How to use : Wireless Remote Control Switch AC 250V 110V 220V 2CH Receiver and RF Remote Controls

433Mhz Universal Wireless Remote Control Switch AC 85 V ~ 250 V 110 V 220 V 2 CH Relay Receiver Module and RF 433 Mhz Remote Controls
#QIACHIP #KR2202
From:
www.aliexpress...
Link from DE: www.amazon.de/...
About Working mode:
Momentary:Push the remote button , the relay connects, release the remote button , the relay dis-connects.
Toggle:Push once the remote button , the relay connects , push twice the remote button , the relay dis-connects .
Clearing the code :
Push the learning button on the receivers for 8 times , the codes will be cleaned .
After clearning the code, all the remote control cannot work any more.
Learning the code :(momentary)
Push the learning key on the receiver once time , it comes into momentary setting mode .
Wait for a moment , the LED will be off , it comes into learning state .
Push the remote button , LED indicator on the receiver board will flash then come off .
After 3 seconds, the LED indicator will be on again , learning successfully .
Learning the code : ( Toggle )
Push the learning key on the receiver twice time , it comes into toggle setting mode
Wait for a moment , the LED will be off , it comes into learning state .
Push the remote button,LED indicator on the receiver board will flash then come off.
After 3 seconds , the LED indicator will be on again , learning successfully .

[@abishaicampbell2187]

How did you wire this?

[@qiachip]

I'm glad to see your question. Many people have the same question as you. So I made a long video to explain the working principle in detail using motor control as a demonstration. Link: kzbin.info/www/bejne/pWi2k4d4dsp0orc This should answer your questions. If you still don't understand, you can ask further questions. I hope it can help you.

[@464340]

Thanks for the demo, I've used this module to lock and unlock my car.

[@thechecksix7295]

Obviously some commenting people cannot read and/or watch and think. At least I am very happy and thankful for this video. Great and helpful.

[@qiachip]

Nice to hear that, thank you so much!

[@Adrenalina377]

Obrigado pela demostração. Saudações Brasil ✨

[@TheRafal135]

You save me a lot of time 😅

[@sergiomonteiro3314]

Hello, it's possible to use 1 channel in momentary mode and the other in toggle mode? Or both channels will work always in same mode?

[@MuhdZikrii-w3t]

Can I get the schematic diagram and PCB layout of this kit KR2202 ?

[@itzvillager5757]

Bhai light jaatne pr jb relay ki power off hogi TB kya remote ko fer s connect Krna padega

[@qiachip]

Thank you for asking a question that many people want to ask! Answer: No need to re-pair or reconnect! If your receiver loses power, it will still remember the remote control. After it is powered on again, you can still use the remote control to control it; Only when you perform code clearing settings, the remote control needs to be re-paired Hope this can solve your doubts Best wishes

[@___r0w]

The clearing code was useful. Thank you so much

[@enzoingrosso26]

Bravissimo !!!GRAZIE !!!🤗

[@sadiqshaikh1876]

can i use single remote for 1 switch as momentary other one toggle mode

[@qiachip]

I'm glad you asked this question. Let me understand what you mean. You have two switches and one remote control. Then the remote control is used to control the two switches, and they use different modes, right? In theory, it is possible, but it is not recommended. Unless your switches are far away, because you have to consider that when you turn on one of the switches, the signal of the remote control may also be received by the other switch. So it's better to use two remote controls to avoid interference. I hope you can solve your doubts and look forward to follow-up feedback!

[@abdevilliers8906]

can we use this for 12v battery? and with car remote also ?

[@qiachip]

Yes,your think is perfect

[@zubairsami5668]

How can your remote (transmitter)work automatically?? Means automatic submersible pump motor on/off functional.

[@qiachip]

I'm glad to see your question. Many people have the same question as you. So I made a long video to explain the working principle in detail using motor control as a demonstration. Link: kzbin.info/www/bejne/pWi2k4d4dsp0orc This should answer your questions. If you still don't understand, you can ask further questions. I hope it can help you.

[@youbless4630]

Hi I would try this product on my motorcycle can we setting: Button A as Momentary: Push the remote button, the relay connects, release the remote button, the relay dis-connects ? Button B as Toggle: Push once the remote button, the relay connects, push twice the remote button, the relay dis-connects ? Thanks and I appreciate your help.

