How to Use Egg Incubator Part 2 (Automatic 48 Egg Hatcher)

[@emilyhale7551]

I have the 48 egg incubator and it won’t stop beeping like the temp or humidity is too low, but they’re perfectly fine

[@shannoncothern9131]

How do you disable the beeping alarm

[@beverleywylie530]

Help with the water filling please for this machine. Do we fill all channels or just outside ones. and how does the outside water hole fill up when it only goes to a small square

[@JoseReyes-iw4bk]

Been asking same question for past years. No reply.

[@lallorona6014]

You can use a wet sponge and keep adding water to the sponge as needed. Just ask Bob

[@liisarich7978]

Add very little water. Right now, I add 1 teaspoon every 1.5 hours. This is the only way it works ..

[@redsaens2823]

I just use a straw and syringe to add water through the side. Thus far, I've seen on a blog that humidity problems do occur. The owner of the blog recommended to dry test a small batch for the 21 day period. For me:; My humidity fluctuates. I added roughly 4 syringes of water and the humidity rose from around 47 to 58 been around the 53-58 range for the past 8hours. Aiming for 55 humidity with temperature of 38.1 Celsius. I will get the syringe measurement and post back here. Note that my incubator is housed in a Styrofoam box to help with heat management. I'm actually experience a lot of heat drops. Usually from 38 to 37, maybe 36.

[@satishganvir2024]

How many watter ad this and wich areas

[@ezequielmendoza9790]

I have the 24 egg incubator. What are the two small yellow bits for? I’m not sure if eggs are being rotates

[@bsudheer24]

Hello Today I purchased this product,I had many doubts,how can I contact u for clearing my doubts, Product came without assembled,I don't know to assembling processing, And how much water add in it &how can add Egg rotation is not working.

[@robynmiller3037]

Mine keeps saying L. What does it mean?

[@KCxx2]

This may help from the manual which is a little difficult to understand. I don't believe there is a high / low setting for humidy, just one setting. If I discover differently I will try to update this note. Display Description Factory Settings AL Setting low temperature alarm 1°C (33.8°F) AH Setting high temperature alarm 1°C (33.8°F) AS Setting humidity 60% CA Calibrating temperature transmitter 0°C (32°F) HS Setting upper temperature limit 39.5°C (103.1°F) LS Setting lower temperature limit 30°C (86°F)

[@thecakeladytm9962]

Thank you

[@Lady_C83]

How do we set date again?

[@liisarich7978]

You do not need to touch this, so you knock the settings, but you do not adjust the humidity and temperature. So only the digit is regulated, which means when the signal will go. But you cannot regulate the temperature or humidity itself. But to set the temperature, just briefly press the upper button on the left and select the desired temperature with the up and down buttons. Do not do anything with factory settings, where CA and other letters!

[@lafamiliadeacero1577]

Does anyone know how to stop the beeping sound ? It’s all night long

[@Serkanylmaz_61]

hello first I did this machine I first gave a space with the paper of the machine by the uct and the humidity 55 I found 37.7 at this temperature I have set this exact solution machine normally 38.2 temperature with this negative second if the moisture content of a bolumude full of 65 I find what I do This is because the air wave from the top of this machine cannot be fully removed and there will be no problem. Heat from 50 to 55 humidity for chickens 37.7. At the end of the first 18 days of development will be heat 36.7 humidity 70.

[@mtkkuluckaTuncay]

Merhaba Bu kuluçka makinesinde fanlar neden zemine doğru üflemekte ?

[@sunny_lifex6600]

I have an incubator but in the night it always wakes me up with a low temperature alarm. Does anyone know how to turn it off permanently?

[@christinagrimmett4129]

My humidity keeps flashing 62 how do I get it to stop, also how do I set the day counter for chickens?

