Good info boss,,malaking tulong yan. Pero linawin ko lang po yung sabi mong zero reading(0) sa pin 1 and 22, hindi zero ang reading kundi OL (Open Line). iba kasi ang Zero(shorted) sa OL (ope nline) boss.
@eliezercatseye1298 Жыл бұрын
salamat sir sa tips and trick na pinakita mo. malaking tulong 'to para iwas sira sa logic board ng printer. nakailang palit na rin ako ng transistor at power ic para lang gumana ulit ang printer ko.
@losermons Жыл бұрын
Nice one sir, hirap to gawin pero ikaw nagawa mo pa e share god bless sayo.. iwas sira na sa mga logic board natin,
@kimwenceslaosanchez44493 ай бұрын
Salamat po sa info ninyo na ito at malaking tulong
@walakotv74512 жыл бұрын
Thanks for this Master laki tulong nito as Reference,New subs👌
@adriano-rj3733 Жыл бұрын
Firstly, congratulations on the channel, and may God bless you! So I was confused, did you say pin 22? This pin refers to the print head of which printer? I ask because I recently removed one from the L120 and noticed that it has 21 pins!
@murphybonaobra3565 Жыл бұрын
thanks po ..laking tulong ..new learning nanaman.. eh what if po ang reading nung 2nd pin ay 2.220 up to 3.100 sumthing ?? ganyan reading po nung sakin wew
@pangfei81142 жыл бұрын
It seems that gilded plate has to be glued not with two or three dots of glue, but with lines of glue to prevent ink leakage from channel to channel.
@santiagomasapol9415 Жыл бұрын
😮😮😢😢😮
@sanchezmarlonc.9398 Жыл бұрын
Good day po sir, tanong ko lng po kung saan po kayo bumibili ng print head ng epson, particular po ung head ng L5290 series. Thanks po
@c2sartinkprinthub757 Жыл бұрын
this is very informative.. lahat po ba ng head ganyan ang configuration?
@wayneslink Жыл бұрын
Only applicable sa same series basta ganyan porma hehe
@adrianabelinde1262 Жыл бұрын
saan o nilalagay ang point ng multimeter if Sanwa YX360TRF kung mag check po ng head ng printer? Thanks for positive response medyo baguhan palang po kasi sa industry ng repair ng printer..At nakaaus na po ako kahaon ng printer na may general error..Thanks and more power po sa page nyo..
@wayneslink Жыл бұрын
Diode mode po. May sign yan yung may arrow
@adrianabelinde1262 Жыл бұрын
@@wayneslink salamat po sa info sir..
@joshuaespinosa94065 ай бұрын
sir pano kung pin number 2 OL reading din pag dating sa 3 okay sya ,okay pakaya salpak to sir
@lmreasytechliving2 жыл бұрын
Other printhead has 20 pins only, like T13 or L120. Rule of thumb probably is both ends should have no readings.
@adriano-rj3733 Жыл бұрын
Quité un cabezal de impresión de la Epson L120 y ¡hay 21 pines!
@knowellbrenflorentino68592 жыл бұрын
Goods na goods bro, dahil dito nalaman ko na yung 3 head ko ay okay pa. Pero sa kasamaang palad sobrang barado buhat ng pigment sila.
@knowellbrenflorentino68592 жыл бұрын
Maraming salamat wayne. God bless u.
@wayneslink2 жыл бұрын
Welcome bro no probs
@lagosite4 ай бұрын
San po kayo bumibili ng replacement parts?
@mehmanqurbanov30422 жыл бұрын
İ have epson wf 2530 . My headprint value pin 1 is 0 pin 2 is 678 and pin 3 is 583. It can be normal for my device ?
@ezbonmworiathemaker41902 жыл бұрын
Hello bro. I found this channel and already subscribed. I don't understand the language I nomally blow mother board as a way of testing the printer heads like the ones you are testing. What is the condition. For a good printer head that is okey The ones that reads pin 1 and 22 =650 Value.? Thank you for the opening Scripture. Finally I got it after repeating this video several times. Please bro share how to test printer head for L850/T50/T60/px660. Models. Thank you.
@Hawkman000682311 ай бұрын
Hello and God bless you for what you are sharing. I have a DTF machine uses the I 3200 printheads I have red light on board and have replaced flat head cables carriage board and main board and swapped heads. Can i test the printheads like you did to see if they are good. Or is there something else that you know of that could cause red light on Honsoft v. 143 board. I subscribed thanks for any help. 100 US dollars if you can help me and I will gladly pay it.