[@scottiboy99]

Can you program 2 channels on one button

[@teeratornpharnusopon750]

@ toggle​ mode, Can​ we set​ one​ Channel​ will​ work​ at​ a​ time( can't​ 2​ Channel​ at​ the​ same​ time)​

[@qiachip]

let me see it is supported You can watch a demonstration in our latest video kzbin.info/www/bejne/e4LcfJqah9-Nhac If you still have any questions, feedback is welcome

[@GSTomsk]

Два (или больше) передатчика могут одновременно быть запрограммированы на разные режимы. Например на одном кнопка осуществляет активацию канала пока нажата, на другом пульте при первом нажатии вкл, при втором - выкл. Но можно также запрограммировать разные режимы для каждой кнопки на ОДНОМ пульте.. Например "А" будет активировать канал "А" пока удерживаешь кнопку, а кнопка "В" будет при первом коротком нажатии включать канал "В", при повторном выключать. (пробовал на своём модуле). Также можно запрограмировать например включение канала "А" только при нажатии одновременно обоих кнопок (своеобразная защита включения от случайного нажатия какого либо "серьёзного" устройства). При этом при удержании кнопки "А", будет включен (пока нажата кнопка) канал "В", а при коротком нажатии кнопки "В" канал "В" сначала вкл, при повторном нажатии ВЫКЛ. При включении канала "А" (одновременно жмём 2 кнопки), выключение этого канала кнопкой "В". Дерзайте!)))

[@katjaczajkov8694]

hello, u press on first remote control, until u release the button, the relay reset at self. how u have configured it? i have same plate, and if i press button relay go on, and seconed press same button, realay goes off.

[@marioscanu64]

Good morning, I have purchased the material for a hoist to make it work in wireless mode. If you can help me to connect the wires, make me a diagram, putting the colors of the wires of my hoist and connect it to the control unit or box. Thanks, I ask for your help.

[@qiachip]

Hello, thank you for your trust and questions. Let us know that there are many requirements for lifts. We have produced a series of motor wiring and operation videos for this. We believe that you can solve your problem after watching this video. How to use 2CH RF remote switch linear actuator controller forward reverse rotation momentary KR2202 kzbin.info/www/bejne/e4LcfJqah9-Nhac If you still have any questions, you can take a photo of your control box and wires and send it to our email. We will answer your specific questions. I hope to solve your problem and look forward to follow-up feedback.

[@marioscanu64]

good morning, if you send me an email I will send you the photos, thank you very much for your interest.

[@marioscanu64]

good morning, can you send me an email so I can send you the photos, thanks for your availabilit

[@qiachip]

[e-mail]

[@qiachip]

Looking forward to your photos and solving your problems

[@antoniomteruel]

Thanks for the video. I have a doubt. In the event that the electronic board does not receive electrical current (electricity cut), do you have to reprogram the remote control? or does it still work with the last programming? Thank you very much. Greetings.

[@MoesKeckeEcke]

Usually these keep their code and the remotes they work with it he power was away. What's more problematic is their default sometimes is on so if power comes back they will run your heater and burn your house down :-9 Or if the battery is flat the remote needs to be reprogrammed if the code is rolling, as the remote starts from zero code and the receiver wants some higher already rolled code and it mismatches so won't fire until learnt again. Every battery change => learn new remote in :-/

[@2gunslefty]

Can it be used for dc just to turn on a led light inside side by side . When dark

[@joeKisonue]

Yes, if the 12v kit is used

[@angeldelgado3411]

Good evening I would like if you can show the way in which the cables are connected to be able to carry out that work that I think is very good thanks

[@qiachip]

The video on how to connect will be uploaded later, so stay tuned! You can also provide your email, I will send you the wiring diagram and instructions of the product first

[@MashRain]

you mentioned how to use Wireless Remote Control Switch AC 250V 110V 220V, my question is can you really use that in AC with voltage 110 to 250 volts, that is for only 12 volts and how can the high voltage electricity run smoothly there while it's only 12 volts.

