you.

[@PhillyDee215]

I use the scanner, great video😏

[@1AAuto]

+Philly Dee Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

[@grandizer4531]

You can't do this with a scanner?

[@mbarry9737]

Another important point to note: If the engine is idling too fast (like after the throttle body has been cleaned), then the ECU will NOT perform the programming. Therefore, Nissan says (NTB05-067) to unplug fuel injectors to lower idle speed. For example, on a 4 cyl, unplug #2 & #4 injectors. Do not rev up motor because it will set a code with the injectors unplugged, just immediately do the programming shown in this video and shut it off. Then plug the injectors back in and start the motor to confirm if programming was successful. Good luck, our $10,000 scan tool didn't even list an X Trail.

[@1AAuto]

+M Barry Thanks for the added tip! Have a great day! 1aauto.com

[@ricardoz.6701]

M Barry what if it goes to 2rpm and back to 1rpm reapeatly at idle?

[@fiogermi]

In which part of this process should you unplug injectors? Or when to unplug back? Thank you.

[@julioalvarez2757]

Great video, thank you! Is the reprograming different for the 3.5 V-6??

[@1AAuto]

+Julio Alvarez The computer should adapt to the new throttle body.

[@jairogutierrez7541]

1A Auto Parts when you say adapt do you mean automatically? Because I have a g35 with a new throttle body and gas pedal and I get nothing

[@srshwa]

I have a car problem. I have a 2006 automatic Nissan Altima 2.5S. There has been an emissions code, but not for misfire. The cars stutters and jerks sometimes when stopped while in drive or reverse. When I put the car in Neutral, the stuttering and jerking stops. This does not happen at any normal driving speeds, just at idle. What can be the issue?

[@1AAuto]

+@srshwa We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@007camera]

Thanx for posting 5his video! 🙏🏻🙏🏻

[@1AAuto]

+shir azi Thank you!

[@jesusmoya1575]

I have a 2006 nissa Altima 2.5l with a code p2101 to fix is to clean out the throttle body.. do I still need to reset or is that only when you install a new one

[@1AAuto]

+Jesus Moya Thanks for checking us out. While it may not be required to reset this while cleaning or swapping the assembly out, it may be in the best interest to do so, just incase. You can also speak to your local mechanic to see what they recommend. 1aauto.com

[@jesusmoya1575]

@@1AAuto thank you for getting back to me so fast.. I love your videos been following 1A Auto Parts for 3 plus years.. thanks again

[@alfredrevis1876]

Will this work on a 2008 Nissan altima 2.5? Thanks

[@1AAuto]

Yes, the how-to video you're looking for is here: +Alfred Revis

[@harshkhy]

Will it work for Chevrolet Captiva?

[@bellakaram8132]

In a Nissan Sentra 2004 I had to replaced 02 sensor ( the code P1279 show 1 bank 1 air fuel sensor was greater than the maximum allowabe limit) the RPM were find befor I replaced the 02 sensor. Now I can start up the engine just find when engine is cooled. But when the car engine warmes up the RPM drops and when I need to restart the engine the RPM will drop to 0. I get the same code P1279, I went and changed the PCV vale and still the will start the first time and when I truned it off and restrated the engine it has the power but the RPM drop to 0 I have to push the gas pedal 3 to 4 time to get the RPM up. Please help...

[@1AAuto]

+Bella Karam We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1AAuto.com

[@foosblood24]

I have an 02 Altima 5sp manual. We had just done the head gasket and the car started back up, however, the accelerator won't go up past 1500 RPM. Could my throttle body need to be reprogrammed?

[@1AAuto]

+foosblood24 Thanks for watching! If you disconnected the throttle body then you might have to reprogram it. 1aauto.com

[@SeanA88]

Do you have a video of cleaning the throttle body? I have a 2006 Altima 2.5 and there's no videos of cleaning it

[@1AAuto]

+Sean Anderson We do not have a video for this right now, but we'll keep this request in mind for a future video! 1AAuto.com

[@sypher0101]

3:48 you turns vehicle 'OFF', then turned back 'ON' and started the car. Was that part of procedure, or accident? I've read other Nissan relearning procedures but they don't mention turning vehicle off. Whenever I try to do the relearn, then start the car, there's hardly any accelerator. Car goes limp with very little accelerator. Not sure why :/

[@yungmaurice_9434]

Same bro same

[@RGZSoCal]

I recently replaced the throttle body on my 05 Nissan Altima 2.5 & a week later the car goes into Limp mode & I get the codes P1126 & P1122 what can I do to fix it ????

