how to upgrade toy cars, The steering is powered by a pulse.

Рет қаралды 58,017

Күн бұрын

Пікірлер: 38

@zingerzte4192 11 ай бұрын

This is the video with the most amount of views you got, I think you should focus more on modifying this toy car because there are many people who like these cheap little cars and want to upgrade them

@motor5 11 ай бұрын

Thank you for your opinion. It's a very helpful opinion for video production. I'll actively refer to it.

@zingerzte4192 10 ай бұрын

31k, that’s a pretty nice number of views. 50k and a 100k next?!

@motor5 10 ай бұрын

I'm happy that you watched more than I tried

@motor5 Жыл бұрын

영상에서 교체한 모터는 전자파 간섭 방지기능이 있는 모터입니다. 아두이노 계열은 이 기능이 없는 모터를 사용하면 CPU가 다운되는 문제가 발생합니다.

@fredwester4336 Жыл бұрын

Did almost same thing...only I use a micro servo for steering. For the motor I use a 30000RPM at 3volt motor (yes a 3 with 5 zero's). Electronics, the same as you use. An esp32 c3 and a l298n for motor driver...big fun with these cheap cars.. Remote also an esp32 c3 mounted in an old 27Mhz rc transmitter. connection via p2p wifi (read somwhere you use BT)

@antonnicolae20 11 ай бұрын

hei man, do you think you could give me some links or schematics on how to use them, I've started a build of my own with of the shelf parts but I would like to make a piece that will be more reliable

@motor5 11 ай бұрын

@@antonnicolae20 It's hard to explain. I'll show you what I'm making in more detail next time.

@zingerzte4192 11 ай бұрын

Can you do more modifications in this car? like proportional throttle and steering? What is I rewind the wire in the motor with a thicker wire?

@motor5 11 ай бұрын

I'm going to buy a similar vehicle, and try different renovations. Thank you for your comments.

@vasilyy21 Жыл бұрын

May I know the purchase link for the receiver and motor driver? Do you use the original remote or replace it?

@motor5 11 ай бұрын

Do you know Arduino? I code and use Arduino program. CPU is ESP32c3. It receives data through Bluetooth and runs motor driver. Communication data is "RC,steer,throttle". Steer and throttle are from -255 to 255. Example) RC,0,255 This is neutral steering and maximum throttle. I also make and use the controller with ESP32. It sometimes appears in other videos of me. The parts were purchased from AliExpress.

@jeffreyhickman3871 11 ай бұрын

I’ve noticed that the steering motors in these cheaper RC cars, works by a pulse. On more expensive RC cars, the front wheels turn gradually to the left or right, along with the noise of the steering motor. I just found out about this on eBay, very early this morning. A Mockingbird slot car drag racing motor, which turns out 65000 RPM. This motor probably would get your cheap RC car going at least 70 MPH. I’d put 2️⃣-9-volt batteries in series, as an upgrade. You’d have to reconstruct the battery compartment of the car, as well as the motor. I think 🤔 that the steering motor would be okay 👍. Circuit boards in the car would be your next upgrade, because I think 🤔 the 18 volts, provided by the 2️⃣-9-volt batteries, would probably burn your circuit board 🆙. It would also shorten the life of the car’s original drive motor, and may possibly start your RC car on fire. Just subbed!! Your friend, Jeff.

@motor5 11 ай бұрын

Thank you for the good information

@ashtaron23 11 ай бұрын

are you using the same controller with the new receiver or did you get a new controller for it?

@motor5 11 ай бұрын

See the video kzbin.infoybT9owen73A

@broctonnunns280 Жыл бұрын

Do you have a parts list for this? Like what motors and receivers you are using? thanks! :D

@motor5 Жыл бұрын

The steering motor used the body and magnets of the 3v motor, and the rotor used the rotor and carbon brush of the electromagnetic interference prevention motor. The receiver is ESP32's Bluetooth method.

@jadumate Жыл бұрын

와 이건 정말 멋지네요 So cool !

@motor5 Жыл бұрын

감사합니다 ^^

@GF-mf7ml Жыл бұрын

I only change center drive shaft rear gear (it crack) just 1 tooth less than front, enough for counter steer.

@motor5 11 ай бұрын

use original gear. same tooth

@matigamer9681 10 ай бұрын

Can you send me link of this products for upgrade?

@motor5 10 ай бұрын

Parts Link Search AliExpress as follows 1. 1. esp32 c3 super mini 2. 2. TA6586 3. 3. FP130-CN-14160 The rear motor is missing the link.

@oswelbaltodano6439 11 ай бұрын

Buen video jna pregunta si tengo el transmisor no original del reseptor sera que puedo ponerlo con otro coche ayuda

@motor5 11 ай бұрын

I made and used the transmitter receiver myself. I put it in various toy cars and use it.

@oswelbaltodano6439 11 ай бұрын

@@motor5 But yes, what I'm asking you is possible, I mean, if I can put the transmitter from a different receiver with another one, that's what I was referring to.

@matigamer9681 10 ай бұрын

Could you send me a link to these products?

@motor5 10 ай бұрын

Parts Link Search AliExpress as follows 1. 1. esp32 c3 super mini 2. 2. TA6586 3. 3. FP130-CN-14160 The rear motor is missing the link.

@matigamer9681 10 ай бұрын

@@motor5 thanks

@MShahid-ux1zj 11 ай бұрын

Can you please show how to make that receiver ??. Please

@motor5 11 ай бұрын

There are many ways to create a receiver. Arduino, Arduino Nano, Arduino Pro Micro, ESP32, There are ESP32C3 and so on. There are many types of motor drivers available. The receiver of the video was made using ESP32C3 and TA6586 chips.