[@qiachip]

First of all, I would like to recommend two videos to help you better understand this product; How to use 2CH RF remote switch linear actuator controller forward reverse rotation momentary KR2402 kzbin.info/www/bejne/pWi2k4d4dsp0orc How to use 2CH RF remote switch linear actuator controller forward reverse rotation momentary KR2202 kzbin.info/www/bejne/e4LcfJqah9-Nhac One is 12 volts and the other is 220 volts Next, I will explain to you the principle in the video. There is also a 12-volt power supply connected to the small light in the video, which is not shown. The 220-volt power supply in the video powers the receiver to make it work. The receiver controls the relay to turn on and off, but does not turn on the 220-volt point to the small light Finally I hope I can answer your question. If you have any questions, you can ask questions and I will reply you quickly

[@waseemhassan2832]

Can we use it to start and stop electricity generator?

[@qiachip]

Theoretically it is possible. But you need to know how to wire it.

[@rushdHBTS]

Only for LED ? For Pump motor switching any necessary changes in design. Any commercial Plan ?

[@qiachip]

Not only for LEDs, it's just a demo. You can apply to other devices.

[@brunom5333]

Merci pour votre video c'est Super 👍👍👍😀😀

[@andreaschristodoulou4274]

why must be used TWO remotes instead of one ?? For example button A for relay one (CH,1) and button B for relay 2( CH2)

[@АлексейРащупкин-ф7э]

Спасибо! Хороший человек!

[@shanealam3764]

Hello Sir sahi kante ko kharab kese kar sakte hai baton se

[@Adriano70911]

How much power it takes? Is it not too much for ecooter?

[@qiachip]

Hello, I don't know what an ecooter is. But I checked it out. The answer given online is an electric scooter. If it is, then I recommend you to watch this newly made video. kzbin.info/www/bejne/pWi2k4d4dsp0orc How to use 2CH RF remote switch linear actuator controller forward reverse rotation momentary KR2402 You need to distinguish whether the voltage provided by the device you are using is consistent with the voltage of our receiver. I hope it can help you and look forward to your follow-up feedback.

[@Adriano70911]

@@qiachip Im sorry I meant an escooter. What's the power consumption of the remote as escooters battery is very limited

[@SportMaster666]

Подскажите пожалуйста где найти пульт на 220 вольт в котором имеется один канал но только с независимым контактом . ТОИСТЬ что бы с помощью пульта была возможность соединить разрыв независимой цепи.Please tell me where find a 220 volt remote control in which there is one channel but only with an independent contact. MEET that with the help of the remote control it was possible to connect the break of an independent circuit.

[@thomasavery4357]

Is this that equipment to do those car thefts

[@pain5140]

Hello.i have a problem with this product ..please help me.. 2 transmiters... if i clear the reciver ..selecting momentary mode with ...when clicking A or B on 1 reciver it works ..the led blinks and the relay works..ok. but

[@nigelturner5300]

Would this be possible to use for my garage gate because my key not paired anymore and I can't find the manual for it

[@nevetss14]

Hi! I got the KR2402 working with DC 6-30V! I had some troubles with the frequency! Is it possible to change the frequency used? And how? Thanks in advance!

[@qiachip]

What kind of trouble did you get into? If your KR2402 changes frequency then your remote control (transmitter) must also change frequency.

[@toske666]

I have dual relay 12v model kr1202-4. And 1 remote. i reset original remote by presing a+b buttons and my remote not work anymore, please help me?! What should I do....

[@JekaCZE]

Where i can buy remote control with 1 relay 16-20A ?

[@weechengyong3361]

Can I use it for high power device control like network switch or modem or Christmas tree LED light on off control ?

[@luisoviedo7950]

Yes

[@alolouh6785]

I have the same switch from aliexpres, I wonder the 2 led lamps you use fot test are they 220V AC or not? Thanks for all.

[@freemeusa476]

In momentary mode is it possible to program multiple transmitters to channels A & B or only one transmitter per channel?

[@qiachip]

You can add multiple transmitters to pair with receivers. Note: When adding multiple remotes to pair with the receiver, you do not need to press the receiver's button 8 times before each pairing. Because pressing the receiver's button 8 times resets the receiver, it will clear all paired remotes.

