How to Test a Seat Belt Pretensioner How to know if Seat Belt Pre-tensioner is Good or Bad

[@WorldMechanics]

⛐ Check out our Garage to see what tools we use and recommend: www.amazon.com/shop/worldmechanics ⛐ Subscribe and hit the notification bell by the subscribe button for new videos: kzbin.info/door/J9xpq0qUZevSEdBSFqO2ow ⛐ Our GoFundme Page: www.gofundme.com/auto-repair-guys

[@paulusbaldy]

This guy is worth listening to and if he is addressing your problem in particular he will answer it well. If not it is always helpful,

[@hazelswains4438]

I've got a wh caprice 2002 that won't pass the pits cause the air bag light won't turn of. I've tried everything. I can't afford to take it anywhere. What do u suggest

[@hazelswains4438]

R BK I've got a wh caprice holden statsman that won't pass on inspection due to the air bag light staying on. I've tried everything

[@cristi9944]

Good morning I would like to ask you just for information, from the yellow connector if you widened the short circuit coffins with toothpick for example you could measure the pretensioner or it could explode thanks

[@hankthebugman]

This is a very good video. It was right on target for an issue I was troubleshooting.

[@viniciusguerra3364]

Very good video guys!!! Direct to the point.Helped me a lot, thanks. Greetings from Brazil.

[@Renegar87]

Great video

[@iflytango]

so where do you go if your scan tool says drivers side seat belt swith but the test with the meter shows good.

[@juanpena9386]

It's not "1", that means infinite, as in open circuit (infinite resistance)

[@didyouknow138]

Can you help me please, have accent 06 and got B1402- satellite sensor left side : Short to battery/ Intermittent, how to test the sensor, what reading should see thanks

[@mohamedabdelhalim9892]

i had the airbag lights on and i've figured that the previous owner had the pre-tensioner wires cut from the car loom itself is there a way to find out how to wire the two wires back. even manually

[@jorgedeleon7759]

Thanks that a very good video always watch it thanks

[@GrenPara]

Great Video! Thanks for making it.

[@semihyilmaz4699]

What is the purpose of shorting bar? The metal clips that touching both wires.

[@alfiestein7977]

Semih Yilmaz The shorting bar stops the pretensioner from being accidentally deployed. The one thing you never do is use a multimeter to test airbags or pretensioners unless you want a nasty explosion.

[@progers2810]

Lucky he was using a cheap shit multimeter!

[@benji7587]

@@alfiestein7977 Thanks for that tip but please tell me the correct way to test a Pretensioner?

[@alfiestein7977]

You don't test pretensioners. You replace them once the wiring and srs module are ruled out as possible culprits. Usually a scan tool indicates a code for a pretensioner fault (LH or RH). The pretensioner can be unplugged, removing it from the circuit. Then the vehicle wiring fitted near the pretensioner can be tested back to the srs module connector. You can swap pretensioners to help isolate the fault. We would sometimes buy used from a breakers yard (older cars) making sure the unit hadn't been deployed.

[@dailygrinders89]

my seatbelt pretensioner wiring has been cut from the seat sliding back and forth and has caused my airbag light to come on. I have a 2006 Ford crown victoria police interceptor. can I just buy another one or does the computer have to be flashed or something to recognize it

[@Mordorer]

Nah just replace or repair the wiring but always make sure your battery is off.

[@shelbado]

This guy has the best accent I've ever heard

[@hectorheath]

Thanks BORAT

[@dLikesDDs]

gold plated pins...cool

[@dronestuff3431]

I want to buy your bracelet.

[@FREEAIR_1973]

que bueno, thanks!!!

[@PushyPawn]

I just wanted to see it pop.

[@lard1892]

You're not supposed to ohm out a airbag or any tensioner with a ignitor....Where did you go to school?

[@andredesousa96]

Whats the proper way to do it? I'm going about fixing my airbag light on my car

[@bobolulu7615]

Rubbish. You can test anything like this with an ohm meter. It's not like the meter is putting out heaps of volts and amps. Ohm meters are high impedance and this will not set anything offl

[@rdgamer4256]

How can I contact you

[@tannerh151]

Oh my God your English is horrible. And you have three or four channels that run the same video. You cover up good videos by creating multiple channels.

[@LubomirPotocki]

What languages have you already learnt dude? Maybe you should present us your skills.