@raymonddicimulacion26911 ай бұрын
Idol sa l3110 ground point pa din ung dulo na pin?
@tyrellwreleck4226 Жыл бұрын
Kaya pala pumutok yung fuse ng epson L4160 ko. Chineck ko, shorted nga. Umorder po ako sa shopee ng printhead, 1k lang. Update po ako kung okay yung printhead pag nareceive ko na. Anyways very helpful po yung video. Balak ko kasing ibalik yung printhead pagka solder ko ng fuse. Lifesaver po kayo.
@wayneslink Жыл бұрын
Nako dilikado 1k 😂
@tyrellwreleck4226 Жыл бұрын
@@wayneslink preferred seller po sya at mataas naman rating. Isend ko po link?
@tyrellwreleck4226 Жыл бұрын
Update, so walang short dun sa print head. Pero nung ginamit ko nag error sya 4000 something ang lumabas. Tapos nung inulit ko, nasira yung mosfet ng board at may shorted capacitor. Oorder ako ng bagong mosfet and check ko ulit kung gagana. Dalawang mosfet ang nagshort.
@markkat597011 ай бұрын
Hindi naman yung board sumisira sa printhead no sir? Yung mismong printhead pwede maka damage ng board? Nagka error code kasi ako printer error 31006 nung test ko yung printhead shorted na pero ang sabi daw yung errror 31006 sa mismong fuse daw sana matulungan nyo ako sir thanks
@jgquintana24 Жыл бұрын
Saludos desde Perú, gracias
@DennisRV2 ай бұрын
L210 huling print ay nozzle check, tapos iniwan ko naka standby.. maya maya no power na. binaklas kona mmainboard, pagtest ko sa transisto shorted na mga transistor. kala ko okay na nung nag nozzle check... huhu mahal pa. naman ng ic
@wayneslink2 ай бұрын
Mura lang transistor P200+ .Mostly ma busted ang transistor including fuse dahil sa shorted printhead so mapa gastos ka ninyan.
@joshuacasador40332 ай бұрын
@@wayneslink kaya pabang ma ayos ang printhead sir? if shorted na?
@wayneslink2 ай бұрын
Di na po. Need na yan palitan.
@joshuacasador40332 ай бұрын
@@wayneslink na check kopo dipo pala shorted, pero ang color red nya clogged po ano pong best pang tanggal ng clogged na ink sir? thanks po.
@lenttaofreedom2058 Жыл бұрын
Hello bro. Do you know the L200 series? I noticed that pin 20 has low resistance 0. Could this be normal?
@wayneslink Жыл бұрын
it could be, rule of thumb, if the printer dies then you know the head is dead lol
@roderickacob11622 жыл бұрын
Sir yung printer na no print out . Ok pa naman yung fuse f1. Anu po kaya possible na sira po sir? Ty
@markanthonyguevarra9167 Жыл бұрын
Sir pano pag sa pin number 2 nasa .550 tapos sa 3 450 lng reading ok p po b un?
@glenncabonita37832 жыл бұрын
Same lang din po ba process nyan sa ibang head. Like Epson L1800
@wayneslink2 жыл бұрын
Hindi po magkaiba sila
@rediyproject2 жыл бұрын
Sir ano po transistor ang nasisira sa eposn 1400 pag short ang head. Salamat
@anthonylastra78642 жыл бұрын
Possible Po ba na head Ang problema pag fatal error Ang nakalagay
@user-hq3vz5tk1f2 жыл бұрын
Thank you lods, dagdag kaalaman
@wayneslink2 жыл бұрын
Wc po. Don't forget to like and subscribe for more updates 😊
@user-hq3vz5tk1f2 жыл бұрын
@@wayneslink Done na po sir. abang lang po ako bago mo vids para about repair para ma tuto din ako.
@knowellbrenflorentino68592 жыл бұрын
Bro bakit kaya yung printhead ko upon using tester okay naman same ng palo gaya sayo pero yung sinaksak ko na no printout? Possible kaya yun sira na kahit tama naman reading?
@mikaelcruise66518 ай бұрын
Boss compatible ba ang print head ng epson L120 sa L360?
@wayneslink8 ай бұрын
Same bos
@matteyjackson6388 Жыл бұрын
Sir try ko test yung head ng L120 , L220 at L360 ko gumagana ng maayos kahit may readings sa 1st pin, hindi ba delikado na gamitin?