[@imaramentertainment1162]

please tell me the normal temperatur and normal humilidy of this incubator

[@redsaens2823]

For me, the incubator came at 35 Celsius with Humidity of 50. But your settings would depend on the egg you are hatching. I'm from the Caribbean by the way. Temperatures might vary.

[@saeedsafianu893]

How much watts or voltage is the heating element.

[@pabbathireddysanthoshreddy5731]

How much water we use in this incubator?

[@lauramcnaughton664]

The alarm is going off every few minutes! Humidity (57) is flashing. Why is it going off? How do I make it stop!

[@sophiageralis3863]

Did u figure out how to stop?

[@Mrrevrendcrow870]

I can’t find where or how to change the humidity levels and alarms. I do dry hatching and need to with this one!!! Can someone please help since ive just read we got dropped on a how to #3??

[@liisarich7978]

Add very little water. Right now, I add 1 teaspoon every 1.5 hours. This is the only way it works ..

[@JuanMendoza-cr4bo]

are you sure.

[@rodalyngale4328]

how to turn off the automatic rotation on the 18th day? it still rotates aftr 18th day of incubation.

[@akashpersaud5546]

Disconnect the Turner

[@deonmuller3717]

Hi. Can you please help me with the names of the following and what it is used for. HD, HU,LS,HS, CA, AS, AH, AL. Kind regards

[@zahrasandher3643]

how do we adjust humidity

[@TheLAShop]

Default is 1C , to change it: Hold the Settings button down for three seconds then you will want to go to the AH menu selection from there you will want to move the numbers up to your desired HIGH temp threshold. And repeat the process for your Low temp in the AL menu selection

[@liisarich7978]

Add very little water. Right now, I add 1 teaspoon every 1.5 hours. This is the only way it works ..

[@liisarich7978]

@@TheLAShop You don’t need to touch it, so you knock the settings, but you don’t adjust the humidity. So only the humidity figure is regulated, which means when the signal will go. But you can't regulate the humidity itself. Humidity can only be regulated by the amount of water that you add.

[@suzannehammond7119]

Have got the 12 egg incubator .. does anyone know if there is a demo video for this?

[@patrickmahugu5349]

How much for 45 eggs incubator

[@eleonoramarchello6859]

Can anyone tell me what the three different parameters (AS AL and LS) are? Thank you in advance!

[@acngyn]

AL - setting low temp alarm AS - setting humidity LS - setting lower temperature limit

[@liisarich7978]

You don’t need to touch it, so you knock the settings, but you don’t adjust the humidity. So only the digit is regulated, which means when the signal will go. But you can't regulate the temperature itself. Just press briefly on the top button on the left and select the desired temperature with the keys up and down. Do not do anything with factory settings, where CA and other letters!

[@tonmoyphukan]

After working for 6 months, the Incubator temperature inside does not increase from 33.6/33.8 in the display. What is the reason? Is the fan a problem.

[@liisarich7978]

You do not need to touch this, so you knock the settings, but you do not adjust the humidity and temperature. So only the digit is regulated, which means when the signal will go. But you cannot regulate the temperature or humidity itself. But to set the temperature, just briefly press the upper button on the left and select the desired temperature with the up and down buttons. Do not do anything with factory settings, where CA and other letters!

[@AtifAli-yx6bm]

Are you supposed to turn the eggs or is it fully automatic, thanks

[@tiredhero]

automatic

[@AtifAli-yx6bm]

@@tiredhero some ppl suggest turning the eggs twice a day additionally?? But my hatch rates always been low so want to try something different

[@tiredhero]

@@AtifAli-yx6bm would probably be better fully turning them your self as these only turn about 45 degrees... i made my own incubator before and got better hatch rates than using this... but i didnt turn them my self but that was quail eggs i used im going to try some silkies and other bantams soon in this one see how it goes turning them my self...