[@1AAuto]

+Richard Gonzalez Thanks for watching! Have you checked to make sure your throttle body is getting the correct amount of voltage? Those codes could indicate an issue with power delivery to the assembly. As always we recommend you have a trusted garage take a look at the vehicle to get a proper diagnosis if you are unable to do so yourself! 1aauto.com

[@DillysADV]

working on a 2006 xterra - performing the Idle air volume learning procedure.. after pressing and releasing the accelerator, the light does not blink.. it is solid the entire time.. I have checked my timing multiple times.. tried longer time and shorter time, all the same results. Any suggestions?

[@baseroom9]

DillysADV after pressing and releasing the pedal 5 times wait 7 seconds then step on it until it happens (no longer than 20 sec)

[@bigunit617]

Will this also work for a 03 sentra gxe1.8L?

[@1AAuto]

+bigunit617 We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

[@ExtremeKustomz615]

How do you turn the key on then on again ??? Did I miss something

[@johnnygxiii]

Turn the key on and turn the key on again.

[@makaylagarcia4720]

Will it work for Nissan Altima 2008 SE v6

[@1AAuto]

It may be similar. At this time, we do not have a video for your specific vehicle. +Makayla Garcia

[@jesusmoya1575]

Question I just clean the throttle body when I install it back. The rpms and going up and down 1500-2000 any suggestions

[@royguevara7128]

Why is doing the same thing

[@romeolopez607]

Jesus Moya did u fix it?

[@royguevara7128]

Yeah I took it off and cleaned it and put it back in

[@romeolopez607]

Roy Guevara took what off?

[@bendixsmith9642]

yes this method gonna work for all Nissan Altima to Relearn the throttle body try this method. ( Fully released the accelerator pedal and keep it for approx. (20 seconds unit the Engine light stops blinking and turn On not start the engine only turn On). (Fully release the accelerator pedal with 3 seconds after the Engine light OFF). (After Start the engine and let it idle for 5min the body throttle gonna Relearn). Thank you

[@gabriela1341]

Didn’t work on my 2004 nissan sentra 1.8 l

[@NightOwl2022]

Will these steps also work for the Nissan Versa?

[@1AAuto]

+NightOwl2022 This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-1AAuto-c

[@RGZSoCal]

What happens if you drive it without doing the relearning ?

[@KMGPRODUCTIONS]

@Pretty fly for a WiFi Let's say you get that p0101 code what would you do next? Replace the Mass Air Flow Sensor and then do the relearn procedure since I'm still getting a p0507 code?

[@photograffyc2139]

Hi, do you have a relearn for 2006 fx35 throttle body ?

[@1AAuto]

+Brooklyn 4 ever We're always cycling through common cars. We'll add this repair to our list! 1AAuto.com

[@photograffyc2139]

@@1AAuto Thank you..

[@RikterZilla]

I've tried this several times. The 2006 Murano has the Start/Stop button & this procedure does NOT work. I cleaned the throttle body & changed spark plugs. The code "Idle Speed Higher Than Expected" comes & goes. Other than that it runs fine but idles at 980/1040 rpm. Any thoughts? Thanks in Advance. BTW the 3 Liter V6 is a PiTA to change the back 3 plugs isn't it?

[@leibyperalta9600]

RikterZilla did you fix it I have the same problem

[@ReyHdez999]

How did you fix it? I have the same problem in my 07 Nissan frontier

[@ralfsautomotive]

Preparation Before performing Idle Air Volume Learning, make sure that all of the following conditions are satisfied. Learning will be cancelled if any of the following conditions are missed for even a moment. Battery voltage: More than 12.9V (At idle) Engine coolant temperature: 70 - 100 C (158 - 212 F) Park/neutral position (PNP) switch: ON (Shifter in Park or Neutral) Electric load switch: OFF (Air conditioner, headlamp, rear window defogger) Steering wheel: Neutral (Straight-ahead position) Vehicle speed: Stopped Transmission: Warmed-up (Drive vehicle for 10 minutes.) Procedure 1Perform "2003-2011 Nissan Murano Accelerator Pedal Released Position Learning" 2Perform "2003-2011 Nissan Murano Throttle Valve Closed Position Learning" 3Start engine and warm it up to normal operating temperature. 4Check that all items listed under the topic PREPARATION (previously mentioned) are in good order. 5Turn ignition switch OFF and wait at least 10 seconds. 6Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds. 7Repeat the following procedure quickly five times within 5 seconds. aFully depress the accelerator pedal. 8Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the MIL stops blinking and turned ON. 9Fully release the accelerator pedal within 3 seconds after the MIL turned ON. 10Start engine and let it idle. 11Wait 20 seconds. 12Rev up the engine two or three times and make sure that idle speed and ignition timing are within the specifications. Idle speed = 650 ± 50 rpm (in P or N position)

[@anthonyjenkins8722]

Will this work for a 2005 Pathfinder 4 liter V6? I am having the same trouble. Tried this to no avail... idles at 1500 rpm. Rev the engine it acts like it's going down hits 1100 then back up to 1500. When you drive it is stays 1100 rpm and will surge up to 1500 when your stopping or putting your foot on the brake.