@wayneslink Жыл бұрын
pag nagamit pa may resistance pa yan kunte,
@matteyjackson6388 Жыл бұрын
@@wayneslink So ok lang ba sya gamitin? mag 1month na sila ngayon
@ricochoricz56933 ай бұрын
boss narerepair pa ba ang printhead if shorted na? mahal kasi printhead ng epson 2k+ parang bumili na rin ng brand new.
@wayneslink3 ай бұрын
Di na po. Palit na yan
@nemmrm67017 күн бұрын
Depende sir. May inayos nako nyan ginamitan ko ng microscope. Nilinis ko yung mga pin ng printerhead kasi mga sunog. Ginamitan ko din ng jumper mula sa flex. By God's grace naayos sya. Na short yun kasi natapon yung mga ink sa circuit ng printer head.
@wayneslink5 күн бұрын
Minor lang yan pag linya lang naputol dahil sa sunog at kadalasan pag nacut agad yung linya ng flex at head swerte pero malabo yan nasa 1/10 lang yan mangyayari base sa experienced ko.. Pag full short walang pag asa yan palit na kesa marami pa masira sa board.
@benedicespino7878Ай бұрын
binilang kopo pin bakit 21 lng sakin l120 po head....???
@clintdomz65632 жыл бұрын
Daghang salamat kaayu brod
@mayetnovesteras67242 жыл бұрын
Pag nabasa ba yung print head posibli po bang masira?
@wayneslink2 жыл бұрын
Yes po
@mr.bluetubetv60073 ай бұрын
Nag subscribe ako sa channel mo boss ha..
@wayneslink3 ай бұрын
Ty boss
@jaysonrasonabe91142 жыл бұрын
Sir saan po makakabili na print head Epson L3210 salamat po sana ma notice po
@The27czoko Жыл бұрын
how can measure l1800 bro
@lmreasytechliving2 жыл бұрын
Very good!
@motivationvideos2235 Жыл бұрын
Same lang po ba ng process l120 head?
@wayneslink Жыл бұрын
same lang yan
@cornelioagojo6785 Жыл бұрын
sir epson L3110 po blink blink po sya
@wayneslink Жыл бұрын
Baka reset, anung nakalagay sa screen pag mag peprint ka? Marami akong video sa channel blinking lights l3110 baka anjan ang solution mo
@cornelioagojo6785 Жыл бұрын
pag blink blink ang ilaw ano po kaya problema sir
@wayneslink Жыл бұрын
Anung unit model pp?
@tonlekhmermovies1725 Жыл бұрын
Good explain
@tonlekhmermovies1725 Жыл бұрын
I want you make more explain about Epson l1800 printhead.
@angelmontes18853 ай бұрын
8550 how to?
@MrBRUNZING2 жыл бұрын
Ma aayos ba ang print head kahit na short na cya dati?
@wayneslink2 жыл бұрын
Hindi na at never try to reinstall, masisira lang board mu bkss
@otakudesu9901Ай бұрын
Sir. Paano naman itest kapag analog multitester ang gamit?
@wayneslinkАй бұрын
Same lang din po. Base lang sa deflection reading
@otakudesu9901Ай бұрын
@@wayneslink basta po may palo? Tama ba? Nung nag check po ako. Sa 'PIN' 3 po. Walang palo (reverse polarity) Pero nung correct polarity po ginawa ko pumalo. Naguluhan po ako kung buo paba? Sa PIN 0/1 po, hindi pumalo. (Good) Sa Pin 2 pumalo. (Good) Sa Pin 3 lang po talaga
@AldrinDelaCruz-n1s8 ай бұрын
Salamat sir new subs po ako sa inyo. bka may head ka jan sir na clogged n di pa short pabili po kht super clogged n sir bka sakali lng mka buhay pa kht isa
@anthonyepanaguitontm1-css445 Жыл бұрын
Sana Po sa analog Meron kayo
@jinujain12 жыл бұрын
Plase make video l800 or l1800 6 colour head testing
@ElektroTech842 жыл бұрын
Hello my friend. Your work is very successful, I follow it with pleasure. I have an Epson L3150 model printer and I would like your help with a paroblem. First of all, the power was lost while my printer was running, during the checks I made, I found that the parts of A2222, C6144 and E09A7418A were broken and I replaced them. however, when I power up and try again, a few seconds after the screen lights up and the motors kick in, the motors stop, and then my power supply goes into short-circuit mode to protect itself. What could be the source of the problem? I will be glad if you can help.