[@AtifAli-yx6bm]

@@tiredhero tbh ive litterally just put 24 eggs in the incubator now and hope for a good hatch rate but usually get like 50% but the time i used eggs from my own hens i had a much higher hatch rate

[@tiredhero]

@@AtifAli-yx6bm so i binned the incubator and made one with a inkbird a heat lamp and a styrofoam box.. hatched 5 out of 5 but lost one.. so ended up with 4 chicks... best hatch rate i have had..

[@Nasirtoys1]

I need 48 egg machine how much

[@AudreyxEdits]

How do you stop the automatic turning

[@davescopes249]

Unplug it. Or unplug it and take it out.

[@denisevespescu6353]

I am wanting to know how much water do I put in the bottom of the incubator do I just put in the middle section or do I do the whole perimeter need answers asap thanks

[@anetdsouza3919]

How much water to be used in 48egg incubator

[@liisarich7978]

Add very little water. Right now, I add 1 teaspoon every 1.5 hours. This is the only way it works ..

[@alilatif8929]

How to decrease humidity ???

[@joycenesselhauf2820]

It would be nice if I could understand half of what is being said.

[@ericaelliott1516]

what are the temps this incubator should be and humidity

[@jessemarvinvelarde8331]

Same question here.

[@liisarich7978]

@@ericaelliott1516 I do everything at a temperature of 37.7-37.8 approximately, the humidity is constantly 50-55, this is only for birds, for example, chickens, guinea fowls, quails, which are not waterfowl (!)

[@liisarich7978]

@@jessemarvinvelarde8331 I do everything at a temperature of 37.7-37.8 approximately, the humidity is constantly 50-55, this is only for birds, for example, chickens, guinea fowls, quails, which are not waterfowl (!)

[@lynnyuenjudd6871]

I wish she would explain it better , I don't know how to get the eggs day set and how to get the humidity to were I want it , wish someone would help me please

[@TB-db1hv]

I brought one of these and read the instructions but can't get the hs setting lower then 30.0, does anyone know if I can get it lower as need to get it at 29c but mine will not go lower then 30c.

[@MegaPad3]

please i have this kind of incubator and my humidity is aroun 90 s

[@lallorona6014]

Omg 90% wtf

[@lallorona6014]

Open a vent or something.

[@lallorona6014]

What are you hatching Turtles

[@liisarich7978]

Add very little water. Right now, I add 1 teaspoon every 1.5 hours. This is the only way it works ..

[@kassadie6675]

How do i reset the egg day counter thing someone please help me understand

[@STFOURNARIS]

Just got one out of the egg today and and another 4 started so far so good although the thermostat is off by few degrees

[@jessemarvinvelarde8331]

Hello what temperature and humidity should be?

[@rachaelknight8048]

if its out a few degrees calibrate it with ca if its higher than it should be lower ca if its lower raise ca

[@liisarich7978]

@@jessemarvinvelarde8331 You don’t need to touch it, so you knock the settings, but you don’t adjust the humidity. So only the digit is regulated, which means when the signal will go. But you can't regulate the temperature itself. Just press briefly on the top button on the left and select the desired temperature with the keys up and down. Do not do anything with factory settings, where CA and other letters!

[@liisarich7978]

@@jessemarvinvelarde8331 I do everything at a temperature of 37.7-37.8 approximately, the humidity is constantly 50-55, this is only for birds, for example, chickens, guinea fowls, quails, which are not waterfowl (!)

[@nevenastankovic9044]

How to set the Days? i just bought it and display for Days says 7, how to set it to count days from 0 or 1? Thank you 😊

[@dannypritchett01]

Wondering too

[@kassadie6675]

Same bro

[@WakitaSantana]

​@@kassadie6675reset button and unhook the power cord in the face plate at the same time

[@mdrafiqulalam6932]

How much ...this incubator.

[@joenapoleone3850]

Can you show how to set the humidity and the temperature for the chicken eggs and the days setting I got the incubators but had trouble set the humidity what is the setting temperature should be on . Thank you

[@liisarich7978]

Add very little water. Right now, I add 1 teaspoon every 1.5 hours. This is the only way it works ..

