How to stockpile material with a wheel loader

  Рет қаралды 148,368

VISTA Training Inc.

VISTA Training Inc.

Күн бұрын

Пікірлер: 23
@Mark-xm4sc
@Mark-xm4sc 4 жыл бұрын
I’ve never reversed Down a steep pile with a load. I’ve never felt nervous driving down a heap. Most of the time I’m going downhill empty anyway, but the bucket In front of you gives you stability. You can always drop the bucket to the ground if you start sliding or something.... even tipping the bucket back out and pushing your way down the material making a new ramp as you go. I’ve never rocked the bucket when loading the bucket either and never locked the lift lever in when going into a heap. You should be able to approach the heap, lift slightly and crowd back while moving forward all in a smooth motion and getting a full bucket. All those jerky movements just throw you around in the seat. I guess it’s the difference between being taught by an instructor, and being taught by an instructor that’s spent time actually operating them for a living first
@gilamonstermetalfabricatio569
@gilamonstermetalfabricatio569 7 жыл бұрын
Noel is correct in saying that this video is teaching incorrect procedures. One should never "pump the bucket" as stated add this puts unnecessary and damaging force in the front end of the machine.
@ultimumlibertas5727
@ultimumlibertas5727 7 жыл бұрын
There is absolutely no reason to lock the lift hoist lever when getting a full bucket. Just watch your RPM's and tires
@lloydstachoski3500
@lloydstachoski3500 6 жыл бұрын
Your bucket is the tool of the machine takes time you are then an operater!
@bitchwilly5311
@bitchwilly5311 6 жыл бұрын
Its called submarineing aproce pile as bucket arives at pile roll bucket out diveing (submarining bucket and as result filling buket to capasity faster
@beckymattz4987
@beckymattz4987 7 жыл бұрын
The loading method is wrong. Lift the boom a little, then start to curl the bucket. Depending on how hard the bank is, you may curl all in one step, or curl, pause, and then curl some more, repeating until fully curled. You may also need to continue raising the boom, but it depends on the material. NEVER "pump" the bucket by going back towards level. This unloads the tires and creates wheel spin, as well as unneeded wear and tear on the loader. Locking the boom in raise takes power away from the tires. In soft ground, you need to do that. On a hard floor, you need the power to drive into the pile, so that is why you don't lock it in, and pause in the curl, to drive in harder, but curl again before you get tire spin.
@blindabinda1234
@blindabinda1234 10 ай бұрын
Some materials you have no choice but to pump the bucket to get a good full bucket without taking forever. And if you let of the throttle while"pumping" the bucket you don't get wheel spin and it's not violent.
@suryadurai4127
@suryadurai4127 4 жыл бұрын
But experience operator teache me Bucket level may be bucket edge plate well damage he though me this we do it again and again He told me to open the bucket little bit And make take the cargo
@beaggyboy
@beaggyboy 6 жыл бұрын
Hi Peops, I'm just a regular guy who takes an interest in all things that's machinery related, in esp.vehicular prime movers of evry types. To all U Guys who work these Loader things like maybe day-in - day-out & knowin' 'em practically like as-if they were the figurative "Backs of Yer Hands" adage, I suppose it's safe to say. There's this 1 question that's been gnawing at me all this while & I've been meaning to forward this to all U Guys who is in the know. Why do Loaders of today or recent makes, all have cabs that sit with the engine on the rear segment of this articulative-steer system ? From what I learned, it seemed there was a certain survey held, some time way back in the 70's for the specific purpose of finding-out wic of