[@Siddhuvlogs__85]

Bhai kya ye center lock me kam karega autocop

[@qiachip]

Hello, buddy. I see from your homepage that you are a car enthusiast. If it is used for the central control of the car, I recommend you to watch this new video we made. kzbin.info/www/bejne/pWi2k4d4dsp0orc How to use 2CH RF remote switch linear actuator controller forward reverse rotation momentary KR2402 It is mainly to see whether the voltage is suitable for your battery. If the voltage is suitable, then it is a wiring problem. I hope it can help you.

[@Siddhuvlogs__85]

@@qiachip please tell me this remote work centre lock frequency 315 mhz

[@qiachip]

@@Siddhuvlogs__85 Our module is 433MHz. If you want 315MHz, you can contact us by email at [e-mail] . We will develop and customize it for you according to the actual situation. We hope to solve your problem and look forward to your follow-up feedback.

[@kimfraga7957]

Obrigado pelo vídeo, poderia me informar se da pra usar uma lampada de 127volts na saída?

[@qiachip]

Usamos tensão 220v, o módulo também tem um 12V.

[@kimfraga7957]

qiachip.com entendi,muito obrigado amigo.

[@hugolatino69]

Oi adorei o video ,great learning video;pode me dizer qual o melhor wireless remote control dispositivo ,para um eletric gearboxed motor carson ;rated voltage :6 vdc ,0peration voltage:3-9 and the peak torque is 600 mNm? Obrigado, gracias,thanks

[@itsme5215]

Distance range ...?

[@notis50]

I press the learning button 8 times and the led flashes several times, and then it turns off (the right led) and never turn on again. Why??? Thanks for your time.

[@qiachip]

I’m not sure, please send a video about what happened after you connected the receiver to the seller which you purchased your receiver from. Since there are many possibilities on what went wrong during the operation.

[@pain5140]

But the second reciver dont activate the relays just blinkin the led... so. Just 1 reciver works ..ideas?

[@ArjanPrins]

Hi! I just got this module. When ill connect the power on the board no led are turned on. Pushing the button does not work. I connected the power cable on L and N. Is this board defective?

[@qiachip]

Please confirm that your wiring is correct. Maybe you should ask your supplier to solve the problem.

[@jaydenritchie6351]

Brown is active blue is neutral so brown/red to Load. Blue/black to Neutral if 240volt

[@jmsssx]

Thanks sir.

[@Voknehram]

Сами пульты могут копировать другой пульт?

[@qiachip]

Пульт в нашем базовом комплекте представляет собой обычный пульт и не подлежит копированию с других пультов. Но у нас также есть копирующие пульты дистанционного управления, которые можно копировать другие пульты дистанционного управления. Вы можете посмотреть соответствующее видео: kzbin.info/www/bejne/np3RpqV9f56Dpc0.

[@boldmen1]

You forget to show the most important mode, mode 3, Inter-lock/latch mode. Will you show how to programm this mode, i'm only capable to program in this mode 1 relais and not two. with regards Evert

[@HaroldSnel]

I have the exact same problem, did you figure it out?

[@qiachip]

Dear friend Mode 3 requires a remote control with 4 buttons. Look at this video： kzbin.info/www/bejne/rnS5poetfaepa9U

[@qiachip]

Dear friend Mode 3 requires a remote control with 4 buttons. Look at this video： kzbin.info/www/bejne/rnS5poetfaepa9U

[@pochaco180]

The input voltage is 220v or 12v? Can I put a 12 volt lock to turn it on and off?

[@qiachip]

The input is AC 220V. But the output can be independent of the input, it can use the voltage range is 0V-250V, can be DC or AC. its power from the external input, then the input voltage output is the same voltage.

[@shanealam3764]

Sir is par video bna kar jarur dalen

[@fatnick2001]

Does it do interlock? I want to use toggle, BUT my issue is Its powering a curtain motor so 1 is up, 2 is down (or opposite polarity). I am trying to solve the dilemma of accidentally pushing both at the same time, turning both relays on, but possibly some output power short cicuit?

[@joeKisonue]

Ah you mean like in control contacts? Those have physical designed interactions. These are just individual relay control.