[@liisarich7978]

You don’t need to touch it, so you knock the settings, but you don’t adjust the humidity. So only the digit is regulated, which means when the signal will go. But you can't regulate the temperature itself. Just press briefly on the top button on the left and select the desired temperature with the keys up and down. Do not do anything with factory settings, where CA and other letters!

[@liisarich7978]

I do everything at a temperature of 37.7-37.8 approximately, the humidity is constantly 50-55, this is only for birds, for example, chickens, guinea fowls, quails, which are not waterfowl (!)

[@AIAllar]

Would love it if you could add subtiles please. Not that your english is bad or anything, its just that the mic quality isnt the best and some words get lost along with the accent. English isnt my main language either so its hard to understand some of it.

[@AIAllar]

Like at 1:53 i hear "most important ...something-something... humidity... and i really get what is being said.

[@liisarich7978]

Add very little water. Right now, I add 1 teaspoon every 1.5 hours. This is the only way it works .. You do not need to touch this, so you knock the settings, but you do not adjust the humidity and temperature. So only the digit is regulated, which means when the signal will go. But you cannot regulate the temperature or humidity itself. But to set the temperature, just briefly press the upper button on the left and select the desired temperature with the up and down buttons. Do not do anything with factory settings, where CA and other letters! I do everything at a temperature of 37.7-37.8 approximately, the humidity is constantly 50-55, this is only for birds, for example, chickens, guinea fowls, quails, which are not waterfowl (!)

[@onetwo6614]

my incubator runs about 37. humidity is way up I live in north carolina how much water do I need to add to get correct humidity? help! I placed eggs in about 24 days ago and none have hatched..

[@TheLAShop]

Hi! The temp and humidity may be affected depending on the environment as well. Is the incubator set at an average room temp? anywhere between 68-74 degrees?

[@freddiervz2158]

They are dead 💀. You can check your 🥚 with a good flashlight after six days you can see the veins inside the shell.

[@amedeuskiwango8285]

The LA Shop i have this kind machine im not sure if its work perfectly course the temperature is between 37.8 - 38.4. can i succesifully if i put the eggs? And the humidity is between 70 t0 72

[@amedeuskiwango8285]

The LA Shop The LA Shop i have this kind machine im not sure if its work perfectly course the temperature is between 37.8 - 38.4. can i succesifully if i put the eggs? And the humidity is between 70 t0 72

[@hamdajontursunov1515]

где покупаете инкубатор мини

[@renealopez3960]

How do we adjust the Humidity. I see this question being asked over and over with no answer. Just set up system and Humidity it super high.

[@liisarich7978]

Add very little water. Right now, I add 1 teaspoon every 1.5 hours. This is the only way it works .. You do not need to touch this, so you knock the settings, but you do not adjust the humidity and temperature. So only the digit is regulated, which means when the signal will go. But you cannot regulate the temperature or humidity itself. But to set the temperature, just briefly press the upper button on the left and select the desired temperature with the up and down buttons. Do not do anything with factory settings, where CA and other letters!

[@saihjameh3258]

How much?

[@chriscasey4525]

i managed to hatch one set of eggs,but cant get the temp to 37/5 now,any ideas whats the matter,its only 2 months old

[@DirkVoortmans]

I had the same issue with the older model, I ordered a new heater and replaced it... Google this: 80W Incubator heating

[@RestorationAcresTN]

@@DirkVoortmans thanks for this!

[@ammritpdl9384]

My humidity sensor doesn't work how to repair

[@appuselvi2809]

How to fetch the water in this incubator.please tell me.thank you

[@liisarich7978]

Add very little water. Right now, I add 1 teaspoon every 1.5 hours. This is the only way it works ..

[@bossbre23]

I cannot get my humidity to set to 50 what did I need to do?

