How to use HCW-M635 low voltage disconnect battery protection module tutorial.

[@cuker1935]

The BEST tutorial I came a cross jet. 10 out of 10

[@naseebramlakhan3906]

Thanks you bro, i was searching for over 45 Min to make this work before i found your vidéo. Great vidéo!

[@avebello2603]

Confused ako sa setup ng LVD. Pero nong mapanoodko itong video mo, na setup ko narin. Tyvm sa tutorial mo!

[@sureshdefonseka2394]

Perfect explanation when compared to other clips. Simple and sweet valuable video clip, thank you.

[@Electronzap]

Nice tutorial.

[@moturcu4226]

You are legend mate.

[@adamsisernik4556]

I have two LifePo4 batteries, Basen Green 11.7kWh 51.2V (BG), and Ecoflow Delta pro - inverter 48V 3.6kWh (DP). I use BG to charge a DP battery via XT60 solar input (400W 8A). With the DP application, it is not possible to set the BG not to be completely discharged? Would be such adjustable 48V DC Over and Under Voltage Monitoring Protection Relay suitable for my batteries, so that voltage limit (under 51V) will stop charging DP from BG battery?

[@RustyCandyAdventures]

Tip. You might need to press the button 3 times, once on the other then back. Quickly. To reset press both buttons.

[@renzmarionamio7908]

Thanks for the tip.

[@964czarlee]

I dont get it.. how do you do that?

[@RustyCandyAdventures]

As per this video. When you get your circuit. Reset the settings by pushing both buttons, 888 will flash.

[@RustyCandyAdventures]

Then measure you supply voltage. To set this value into circuit. Press the left button. You need the numbers to flash. You might need to press 3 times left button once right then again left. Keep going until number flash. Set your value.

[@RustyCandyAdventures]

Now set your drop out voltage. This time you have to get the decimal place led to flash. Same again 3 times left, once right button. Until the decimal place flashes. Set your value.

[@hermanpakpahan7476]

Thankyou so much ...

[@ahlexc7866]

Happy New Year! Thank you sir sa tutorial, showing us how to set it, hanggang ilang amperes po ang kaya niya

[@renzmarionamio7908]

rated as 20A 14v yung relay nya po. kaso liit nya di ako bilib na kakayanin nya yung upto 20amps po cguro para safe mga around 5amps lang po.

[@MrPahan11]

What is the maximum power this board can withstand? After half an hour / load of 50 watts, it has already warmed up a little

[@anissbenthami]

music is annoying

[@livingabestlife8]

This video would be perfect for me if you show how you connect to the inverter. I see the operation on the module, but the 2 wires coming out from the battery how and where did you get them? a basic question for many but for me that is something I need to see. Thanks for your time.

[@djmillerscountryshack1049]

I think that rather than a Music Video....perhaps you give a vocal tutorial on the product. Just our opinion.

[@DjAMPEROK]

How connected power supply (charge) ? In or out?

[@3maisons]

I prefer tutorials that talk, not bleat.

[@MuhdHanif-cg3zm]

❤❤❤

[@kasunperera4625]

How much ampier this can handle? Can we set cut off value higher than on?(to use as chaging cut off module)

[@renzmarionamio7908]

For safety you can use it 10A below. No you can't set the cut off higher than the reconnection voltage. It is intended only to protect the battery from over discharge.

[@otnakinamu7503]

boss! anu po ba dpat una? breaker to lvd or lvd to breaker?

[@MuhammadArsalan-qp2jg]

I installed the same module with my china inverter i set my cutoff voltage to 11.3v so on load usually voltage drops so this module turn off my inverter once the inverter is off again my voltage increase then again this module turn on my inverter and it is working like loop ,, Could you please help to sol my problem ?

[@BernalXenia-c6v]

Estevan Viaduct

[@rdgamingtv0816]

Sir Anu po dapat lvd ng lead acid 12v 65ah

[@stephanpieterse6960]

Your left and right is wrong way around ----> Left🤲Right

[@franklinballesteros8894]

Alam nyo walang silbi yang LVD na Yan. Ipapakita mo be mag adjust madali lang pero anoba talaga gamit Nyan?

[@moturcu4226]

My one after disconnect not reconnect again.

[@elloydnaberdas5794]

Hindi na umilaw, wala na rin output. Ano ang sira?

[@brunomarch-ym1zk]

Bakit dika nag sasalita