[@MovieMakingMan]

Hi thank you for the info on setting the codes but I need to know how to connect wires to it. My wired garage door opener (GDO) button just needs to be pressed once so I assume the GDO is a 'latch' type to hold the connection until the garage door is up or down. There isn't any voltage going thru the wired line. It just provides continuity between 2 grounds. It looks like the eMylo only has options to wire it up to 110 or 240, which could fry my garage door contacts. Is there a schematic that shows how to set it up. The instructions that came with the eMylo don't show any schematics. Thanks.

[@qiachip]

The receiver in the video may be different from the eMylo you purchased.

[@rozwell69]

What happens when you press both keys simultaneously in momentary mode? Will only one work or will both LEDs light up? I need to have only 1 channel active at the same time so I won't damage the engine...

[@qiachip]

When you press the 2 buttons on the remote control at the same time, the receiver will not work and there will be no output for both channels.

[@Denniss7420]

I'm still trying to figure out how the make the "ON" button work only as an ON button and not an On/Off button. I have a two button remote and prefer that the On button works only for turning On and the Off button works only for OFF. Anyone?

[@quinten250]

need this as well

[@awdhootkanawade]

3 times click latch mode

[@joeKisonue]

That would be latch mode. Don't wire second relay. Hopefully button a on b connect to open/off

[@Mightyx1jzge]

Can the receiver learn and match to work with Car remote key? It’s same 433 MHz

[@qiachip]

Hi, if your car remote key is running EV1527, then you can make it work. Otherwise it won't. But i strongly advice you to try our remote control. It works pretty well. We also got other style for you to choose from.

[@Mightyx1jzge]

qiachip.com how can i know which code is my car key running ? Don’t sure if it is EV1527. So I have order 2ch remote as following this link ลองเข้ามาดูสินค้า 2CH 433MHz Learning Code Transmitter Receiver with Digital Wireless Remote Control switch ขายในราคา ฿170 ซื้อได้ในแอป Shopee ตอนนี้เลย! shopee.co.th/2CH-20433MHz-20Learning-20Code-20Transmitter-20Receiver-20with-20Digital-20Wireless-20Remote-20Control-20switch-i.81269121.1433292853

[@qiachip]

Sorry for the late reply, the link you gave me isn't one of our product. www.aliexpress.com/item/433Mhz-Universal-Wireless-Remote-Control-Switch-AC-85V-250V-110V-220V-2CH-Relay-Receiver-Module-and/32713566439.html The following link is where we sell our product. I can't be sure what it works with base on the link you show me. We are only familiar with our products.

[@farasatali2646]

I have door opener remote control433hz i want to sencoronize an other one i have same please let me know ,thankssss.

[@qiachip]

Which type?

[@farasatali2646]

@@qiachip just for door opening A&B ON BOTH

[@leogo9945]

Hello! I bought this module from ebay and it was advertised as 4 mode module. 3 modes wich you showed on video I programmed no problem but there is mode 4 wich should be the DELAY MODE 5/10/15 seconsds. I'm not able to program it. Can you please send me any manual?

[@qiachip]

Dear friend, This 2-channel receiver has no delay mode function.

[@darkaricus4226]

My receiver has a key button but if i press it the light turns off

[@Rivuzza]

I bought a receiver the same as yours kdy 220-2. Is it programmable with a remote control of the "came 433.92mhz" ?

[@qiachip]

It does not work with "came 433.92mhz".

[@emily.souzw_]

lembrando uma coisa eu não tenho desse receptor Será que se eu comprar um desse daí gravar ele primeiro depois ele vai começar emitir a frequência porque aparentemente ele não está emitindo frequência nenhuma comprei no AliExpress mas o suporte técnico deles deixa desejar Se você tiver como me ajudar mais uma vez eu te agradeço desde já aguardo respostas sua

[@muhammadsyukrirosli1050]

Hi qiachip. can you please explain why the 2 LEDs are keep flashing from the beginning I install the curcuit and the remote does not work even though I have tried to reset the learning button

[@qiachip]

If you can upload your video, I can find the reason.

[@csepeicsabaferenc5450]

this led is 220volt?

[@AF-kp1yj]

why does it wite VDC? is it can be connected to DC power?

[@qiachip]

Hi boy zzz, As you can see in the video, the input that connected to the yellow and the red wire is running AC. Which can only be connected as AC. The side which connected to the light are capable of running both AC and DC. Hope this answer your question.