[@TheLAShop]

Hi ! What is the temperature being set to? Send us a message to [e-mail]

[@liisarich7978]

You don’t need to touch it, so you knock the settings, but you don’t adjust the humidity. So only the digit is regulated, which means when the signal will go. But you can't regulate the temperature itself. Just press briefly on the top button on the left and select the desired temperature with the keys up and down. Do not do anything with factory settings, where CA and other letters! Add very little water. Right now, I add 1 teaspoon every 1.5 hours. This is the only way it works ..

[@ismaelmadrigal]

Do you have to turn eggs every 2 hours?

[@lallorona6014]

No 2 times a day but not on the last 3 days stop turning them at this point in stage of time they are positioned to hatch.

[@rodalyngale4328]

same here I watched videos about turning time and it says 4-6x a day,but this incubator has 2hrs interval..can it affect the egg?

[@eveyohanah9540]

What are the factory settings supposed to be? I think I may have messed with them when I shouldn't have. What do the symbols mean for setting temperature and humidity etc? Thanks

[@sas_grimreaper4987]

My incubator beeps even when it has 55 humidity and 37.5 temperature... same incubator as yours here.. pls help

[@TheLAShop]

Can you confirm if it is the humidity or temperature that is flashing when it starts to beep?

[@sas_grimreaper4987]

Thanks La but u reply very late ... now I know it was the humidity

[@TheLAShop]

@@sas_grimreaper4987 We sincerely apologize for the delay response. You may contact us directly via email if you have any other questions at [e-mail]

[@احمدالعاني-د7ه]

The EE symbol for egg tray, 32 eggs, appears

[@nancygiron1804]

How do I set my temperature to 37.5 and humidity to 60

[@liisarich7978]

Add very little water. Right now, I add 1 teaspoon every 1.5 hours. This is the only way it works ..

[@mariadelourdesgakiyairiart7790]

Is there another video, showing the next steps to take? Thanks

[@TheLAShop]

Hello! Unfortunately, we do not have a continuation to this video as of yet. However, if you do have nay questions, please feel free to ask and we will do our best to help you!

[@chriscorcoran6983]

How do you set the counter for the days

[@JoseReyes-iw4bk]

Is the incubator supposed to stay in the foam case it comes in?

[@lallorona6014]

@@chriscorcoran6983 why not just use the calendar chicks hatch in 21 days.

[@jacquelinenelson23]

@@TheLAShop how do i the beeping noise in the machine

[@poncianoramirez8092]

How much water u out in im trayin to get the humidty hight at 45 but im havin trouble

[@tonmoyphukan]

Nandagopan Jeyasundra - my temperature in the display is defective it used to go up to 38 in 10 mins. But now it is not going beyond 33.6 / 33.8. My 38 eggs got wasted recently.

[@liisarich7978]

Add very little water. Right now, I add 1 teaspoon every 1.5 hours. This is the only way it works ..

[@liisarich7978]

@@tonmoyphukan You do not need to touch this, so you knock the settings, but you do not adjust the humidity and temperature. So only the digit is regulated, which means when the signal will go. But you cannot regulate the temperature or humidity itself. But to set the temperature, just briefly press the upper button on the left and select the desired temperature with the up and down buttons. Do not do anything with factory settings, where CA and other letters!

[@68zidane]

Can you please tell me how to reset day counting on this incubator? Thank you

[@thecakeladytm9962]

Hold down the red/green arrow button.

[@benbean1940]

There is no red or Green arrow, please explain

[@kassadie6675]

​@@thecakeladytm9962 thank you soo much

[@jaimemadrid7236]

How much

[@hal3837]

My incubator is overheating.what's wrong? I setup the machine to 37.7c but continue to increase until reach 41.5 and not comes down.....please help me ...thanks

[@TheLAShop]

Hello! Please make sure that there is enough water to humidify and control the temp.