@wayneslink2 жыл бұрын
That is because the cause is the printhead. You need to replace transistor and power ic and printhead for that
@ElektroTech842 жыл бұрын
@@wayneslink In the measurements I made as in your video; Stand #1: no value, stand #2:0.625v, stand #3:0.555v. What values should I see for the other feet and how can I tell for sure that the printhead is bad?
@bulentborasuyabatmaz2 жыл бұрын
Merhaba Serdar Bey; Ben de aynı dertten muzdaribim. Kafa temizleme girişimi pahalıya mal oldu. Temizlik sonrası yazıcı 5-10 saniye çalıştı ve durdu. Bir daha çalışmadı. Benzer çok sayıda sorun gördüm internette. Transistör değişim, gerekirse entegre değişimi yapacağım bende ancak kafa sağlam mı? değiştirmek zorunda kalıt mıyım? vs vs... Siz neler öğrendiniz bu süreçte?
@ElektroTech842 жыл бұрын
@@bulentborasuyabatmaz Merhaba Bülent bey, yaptığım işlemleri siralarsam eğer; -Yukiradaki bahsettiğim güç taransistorleri kısa devre olduğu için değiştirdim. -Yukarida bahsettiğim entegreyi kontrol ettiğimde sorun olmadığını tespit ettim. -Anakart üzerinde F1 olarak adlandırılan sigorta direnclerini kontrol ettiğimde sorun yoktu -Son olarak yazıcı kafasını Hint videolarında tarif edildiği gibi direnç kademesinde ölçüm yaptım onda da problem yoktu fakat yazıcı kafası bir ay kadar süre dışarıda kaldığı için gözenekler tıkanmış açmayı başaramadım. Sonuç olarak yazicim normal olarak çalıştı ama sanırım yeni bir kafa almak zorunda kalacağım galiba. Bunların yanında yaptığım araştırmalarda kafa temizligi yapıldıktan hemen sonra yazının kullanılması transistör, entegre, sigorta ve yazıcı kafası dahil hepsini bozuyormus. Hatta kafaya bağlı olan Flex kablonun bağlantı noktalarına veya iç kısımlarına zarar verebiliyor Muş, o yüzden kablonun sağlamlığını da kontrol edin derim. Epson ile ilgili Hintli yayıncıları takip edin, çeşitli arızalarla ilgili bir çok video var.
@bulentborasuyabatmaz2 жыл бұрын
@@ElektroTech84 Teşekkür ederim. Çook video izledim. Transistörleri sipariş ettim. Entegre, kablo ve kafa sağlam gibi duruyor. Yarın veya sonraki gün malzemeler gelir, sonucu göreceğim 🤷🏻♂️
@daddiyproject84212 жыл бұрын
Pano pag walang reading lahat ng terminal?
@deathplaystv4289 Жыл бұрын
Boss paano pag sa second 000 ang labas at beeping
@roelabello394 Жыл бұрын
boss pano pag mababa kesa 650 ex. 5xx
@crimartv2 жыл бұрын
Ayus bai
@user-gt6us9px9m9 ай бұрын
sir pde pa poh na mgwa ang printer head
@wayneslink9 ай бұрын
Di napo pag malaki na tama
@user-gt6us9px9m8 ай бұрын
@@wayneslinksan poh loc. nyo poh
@rhimecaquilala6916 Жыл бұрын
Ano mga cause ng shorted sir?
@wayneslink Жыл бұрын
Liquid damage
@rhimecaquilala6916 Жыл бұрын
@@wayneslink salamat sir God bless po
@JohnRhellyEwayan-mf6to Жыл бұрын
pano mg,disassimble ng head
@dtechdiytutorial Жыл бұрын
san po buy ng power ic
@wayneslink Жыл бұрын
Nasa online lang
@maximeathene1385 Жыл бұрын
Can you make subtiles please sir?
@wayneslink Жыл бұрын
Yes next time
@timlarsen3312 Жыл бұрын
@@wayneslink thank you Sir, will the subs be in English, since i do not speak Tagalog, or could you provide us a link where we can find specs. and test readings for the printheads, i have a L210, thank you very much
@wayneslink Жыл бұрын
Welcome ans thanks... I have a video try to search on my channel titled " how to test epson printhead using multimeter tester "