[@arturodelfranco7954]

Scusami mi sai dire come mai alla terza modalità se vado ad aggiungere un pulsante per la salita e la discesa si blocca

[@farukdiner6310]

I have question. For example I turn on the light or motor by the remote and then energy (220 volt city energy) cut off and after one minute energy (220 volt city energy) came back. Will the light or motor be on or off? Another example: The light or motor is off and then energy (220 volt city energy) cut off and after one minute energy (220 volt city energy) came back. Will the light or motor be on or off? Lets say that I am not at home and the energy (220 volt city energy) cut off and after one minute energy (220 volt city energy) came back, if the ligh or motor begin to work, it migh be very dangereous. I hope I could explain what I mean. Thanks.

[@qiachip]

Hi, First, the light will turn off afterthe power is gone. Second, if you didn't turn on the light, then the light will not start to work even when the power comes. It's safety. But you don't have to re-connect the remote control with the receiver.

[@farukdiner6310]

Thanks a lot. It is wonderfull.

[@qiachip]

Welocme. Thanks for your thought. Have a good day!

[@b7horh]

Лучший производитель беспроводных устройств. Рекомендую

[@andriiii7691]

Как его подключить к двум ролетам?

[@carlosgarcia-oq3xo]

muy bien explicado.gracias

[@bernardedette]

Can you tell me how i can makr it work just with 9v battery? I tried one time and it has worked just one time

[@truthforlife5391]

can i use this to start a generator motor ?

[@jaydenritchie6351]

Toggle run press start

[@farasatali2646]

ONE IS ALL READY WORKING I WANT TO USE SECOND SAME ONE I HAVE.

[@eqisoftcom]

220V LEDs?

[@csepeicsabaferenc5450]

i have this but i need for electromagnetical yale and i need 220 volt for exit

[@asankaranasinghe2048]

Can you please send me the wiring diagram I’m going to purchase from e bay

[@منشوراتاسلامية-ص8ذ]

What's its use?

[@qiachip]

It can be applied to the forward and reverse rotation of the motor, such as remote control curtains

[@88BlueKeys4U]

Got the EXACT same kit with five remotes (2 channels, buttons marked 'A' and 'B', identical circuit board and design). Four remotes can be correctly programmed, but one has an odd error: BOTH buttons (A and B) of this one remote will operate THE SAME CHANNEL (Relay 02), no button of this remote can trigger the other channel (Relay 01). I tried a few resets and fiddled with the other remotes; the issue with this one remote cannot be solved. Any idea what is going on here? How are the remotes internally wired/programmed to create such a mess with the receiver? Apparently it sends the same 'code' for each button A and B?? As the remotes cannot be 'cloned' there is no way to teach them the correct channel separation. This stuff is cheap (total was about $12 for the entire bundle), but I am starting to wonder how reliable these thingies are: Good that I ordered FIVE remotes, to have spares... Thanks for ideas!

[@qiachip]

Dear friend If possible, please give me your purchase link.

[@88BlueKeys4U]

@@qiachip Thanks for the reply! While all looks identical, the dealer names is not yours (but Rubrum, qq). I am not sure who is actually manufacturing these identical remote kits in China? After some tinkering, opening remotes and swapping/reseating all parts the one weirdly acting remote could eventually be programmed to a proper 'momentary mode', for BOTH channels. I still do not understand why it only addressed ONE of the two channels with either button A or B before? Is this a 'valid' operation mode at all? Thanks!

[@инкогнитоинкогнитов-ч1з]

а сделать чтоб один канал работал нажал включилось нажал выключилось, а второй включалось тока когда держишь кнопку можно?

[@qiachip]

It does not support the mode of work you require.

[@ВикторВ-к4д]

Так он тебе ровно так и показал!!! Один пульт на оба канала работает в первом режиме, а второй пульт на оба канала работает во втором режиме. Ты, вероятно, вопрос не корректно задаешь. Тебе, вероятно, надо, чтобы одна кнопка на пульте первым каналом управляла в первом режиме, а вторая кнопка на пульте управляла вторым каналом во втором режиме???!!! Приведи пример зачем это надо.