[@liisarich7978]

You do not need to touch this, so you knock the settings, but you do not adjust the humidity and temperature. So only the digit is regulated, which means when the signal will go. But you cannot regulate the temperature or humidity itself. But to set the temperature, just briefly press the upper button on the left and select the desired temperature with the up and down buttons. Do not do anything with factory settings, where CA and other letters!

[@ognjenmrakovic5348]

Can you send me parameters for FA HS LS CA Thank you

[@ognjenmrakovic5348]

I touched earlier HS and FA and i need original parameters

[@TheLAShop]

@@ognjenmrakovic5348 HS: 39.5°C (103.1°F), LS: 30°C (86°F), CA: 0°C (32°F)

[@mandelman4518]

This is crap, I have one of it and I never had good results, from 48 good eggs you can get 15 chicks if you are lucky. I have to investigate, but I believe that the temperature on the sides is lower than in the middle

[@AIAllar]

Well are you sure all the eggs were fertile? You dont get chicks from every egg unless you are 100% sure the rooster has mated with all the chickens before the egg was laid.... if any eggs hatch, that means the machine worked just fine. Just means the rest of the eggs werent fertile.

[@mandelman4518]

@@AIAllar only 5 eggs of 48 wasn't fertile, the rest had dead chicks inside. I think that the temperature in the center is OK but a bit colder on the sides. I have only 13 chicks but I'm happy. At this time I have another 48 eggs in it but this time I insulated the bottom and sides. I wish I can upload a video to show you

[@smokey_4206]

@@mandelman4518 it iss this is a crapp incubator i had best results with my janoel 12 bestt incubator for good results i had bought shipped eggs off ebay and 6 hatched out of 12 so 50%hatched i was pretty suprised for shipped eggs but thiss here noo the eggs on the side feel colder but the middle kinda warmm

[@redsaens2823]

I actually am now starting off on this. Was given this incubator to run some trail 'common' flow eggs. Fortunately, I placed my eggs in the center. Not sure what made me do it but thankfully your comment gave me some minor motivation.

[@taylorkeate2297]

How do I tell if my egg turner is working?

[@TheLAShop]

Hi Taylor, please watch at 3:50 min into the video to confirm if the settings is done correctly.

[@taylorkeate2297]

The LA Shop is there a way I could of connected the wires wrong because it’s brand new

[@reksmeyok1957]

I have this Chinese incubator with two layers. The problem is humidity level is between 73 and 75. I lost a lot of bird babies cos they couldn’t come out of the egg shell which I guess was because of too much humidity level. It should be lower than 60%. Anyone help me please to set the humidity level. I followed the user Guide instructions but I didn’t work. Thank in advance.

[@fishmut]

Reksmey Ok so from researching I have done is low humidity around 50 to 60 % and in the final stages of incubating day 18 and on till hatching around 70 to 80% this helps soften the egg shell for the chics to break out of there shells. Best to do your own homework my info is only a guide probably not correct but giving you an idea to give you some help I hope.

[@renealopez3960]

Did you ever get any help with your Humidity???? I just got mine and I am having the same problem.. Please help..

[@Serkanylmaz_61]

@@renealopez3960 hello first I did this machine I first gave a space with the paper of the machine by the uct and the humidity 55 I found 37.7 at this temperature I have set this exact solution machine normally 38.2 temperature with this negative second if the moisture content of a bolumude full of 65 I find what I do This is because the air wave from the top of this machine cannot be fully removed and there will be no problem.

[@liisarich7978]

Add very little water. Right now, I add 1 teaspoon every 1.5 hours. This is the only way it works .. You do not need to touch this, so you knock the settings, but you do not adjust the humidity and temperature. So only the digit is regulated, which means when the signal will go. But you cannot regulate the temperature or humidity itself. But to set the temperature, just briefly press the upper button on the left and select the desired temperature with the up and down buttons. Do not do anything with factory settings, where CA and other letters! I do everything at a temperature of 37.7-37.8 approximately, the humidity is constantly 50-55, this is only for birds, for example, chickens, guinea fowls, quails, which are not waterfowl (!)