[@1AAuto]

+Anthony Jenkins It may be a similar process.

[@patrickgann8856]

i have a 02 nissan sentra 2.5L and tried this a few times, when i would get to the light blinking it would never blink. so after a few tries i went on with the cranking an reving the motor and it seemed to work. an has been doing fine for about a week now.

[@Truckingfit1]

Me too

[@hindustanmerijaan1930]

Why it is not working on my car otherwise i have pay $80 to reset

[@stevenA44]

I cleaned my throttle body because the car was a pain to start even if it would and now the car won't stay running. I tried the first 2 steps but it keeps dying a few seconds after it starts. Any ideas? I've even disconnected the negative battery cable. Didn't help.

[@1AAuto]

+@MickDundee444 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@rlh9373]

My 07 pathfinder put in a ignition coil Bank 3 but before that I had to replace my alternator and when I replaced my alternator I saw a lot of black residue around my throttle I took a toothbrush and sprayed it with some throttle body cleaner car was idling funny for a while drove down the street it started rocking got back home turned the car off let it sit for like 6 minutes then drove Maybe 30 minutes it seemed like it idled out right then a couple of days later it started misfiring that's when I found out it was the ignition coil Bank 3 I replaced that then Monday the 9th taking my daughter to work dropped her off . Put gas in the then drove off car started acting like it was running out of gas and gas pedal got loose . Car speed was 10 mile or 5 miles an hour was able to park in the mall parking lot. I tried to reset by taken battery connection off for ten minutes. Reconnect then start the car it will run but shaking like it was getting no gas . Then I press the gas pedal it goes to the floor then suv shuts off . Tried a few times same results. Runs like a lawnmower running out of gas. Got the suv towed home got in and car will crank but no ignition and my gas pedal still really loose I got to hook it up to a machine to read the codes I think I have a friend that has one but I'm just wondering before I get it checked out is it my fuel pump that went bad or is it my gas pedal. Oh I also put a bottle of cataclean a few days before the car did what it did. I did that after I replace my ignition coil check engine light went out few days later the initial check engine light cut back on. Took it to O'Reilly's they hooked it up to the sensor it gave catalytic bank 2 codes so the next day I put in a bottle of cataclean . And after I replaced my alternator I put in a bottle of Lucas high mileage fuel treatment do you think the Lucas high mileage fuel treatment and the cataclean did something bad .

[@oscarvargas1543]

This works with Nissan Rogue 2018???

[@1AAuto]

+oscar vargas We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1aau.to/m/Shop-1AAuto-c

[@graphicscardtech3167]

How can I relearn on a 2009 Nissan Murano

[@1AAuto]

We currently do not have an auto repair video specific to your vehicle. You might be able to apply some of the basic steps shown in this video to your application. +R L

[@celestralshields7757]

What if car won't stay started?

[@yungmaurice_9434]

Can you do it for 2005 G35 coupe

[@1AAuto]

+Indoorboyz We're always cycling through common cars. We'll add this repair to our list! 1aau.to/m/Shop-1AAuto-c

[@wornven]

The light is off but I still get code p0507

[@coreydukes5725]

Yah not working at all for me at least stays solid

[@plymobil1]

How about if I have to start/stop button

[@1AAuto]

+playmobil We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

[@themountaindewer]

I did this process and it worked fine, but when I get on a hill it lags and has no power ?????

[@1AAuto]

+Darrell Partin Since there could be multiple reasons why you’re experiencing this difficulty with your vehicle, I strongly recommend that you have a reputable mechanic inspect it. They’ll be able to troubleshoot the problem and tell you what part or parts you’ll need for the repair.

[@JCno28]

Will this work on a 2012 Nissan Altima?

[@spectrakid92]

I need to know the answer to this as well! I tried doing it on my 2012 Altima but had no success. My rpm is currently idling at about 1000 rpm but normally it should be closer to 500. Please let me know if you find any answers, thank you!

[@bendixsmith9642]

​@@spectrakid92 Yes this method gonna work for all Nissan Altima to Relearn the throttle body try this method. ( Fully released the accelerator pedal and keep it for approx. (20 seconds unit the Engine light stops blinking and turn On not start the engine only turn On). (Fully release the accelerator pedal with 3 seconds after the Engine light OFF). (After Start the engine and let it idle for 5min the body throttle gonna Relearn). Thank you

[@mokomajoseph6113]

mk4 the same as this one???

[@1AAuto]

+Mokoma joseph We currently do not have this part listed as fitting that particular vehicle. Thank you for asking. 1aauto.com

[@paul1e]

Does dis work on qashqai j10?

[@1AAuto]

+PauL1e It does not. We currently do not have this install video for your vehicle. Thanks for checking us out!

[@paul1e]

@@1AAuto alright, thanks for the answer!