How To Use NE555 For Inverter 12V To 220V 400W

IC NE555 is a very common and popular type of IC, present in many applications such as LEDs, pulse generators, logic clocks... The NE555 IC itself only generates single pulses, in this video I will combine it with an NPN transistor. To make a 12V to 220V inverter in a push pull configuration. This inverter circuit works stably with output pulse voltage to drive mosfet above 5V.
----------------------------------------------------------
Schematic please download at here
drive.google.c...

[@oilbay54]

Duty cyle is around 0.49. That means Q1 and Q2 conduct unevenly. This heats up the core. Secondly the transistors don't have any protection diode. Therefore the inductive kickback when it is cut off will destroy it. In the comments you read those complaints about "pap up". Thirdly, never use this inverter for a delicate instrument. Do not check the secondary voltage with an oscilloscope. You'll have a burnt scope.

[@VEERsciencePROJECT]

Ham bhie bana rahe same isi type ka charging k saath

[@taikong7952]

Thank you, the clip is clear, the diagram is complete

[@VEERsciencePROJECT]

Very good making keep it up brother

[@Dc_tech386]

No no this design don’t work trust not everything you the c1815 npn transistor won’t work because if the npn can’t spike the current the two mosfet will turn on as ones the right way to do it is use s8550 pnp and remove the 2k resistor to base and ground connect emitter to positive and collect to the mosfets gate each high signal turn off the low side and each off time of high side the negative signal turn on the low side mosfets that’s the the way it’s done

[@UpinkProduction]

I love it good Keep uploading videos like this

[@DIY_Electron]

Thank you for watching

[@danielchatrie6614]

I try this circuit only one mosfet fully on the ic can't power the other side my mosfet burn out because of that

[@nux_asr]

if I use another mosfet is there anything that needs to be changed

[@qxd666]

if i want to use 13007 transistor instead of mosfet, what is the circuits?

[@lakshminarayanasomayajula3295]

You would have connected another 200W lamp and shown the battery voltage (12V) and output voltage (230V) It is a distorted square wave output.

[@hsb.variedades]

Manda esquema pa mim

[@sayeedbaig7618]

Can v use P80nf55 MOSFET by this same components in this same way.

[@SK-is8kl]

👍👍👍👍👍

[@kaunghtetzaw341]

irf44 use?

[@DIY_Electron]

Ok you. Usable N channel mosfet

[@danielchatrie6614]

I don't get why the gate voltage is 51volt what happening here

[@danieledeboni8934]

It's its frequency

[@polatmexmetoglu3175]

Xelo

[@pratapsonar7952]

Kya bnaya be

[@full954]

Нет даттайма полёвки такого не любят.

[@kamalhusein6688]

Can run fan or tv plz plz plz quick reply

[@ahmarrana9732]

Nice job

[@lakshminarayanasomayajula3295]

It is distorted square wave and you would have added another 200W bulb and shown the battery voltage 12V and output voltage 230V with load.

[@DIY_Electron]

It is not yet complete to run inductive load device. The battery 12V does not have much voltage drop. Only the 220V output suffers a lot of voltage drop, because the transformer has a small secondary winding. I need to upgrade the transformer to ensure capacity. Hope you continue to give your comments, so that I can do better in the next videos.

[@lakshminarayanasomayajula3295]

The voltage depends on number of turns only. You have to reduce the the SWG of the wire with the same no. of turns which increases the size of the core. The square wave increases the loses in the core. High quality iron core is to be used. The Ah of battery is to be increased to handle higher power like 400W or more. This inverter cannot be used for costly TV’s.

[@DIY_Electron]

Thanh you

[@sergeypetrov1358]

400ват не будет

[@vittalkoppal]

Can we use D718 with it 🤔

[@minhnhat-qz3hy]

Tôi muốn thay đổi tần số 36Khz để chạy biến áp xung thì thay đổi linh kiện nào trong mạch điện để đc mức tần số đó vậy anh bạn

[@ungdungkhoahoc]

Bạn chỉ cần thay tụ 104 xuống tụ 222 là được , chào bạn

[@NoypiCraft20]

Nice work

[@carpenterl45hamza]

👍👍👍👍👍👍👍

[@sahulhameed4437]

Super👌👌👌👌👌👌👌👌👌

[@franciscogomes8446]

Repostas

[@mastertech9235]

Hey foool.... Transformer is main parts bt uu did not share that details

[@magaiver5640]

ta doido da mais trabalho do q mexer com SG 3535

[@kazakimotorshouse3275]

Canot get 400w Fake

[@atikuaticulated5757]

what components can i add to the circuit to give power output of 1000w?

[@radargenta]

the MOSFETs and Transformer must be compatible with power

[@k4728X6]

Transformer rating/model

[@k4728X6]

Please mention it

[@evgeniylazurenko]

Please scheme?!

[@DIY_Electron]

Diagram in the video description. Thank You

[@evgeniylazurenko]

@@DIY_Electron Thank you very much!

[@minhnhat-qz3hy]

I want to change the frequency of 36Khz to run a pulse transformer, what components should I change in the circuit to get that frequency, my friend?

[@DIY_Electron]

Because it is also related to the duty cycle, you have to change the value of R1 with a 100 ohm resistor (R1 connects between pin 7 and pin 4, 8). R2 is replaced by a 20K resistor, you can use R10K in series with a rheostat to adjust the frequency accordingly. Next replace the 100nF capacitor with 1nF. Good luck

[@ChavMusic]

Good job!