How to reset or clone the code of 4 Channel RF Key Remote Control 315/433MHz from ebay

[@Henscott]

Thanks for your help and advice.

[@gatchicagobullsph8210]

hello, i tried pressing A and B and press B 3 times while holding A but after that , i pressed any button it still light on, how do i fix this? it should not light up, right?

[@PAFixandCrafts]

@gatchicagobullsph8210. First of all, thank you very much for your comment!!! You should press buttons A and B simultaneously, then press button B 3 times, while button A is still pressed and hold it for another 10 seconds, then release button A. After this operation, the old codes should be deleted and when pressing any button, the light should not light up. To clone, put one remote control next to the other and hold down the buttons you want to copy, simultaneously on both remote controls. I hope my answer was helpful. And if you have other questions, don't hesitate to write to me.

[@francoisbarrat5800]

Bonjour , j'ai réparé cela en pressant simultanément A et B pendant 1 minute. Hello, I fixed this by pressing and holding simultaneously A and B for almost 1 minute.

[@gatchicagobullsph8210]

@@francoisbarrat5800 thanks so much it still light up even if i press the a for 1 minute :(

[@gatchicagobullsph8210]

@@PAFixandCrafts thank you, i bought 2 clone remote but both still light up :((

[@Xcitecity]

Just got my remote from Temu, and I have the same problem. I cannot reset it and delete the factory code. I tried all what you said. Anyone has the solution?

[@cotelo]

My car (kinda old) uses a TX-71 remote. I lost the original and bought the same on ebay, but when I try to pair it, it doesn't work... Do I need to clear the code in the remote? This remote has only two buttons, and the car should open/close with the same button.

[@gianantoniodellagnese9423]

Hi, I have a problem with the remote control, when I press the A and B buttons the led always stays fixed it never flashes. I have changed the battery but the problem remains. I cannot reset the remote control. Thank you if you can help me.

[@panhasambath993]

How do I do the copying if my old remote is completely broken and stop working?😢

[@PAFixandCrafts]

@panhasambath993. First of all, thank you very much for your comment!!! Unfortunately, these remote controls can only copy active frequencies. If they don't detect a signal, they won't be able to register a new code. However, it’s possible that your remote has an identification code that could help you order a replacement remote control. Alternatively, you might find 433 MHz remote control modules on AliExpress, which you can use to replace the entire module if needed. If you found my answer helpful, I’d really appreciate it if you could subscribe to the channel. Your support greatly motivates and encourages me to keep creating content!

[@Cotelic]

I do the steps but for some strange reason it doesent want to hold the frequency of the original controller

[@Justmevs]

Can you use this for a car key remote?

[@PAFixandCrafts]

@Justmevs. First of all, thank you very much for your comment!!! Unfortunately, this remote control isn't compatible with the car's system. To ensure compatibility, you'll need a remote control equipped with a dynamic signal, and in certain cases, a stabilizer chip might also be necessary for the car to start. Additionally, for older car models, compatible remote controls are often available on the market at reasonable prices. If you found this information helpful, I would greatly appreciate your subscription to the channel if you haven't already done so. Your support not only motivates me but also encourages me to continue creating and sharing new videos.

[@gianantoniodellagnese9423]

Ciao, ho un problema al telecomando, quando premo i tasti A e B il led rimane sempre fisso non lampeggia mai. Ho cambiato la batteria ma il problema rimane. Non riesco a resettare il telecomando. Grazie se mi puoi aiutare.

[@marypapava8268]

I pessed the top two buttons but the LED is not flashing :(

[@PAFixandCrafts]

@marypapava8268. First of all, thank you for your comment!!! Button A must be kept pressed and button B will be pressed 3 times consecutively while button A is still pressed. That should erase the codes on the remote. If you found my answer helpful, don't forget to subscribe to the channel if you haven't already. This helps me and motivates me enormously to continue!

[@gatchicagobullsph8210]

hope you can help me :( thanks in advance! i subscribed to your channel

[@PAFixandCrafts]

@gatchicagobullsph8210. Then I think something is wrong with the remote control. There is also a combination between buttons C and D that you have to press simultaneously for 20 seconds and it recovers the previous codes. I honestly don't know if it helps, but it's the last possible combination that I know of. Please try this and immediately try the first button combination again. If it doesn't work, write and try to document myself.