How to setup the MGC 4x4.

[@onserutiri488]

idk if this is a dumb question but how do you use the magnets and springs in the little bags that come with it? there was no manual of what to do with it.

[@leeleecuber]

Those are only replacements:)

[@ImManhHung]

ik this is late but how do i get the most corner cut since mine can’t get near to 45° but it still pops

[@leeleecuber]

Just mess with the tensions. I don’t think you’ll get 45 but probably close

[@andydoom6257]

Is the disassembly and cleaning necessary if I’m lubing it right out of the box?

[@leeleecuber]

If u want complete control then yes, but personally I would be too lazy to

[@pulsarcubes]

my stock one locks and doesn’t cut at all but also feels really unstable

[@leeleecuber]

Yea needs setup

[@AutZeroOneGotBanned]

mine is the same but slow

[@leeleecuber]

@@AutZeroOneGotBanned yep

[@AutZeroOneGotBanned]

@@leeleecuber I tried making it really loose but it was the same

[@leeleecuber]

@@AutZeroOneGotBanned yea that’s just 4x4 hardware.

[@jmech2298]

Hey bro i didnt fully understand. So did you lube every single edge piece eith weight 6?

[@leeleecuber]

No just the area I showed because it will spread :)

[@jmech2298]

@@leeleecuber okay sounds good bro. thank you my man for the fast response, im in the process rn following your video lol.

[@leeleecuber]

@@jmech2298 your welcome and good luck with the setup :)

[@thekaeden]

how do i get the best cornercutting possible cornercutting without it popping everytime i turn fast?

[@leeleecuber]

It should cut just below 45 and u should be good, so I think u need to tighten it :)

[@thekaeden]

@@leeleecuber alright thanks i hope it works

[@leeleecuber]

@@thekaeden :) me too

[@Thatoneguy78936]

ik I am late but I have a kinda annoying lock ups on the cube do you know how to fix it maybe I have to less rough on it or something?

[@leeleecuber]

This cube is locks when too lose or too tight. So your going to need to figure out which one it is, also make sure to lube it. Good luck my brother.

[@Thatoneguy78936]

@@leeleecuber tysm yes i think i just over losen it but it doesn't pop idk how also I have the jperm edition I am pretty sure it is lubed but after a week or 2 of using it I think it would be a good choice to lube it again

[@leeleecuber]

@@Thatoneguy78936 yea so maybe try that :)

[@aligameng5245]

I don't have lube is it a problem

[@leeleecuber]

Lol if u wanna do the setup then yea :)

[@gabrielbowman1267]

Hey leelee cuber do you want to have a 5x5 oh race?

[@leeleecuber]

yea im still working on posting the relay vid, and also i was thinking to do a 4x4 or 3x3 race because i dont do oh :)

[@gabrielbowman1267]

@@leeleecuber ok I can do that which event?

[@leeleecuber]

@@gabrielbowman1267 im sub 14 on 3x3 (trash) and sub 1 10 on 4x4 how about u?

[@gabrielbowman1267]

@@leeleecuber I'm between 10 to 20 on 3x3 and just under a minute average on 4x4 but we will just do 3x3 and go from there

[@leeleecuber]

@@gabrielbowman1267 ok les do it

[@Bulldogs_fan]

0:24. That is not how you’re supposed to solve a Rubik’s Cube. It’s cheating if you take it apart then rebuild it.

[@leeleecuber]

frick moment

[@leeleecuber]

@Justin Back i agree this is a lol moment

[@jeffayoe7468]

@@leeleecuber haha bruh momento. My guy thinks u cant solve a 4x4

[@leeleecuber]

@@jeffayoe7468 no he’s joking lol.

[@mathiaskruckow]

mgc 4x4 can cut 45*

[@leeleecuber]

it can if u want the cube to pop all the time lol

[@mathiaskruckow]

@@leeleecuber no it dos cot som times bot it dosnt rilly pop that much

[@leeleecuber]

@@mathiaskruckow yea

[@Good_Hamster5674]

when i loosened mine the screw head rubbed against the edge and damaged it. took me 2 hours to realize pls reply how do i make my cube looser without damaging edge pieces

[@leeleecuber]

I’m not sure what your problem is please specify:)

[@Good_Hamster5674]

@@leeleecuber so my cube was really tight (i tightened it after a bad pop and it took all day to find all of the little pieces) and i was trying to to get good at 4*4 so i had to loosen it. I tested the outer layer and it was super fast but when i tested the inner layer sth was making a scratching sound. I found out that the screwhead rubbed against the edge pieces and damaged them. How can I loosen the cube without damaging the edge pieces. Also i lost one of the small edge pieces. is my cube fine without them? thanks.

[@leeleecuber]

@@Good_Hamster5674 I can’t answer the first question as it hasn’t happened to me but as for losing some of the small edge pieces, it will pop a bit more but generally it should be fine :)

[@Good_Hamster5674]

@@leeleecuber thanks a lot :)

[@leeleecuber]

@@Good_Hamster5674 no problem:)

[@liamgumprecht4983]

super epic indeed :)

[@leeleecuber]

agree moment

[@leeleecuber]

pls like this vid dont have any likes :(

[@liamgumprecht4983]

@@leeleecuber well convince me through something else than pity

[@leeleecuber]

@@liamgumprecht4983 if u like ur a prankster gangster LOL

[@liamgumprecht4983]

@@leeleecuber wow even more epic than the vid

[@turtle2494]

My faviorate is zhilong mini 4 m

[@leeleecuber]

nice, i dont have it but i heard its really good :)

[@turtle2494]

Its is comeing tommorwo and i will make a unboxing

[@leeleecuber]

@@turtle2494 thats so cool :) i cant wait to watch ur unboxing

[@turtle2494]

Thnks

[@turtle2494]

But i dont know when will the video come i might be delayed