How to use CKCS BS01 Mini DC-DC Step Up Module and full review.

[@philbateman1989]

Thanks for making this easy to understand and informative even though I don't speak your language! Very helpful :)

[@nishantharohana6048]

Explanations are cristal clear. Keep up the good work 👍

[@theelectroroot4919]

thank you bro 🤜🤛

[@densilfernando5937]

සුපිරි පැහැදිලි කිරිමක් ඉදිරියට යමු ස්තුතියි

[@theelectroroot4919]

බොහොම ස්තූතියි

[@crazynima1223]

Next level 😊❤️

[@theelectroroot4919]

thnx bro

[@albertocassio2854]

Sounds perfect to me, just worry about removing the connection on A B pads. I have bad memories of trying to connect the external antenna on ESP32-cam board and making a mess of it!

[@theelectroroot4919]

Yes, those pads are very small and using too much heat will remove all the pads from the pcb. You can use some jumper wires to make connections from A to B at your convenience. Anyway, thank you so much for sharing your experience 👍

[@sanshan1980]

Thank you so much

[@gatitomono47f77]

Would It be possible to Bridge the soldering points using an HB pencil to make a Bridge bettween eachother instead of soldering

[@shehanlee5844]

Good one 👏

[@theelectroroot4919]

thank you 🤜🤛

[@vkgaming5377]

Does it heat too much

[@gelioyakandy]

Super ...

[@theelectroroot4919]

thank you very much 🤜🤛

[@densilfernando5937]

භෝද පැහැදිලි කිරීමකි දෙවි පිභිටයි බුදු සරනයි පුතා

[@theelectroroot4919]

බොහොම ස්තූතියි ❤️

[@SMEHUYOK]

Янги хынд киноларда!

[@saifultechbangla]

Please let me know how to 9 vold output mistakes

[@nimanishara2248]

❤️

[@theelectroroot4919]

🤜🤛

[@dlakshan3578]

❤❤

[@alb9070]

Hi can I use this in conjunction with a TP4056 module? I want to have a single 18650 inside my enclosure able to deliver 12v 0.3A to a motor, and then at the same time be able to charge the 18650 by opening the enclosure lid and plugging 5v power to the USB C port, is it possible? I know the video recommends not to discharge while charging, is there any other reason why they won't work together?

[@theelectroroot4919]

If the current required by the motor is 0.3 ampere, it can be used without any problem. But you have to manage the heat with time of use. It is not good to charge the 18650 battery with tp4056 when taking the load. Because the safety features don't work properly when charging like that. It would be good if the charging time could be reduced while carrying the load. Because 3.7 volts increases to 12 volts, the boost module can overheat. If so, use a heatsink

[@salar908]

Can this module be used for the sim800l module? According to the required amperage of SIM800l, is this possible?

[@shahbhai2432]

I want to use 18650 5 to 8 cell for 9v wifi router. How many i can use with this module and Does it have any battery low protection.

[@Zorema_Hnamte]

Is it safe to connect these modules in parallel to have more ampere output at 12v? And where do we need to put heatsink?

[@theelectroroot4919]

Paralleling more modules is not recommended. If more amperage is required, use a different boost module. Install a heatsink on the underside of the module close to the coil

[@Zorema_Hnamte]

@@theelectroroot4919 Which boost module do you recommend?

[@theelectroroot4919]

It is decided according to your needs. The XL 6009 module is good as a buck boost conveter. Or buy a 400W stepup module and you can adjust both constant current and constant voltage with 400W module

[@elni9899]

WiFi ups and DC booster together work ? say in .

[@Sabbirhossain69812]

Bro this module restarting automatically. Why this is happening. My router almost dead for this

[@iginorienzo2347]

Can i input 9v and output 12v from this

[@theelectroroot4919]

yes you can 👍

[@dlakshan3578]

ඔයා ගත්ත 1s bms එක හැර, tp4056 හරහා දුන්නත් කමක් නෑ නේද ?

[@m.m.ifernando7184]

how much and where i can buy?

[@theelectroroot4919]

eBay or aliExpress

[@shaikhirfan6935]

Input 14v. Yes, No comments reply sir