How to use potentiommeter as Volume

[@Proud2bTucsonNative]

Thank you. Exactly the information I needed.

[@piuskaraba6134]

Thanks, Best representation so far i love it

[@Dryuckey]

I need to make one for a 1/4 speaker jack to control the one monitor speaker volume running off the main speakers?

[@stagehand9002]

Thats exactly what i need to do - bridge my 200w bi-amp to 400. run a 1/4 cable off the main speaker to a monitor speaker but be able to control the monitor volume - did u have any luck?

[@coondogtheman]

Will this work on the speaker output from a small amp to a speaker? I have this bazooka tube bluetooth speaker and it's mono and when I turn it on and put the radio on it blasts full volume. Can I add a volume potentiometer between the amp board and the speaker to control the volume so it doesn't blast my ears out and then turn it up to the level I want? There are just two wires going to the speaker, positive and negative.

[@coolmonkey5269]

did u do it i hav same problem

[@coondogtheman]

@@coolmonkey5269 No, need to find correct potentiometer.

[@hassanrguiti9686]

Nayda khoya

[@vermagaytriben3064]

Can i joint Bluetooth adapter with it

[@klebersilva5318]

Muito Legal Brother !!! Vou fazer aqui em casa Simples e objetivo....Obrigado!!!

[@jadilson_paiva]

Thanks!!! Did the potentiometer adjustment make the volume linear? I'm thinking of doing this to control the volume of a preamp output.

[@SharvilSawargaonkar]

Yes it is linear and can old used pream

[@reshamondal5654]

Is potensiomitar kitnaka ha

[@veghbela]

thanks! I was looking for exactly this.

[@aronndou7924]

Hi mate plz explain to me probably I have the equipment jus a beginner an don't want to blow up the house

[@veghbela]

just follow the video, make sure do not short anything , but you can not do mush problem, there is no high voltage in this obviously@@aronndou7924

[@gsp2157]

Thanks for the clear presentation...

[@cristianleonelleolp9138]

Que tal te go una pregunta ? Por ejemplo en un equipo de sonido puedo bajarle el volumen poniendo un potenciometro a una sola bocina y la otra si que venga directa del equipo y solo poniéndole por a una

[@ramprasadkodam4533]

Very nice i thankful to you

[@ishaandobhal6397]

Can I drive Earphones thru this?

[@mmustafa5020]

Yes

[@hklrzrazali7001]

Does it get louder than phone volume control?

[@thetechdoggy]

no

[@chainenaimslama1870]

hello please can you help me to change sound volume using potentiometer and microbit and microbit speaker or an external speaker thx in advance best regards

[@gilperon]

You should use a 1k type A potentiometer, it would produce much much better results and the volume control would be smoother because type A are logarithmic. Also, 10k is too much as you did in your video, I would recommend 1k.

[@owenthepug]

There's also already a volume nobe on it

[@traceyhersha]

I'm trying to make mine a bass control knob for my subwoofers do I hook it up the same way as it showing on the video

[@benedictusmaladaptus2712]

Hi Gil. I want to add a pot to my speakers to only control the tweeters (they are way too much). What do you recommend, and why? Thanks in advance!

[@EMCproductionfan]

@@benedictusmaladaptus2712 just put a diode

[@AGoodBuzz]

@@EMCproductionfan Thanks, but, but isn't that a fixed-level attenuation? I came across some things called L-pad attenuators that claim to adjust volume without changing the resistance, however I installed some from Parts Express per the instructions but they don't do anything noticeable. The ideal solution would be the ability to go from full output down to zero output at my discretion..... Thoughts?

[@kalilanda1088]

Genial 🤘 gracias

[@longpapa4442]

👍👍

[@JHON72254]

Muy bueno gracias por el aporte amigo saludos

[@ritaisabel8665]

Good

[@KailashKumar-ok8pr]

Very nice

[@vinayacharya6916]

Super

[@bluepen215]

Thanks

[@bluepen215]

Good a g

[@gopiramsonkar1454]

Good night

[@CreativeAndDuck]

You too :D

[@ishantakki]

Thank u so much

[@VolumetricTerrain-hz7civ]

Allow me to introduce a new unit of measurement for sound volume, which I call vovol* (abbreviated: volume voltage). THIS IS HOW IT WORKS: You use two pre-stages, one with positive volume values, and the other negative. For example, so has the pre-step with positive values a measurement from +0 decibels up to +20, while the one with negative values, has from -0 decibels down to -20 decibels. The highest voltage occurs when the value is +20 and -20 decibels (or: 20 vovol), while there is low voltage, when the value is on +0 and -0 decibels (or: 0 vovol). You can possibly also combine two different values with each other, by adjusting the value to +10 -20 vovol, which gives a crisper effect. Have experimented with this myself at work and at home. The adjustment can of course be set to taste, but the purpose of vovol for me is to equalize the sound volume, so that you better hear weak sounds and at the same time avoid high deafening sound levels (loudness war's). Thank you for reading this! Take care of your hearing... :-)

[@lethimaile8355]

Like

[@hamzamalik221]

I WILL MAKE THIS

[@flat-earther]

did you do it yet?

[@juarezcastelo]

OR... OR.. just hear me out man, OR you could use the phones volume control!!

[@lethimaile8355]

See the top

[@bluepen215]

Thanks