[@liisarich7978]

@@renealopez3960 Add very little water. Right now, I add 1 teaspoon every 1.5 hours. This is the only way it works .. You do not need to touch this, so you knock the settings, but you do not adjust the humidity and temperature. So only the digit is regulated, which means when the signal will go. But you cannot regulate the temperature or humidity itself. But to set the temperature, just briefly press the upper button on the left and select the desired temperature with the up and down buttons. Do not do anything with factory settings, where CA and other letters! I do everything at a temperature of 37.7-37.8 approximately, the humidity is constantly 50-55, this is only for birds, for example, chickens, guinea fowls, quails, which are not waterfowl (!)

[@hasan4599]

اكو عراقيين فشلتونه 😂😂😂😂 حسيت نفسي غريب 😂😂😂💔🙂🌝🤬

[@ahmedalmamgir6191]

how mach

[@Saul5.7]

I haven't had any luck with it no hatch @ all the humidity is @ 65 70 temperature is @38.1 i dont know why

[@liisarich7978]

Add very little water. Right now, I add 1 teaspoon every 1.5 hours. This is the only way it works ..

[@umarmukthar7957]

How much price this ?

[@amubai3688]

Good.

[@emerictassel9064]

Awesome

[@vynkanehkova7533]

Интересувам се как се включва за работа ,как се работи с него имам го но не мога да го пусна благодаря предварително ако може някой да ми помогне

[@preciouslife7862]

It's helpful

[@rachaelknight8048]

the ontroll panel is fantastic the container is crap more fluctuation than my boyfriends underpants

[@Beckysgetsittogether]

Did you use the styrofoam to keep the heat in?

[@rachaelknight8048]

@@Beckysgetsittogether yes luv i had to or the hatch rate was so poor

[@Beckysgetsittogether]

@@rachaelknight8048 The manufacturer recommends using the styrofoam.

[@rachaelknight8048]

@@Beckysgetsittogether yea your hatch rate would be pants without the foam

[@okoidigunpeter9636]

Any one that takes one thousand

[@treksandpreps]

Rat rideo ras ro rad

[@vincenzolaveglia144]

Se per favore e' possibile sapere come si imposta la temperatura. Che ha a me non mi supera 35.1 Gradi.Sono disperato. Un video in Italiano? Ho istruzioni in Italiano. Grazie per chi aiutera' Vincenzo cell. 3337731200

[@liisarich7978]

Add very little water. Right now, I add 1 teaspoon every 1.5 hours. This is the only way it works .. You do not need to touch this, so you knock the settings, but you do not adjust the humidity and temperature. So only the digit is regulated, which means when the signal will go. But you cannot regulate the temperature or humidity itself. But to set the temperature, just briefly press the upper button on the left and select the desired temperature with the up and down buttons. Do not do anything with factory settings, where CA and other letters! I do everything at a temperature of 37.7-37.8 approximately, the humidity is constantly 50-55, this is only for birds, for example, chickens, guinea fowls, quails, which are not waterfowl (!)

[@sulthansulthan8500]

هي

[@karenfortier2188]

I recommend adding English subtitles, please.

[@paulcat8816]

too bad it was not made for americans

[@amymccain-davis8362]

How do I turn off the humidity alarms?

[@JuanMendoza-cr4bo]

Following. I just bought one and it doesn't persure after the first 2 minute

[@koushikbiswas4301]

Highest temperature and humidity setting how?

[@koushikbiswas4301]

Highest temperature setting

[@okelloraymond2115]

can this incubator work for turkeys as well

[@lallorona6014]

Try sports man incubator for turkey eggs.

[@trumptrump4543]

How do I adjust humity ? Help

[@vanishvanish2122]

Yes

[@vanishvanish2122]

Hello

[@tmueller333]

How do you reset the day counter?