the 2 segments, operators as Yerselves, wud rather the cab be on & Yor predecessors of that time by a majority, largely favored having the cab placed at the forward segment. So it then came to pass & was for a time thoughtful Wheel-Loader manufacturers then built quite a number their product based in accordance with that decision, with the likes of International Hough Loaders. I thought the same with likeminded loader-operators, the cab shud somehow be with or on the front-section of things, but it now seemed that that was not to be & that design had totally been altogether abandoned. I hope summa U pros in the know, who so happen to read on this article, coud maybe enlighten me a little on the pros or cons of why it is or not better for the cab to sit on the forward section & share Yor opinion on this subject. Please allow me to Tnk U Guys in advance fer yer time & attention in reading this commentary. Ave a good day or a nice evening ahead.
@TontoJive
@TontoJive 5 жыл бұрын
not as hard on the operator ,physically moving with the loader when placing or digging a bucket
@TontoJive
@TontoJive 5 жыл бұрын
also viewpoint and workability
@blindabinda1234
@blindabinda1234 10 ай бұрын
When the cab is on the front of the machine you then have to have a lot more hoses and wires going from the engine compartment to the cab and such. With the cab behind the articulated part you'll basically only have the 4-6 hydraulic lines that need to cross the articulating section.
@kadalivestream
@kadalivestream Жыл бұрын
4 speed and ram that shit
@brentthailand5742
@brentthailand5742 5 жыл бұрын
You might want to add to shift into first gear when you have a load on the front tires, so you dont overheat the torque converter and transmission in 2 nd gear,,, You will burn it out 2 nd gear is not meant for filling bucket pushing into a pile ,,, look it up in any owners manual.
@bhaskarbhatt7191
@bhaskarbhatt7191 4 ай бұрын
Please tell in Hindi while writing
@jakewalter3729
@jakewalter3729 6 жыл бұрын
B
@nealkosalski6901
@nealkosalski6901 9 жыл бұрын
Everything this video just said about loading the bucket is wrong.
@mimnaex7263
@mimnaex7263 8 жыл бұрын
Then what's the right way, don't say something is wrong and not give an explanation!
@bitchwilly5311
@bitchwilly5311 6 жыл бұрын
Yeah neil
@bitchwilly5311
@bitchwilly5311 6 жыл бұрын
O sorry neal
@johnobrien2207
@johnobrien2207 6 жыл бұрын
If you want a stock pile just dump and create a ram .Lifting a loader bucket up full takes time and danger .Plus loose material now and then if the heap is set .It makes for easier bigger scoops .Don t forget the knocking the loaded bucket before travelling to avoid dropping material on bumps .
Front End Loader
16:14
City of Hampton Safety & Training
Рет қаралды 68 М.
How to Operate a Wheel Loader - Advanced // Ep. 116
13:16
Heavy Metal Learning
Рет қаралды 110 М.
黑天使被操控了#short #angel #clown
00:40
Super Beauty team
Рет қаралды 61 МЛН
When you have a very capricious child 😂😘👍
00:16
Like Asiya
Рет қаралды 18 МЛН
Chain Game Strong ⛓️
00:21
Anwar Jibawi
Рет қаралды 41 МЛН
Каха и дочка
00:28
К-Media
Рет қаралды 3,4 МЛН
Cat® K Series Large Wheel Loader Operator Training
25:30
Cat Mining
Рет қаралды 266 М.
Basic Wheel Loader Controls Run Through
5:27
Dirt Ninja
Рет қаралды 315 М.
How To: Get a Full Bucket of Dirt In A Wheel Loader
4:29
Dirt Ninja
Рет қаралды 559 М.
Front End Loader Training - Top Mistakes | Heavy Equipment Operator Training
13:48
pay loader pushing up gravel and sand at the stockpile
13:34
ka-bucket tv
Рет қаралды 226
What NOT to do in a Wheel Loader | Heavy Equipment Operator
12:57
Heavy Metal Learning
Рет қаралды 375 М.
How NOT to run a Wheel loader - mistakes, errors and red flags
17:39
Stanley "Dirt Monkey" Genadek
Рет қаралды 381 М.
黑天使被操控了#short #angel #clown
00:40
Super Beauty team
Рет қаралды 61 МЛН