How to square the gantry on a Chinese Laser

  Рет қаралды 8,775

Laser Artifex

Laser Artifex

Күн бұрын

Пікірлер: 15
@NFOsec
@NFOsec Жыл бұрын
THANK YOU!... while sometimes I feel mechanically and electronically inclined to do these things on my own, this guidance is spot on. Cheers.
@terrybrockhoff8168
@terrybrockhoff8168 Жыл бұрын
Thank you , one of the best info videos i have seen on youtube for a while, I knew I had a problem but not sure why things were coming out not square.
@joedilaura2560
@joedilaura2560 7 ай бұрын
Thank you for your video. I have been dealing with my laser being out of square for a while now. Your video pointed me in the right direction and YES it worked. I solve the problem of getting a square to measure rail to rail by clamping a 1-2-3 block the Y rail. That gave me the height and a good reference to use my square to straighten it out.
@MrCtronic
@MrCtronic 10 ай бұрын
Thanks a lot for the good explanation and ideas on how to measure the bigger diagonals. Very good job!
@JMadoreTutorials
@JMadoreTutorials 3 жыл бұрын
Thanks SO MUCH for this tutorial. I searched high and low and could not find this information!!
@markrumrey790
@markrumrey790 Ай бұрын
THis can also help with cross bed beam alignment!
@SarbarMultimedia
@SarbarMultimedia Жыл бұрын
With most macvhines the Y belt tension is achieved by adjusting a unit on the backat each end of the gantry. If you tighten the ajustments differently this may be the real cause of the gantry being off square so be careful to adjust both belts by the same amount. The method demonstrated is exactly what you need to do, with the big sqaure and equal diagonals method. However there is one impoertant point missing from this video..... the gantry bearing blocks. Those bearing blocks are usually pre-tensioned onto the rail to ensure they are bscklash-free. If you twist the gantry then you are twisting the beaiing blpcks out of line with their free running position and this will result in premature bearing wear.. It is therefore important that your slightly loosed the end bearing blocks so that they can "float" into thier natural stress-free alignment. Dint forget to retighten them after you have squared the axes..
@jordanlavely6992
@jordanlavely6992 2 жыл бұрын
Greatly appreciated!
@runifuceeme406
@runifuceeme406 10 ай бұрын
@4:05 HEHE... HE SAID "GRAB THE SHAFT"...
@gustos2478
@gustos2478 8 ай бұрын
Mine loosened over time. Thx I’ll try this.
@cristian1708
@cristian1708 2 жыл бұрын
Thank you for sharing! Very useful! This should be the starting point of a proper laser calibration/alignment. Regarding the squareness between the x and y linear rails, do you think a 3d printed custom square would be accurate enough ?
@spaced-out-records
@spaced-out-records Жыл бұрын
super helpfull thankyou
@Coolmaaaaaan
@Coolmaaaaaan 2 жыл бұрын
I have a 1x1mtr diode laser machine with alignment issues.. and no one can tell me how to calibrate the rails.. its driving me crazy
@jppalm3944
@jppalm3944 Жыл бұрын
3,4 5
@jppalm3944
@jppalm3944 Жыл бұрын
Manufacturers should provide better maintenance tools.
Ramp Test and Optimal Focus for Co2 Laser
8:07
Bearded Builds Co
Рет қаралды 85 М.
K40 Laser fail on Y axis and make "knarking" noise
26:57
Weitling In The Garage
Рет қаралды 8 М.
Every team from the Bracket Buster! Who ya got? 😏
0:53
FailArmy Shorts
Рет қаралды 13 МЛН
Wednesday VS Enid: Who is The Best Mommy? #shorts
0:14
Troom Oki Toki
Рет қаралды 50 МЛН
Вопрос Ребром - Джиган
43:52
Gazgolder
Рет қаралды 3,8 МЛН
Align your K40 or Other Laser Cutter in 5 Easy Steps
12:08
Maker Monkey Industries
Рет қаралды 60 М.
Leveling the eBay 60 watt Chinese laser bed
9:40
Vintauri
Рет қаралды 11 М.
Diode laser square your gantry for better cuts with two tins of soup
12:09
⚡Flixmyswitch LASER ⚡
Рет қаралды 613
Square your X and Y axis - CNCnutz Episode 212
14:14
CNCnutz (Peter Passuello)
Рет қаралды 65 М.
OmTech Gantry Mechanics Part 2
19:30
Scottish Giant
Рет қаралды 582
I messed up my machine.. to show you how to fix it
19:42
The Clack Shack
Рет қаралды 6 М.
eBay Chinese CO2 Laser Cutter & Engraver -  Squaring and Alignment
10:49
Laser Maintenance - How To Square Your Gantry
6:19
Full Spectrum Laser (FSL)
Рет қаралды 3,9 М.
Laser Losing POWER?? Clean the lens!!
21:06
Paw Paw’s WorkShop
Рет қаралды 9 М.
Understanding Minimum power settings in lightburn
15:51
Computer Creationz
Рет қаралды 134 М.
Every team from the Bracket Buster! Who ya got? 😏
0:53
FailArmy Shorts
Рет қаралды 13 МЛН