[@solostecnologia9085]

Tooop

[@versebank7865]

Tanks Brasil 2023

[@chemsul]

When the power fails, the button memory is cleared after a few seconds. Need to introduce button again. Is there a solution

[@qiachip]

Hello, our products do not come with such problem. May I have the link where you purchased your product from? You can also try our product on qiachip.com/product/433mhz-universal-wireless-remote-control-switch-ac-85v-250v-110v-220v-2ch-relay-receiver-module-and-rf-433-mhz-remote-controls

[@cokneuro7405]

how to wiring this switch?

[@techman6431]

I want 6 extra remote where buy in cheap price

[@qiachip]

qiachip.com/collections/qiachip-remote-control/products/qiachip-10-20-pcs-kt05-433mhz-2-button-metal-remote-control-learning-code-ev1527-wireless-transmitter This link is our remote control package, you can buy a very cheap remote control price We also have other types of cheap remote controls If you need You can contact our email qiachip.com I hope it can help you solve the problem

[@tnamen1307]

Sir my remote control unit does not receive signals from key. How to repair it. Keys are working fine. Just the unit is issue.

[@qiachip]

Hello, it can be caused by various issues. To answer your question, I would need a video of what actually happened. Since what you experienced can be caused by many factors. It would be best if you can also give the the receiver and transmitter specifications.

[@tnamen1307]

qiachip.com here is the receiver specs no. 6.7458 of the remote control unit.

[@qiachip]

Sir, did you purchase the whole receiver + transmitter set together? Or are you using your own transmitter(remote control)?

[@tnamen1307]

qiachip.com wholeset in one unit. I bought from international market AliExpress...

[@qiachip]

@@tnamen1307 Send a video of what happened to [e-mail] The video have to include pairing, wire connection and code clearing. So I might be able to solve the problem you are having.

[@Berghiker]

How do I modify a 12V 433MHz wireless remote control switch relay receiver and transmitter? Someone in the area (neighbor) is using the same frequency.

[@qiachip]

It is not recommended to change the frequency, it is recommended that you reset the receiver and re-pair it

[@pratheeklondhe799]

What is the range of d system?

[@qiachip]

Hello, the range is 20 meters indoor, and 80-100 meters on open space.

[@robertpandisky7784]

👍

[@javierortizdelapuentel.5325]

Gracias

[@ndjsjshshhshdjdjd9292]

where i will find the remote control for this device ?

[@qiachip]

www.aliexpress.com/store/product/433-Mhz-Universal-Wireless-Remote-Control-Switch-AC-85V-250V-110V-220V-2CH-Relay-Receiver-Module/1456073_32762475236.html

[@lakhveerlakha238]

Price ke aa sir

[@JHCMOBILE]

How to make it work at 110v?

[@RachidOUSALEM]

toggle mode

[@emily.souzw_]

Olá boa tarde meu amigo será que você pode me ajudar eu caí numa furada e comprei 40 controle de que você está na mão aí e aqui no meu país os nossos receptores são 433 e esses transmissores também são quatro 433 só que não consegui fazê-lo funcionar em nenhuma das minhas placas creio eu que é porque ele não vem transmitindo nada para que eu não possa perder lá você sabe ou poderia me ajudar com esse produto

[@relic31583]

mine turns the 12 volt lights on by itself. i turn them off and then a couple days later they are back on. Can someone tell me why this is happening?

[@joeKisonue]

You wired to normally closed?

[@eqisoftcom]

Hi qiachip. Any idea why this new 220V 2-channel receiver stopped responding to transmitters after 1 hour of usage? Note it worked at the begining, both transmitters could successfully be paired with it. They still work with another (non-qiachip) receiver, so it's the qiachip receiver that is faulty. It still responds to microswitch presses though. How is this possible?

[@qiachip]

Mickey Mouse Hi thank you for reaching out. In this condition the cause might be that the you did not clear code, we have a special step to program the remote control to prevent they will not be interface.

[@eqisoftcom]

Thanks. Well, I assumed pressing the microswitch 8 times would clear everything. As I said, it all worked at the beginning. Now none of the LEDs flashes when I press the transmitter button, and the devices cannot be paired. Is there a deaper way of clearing the code than 8 microswitch presses?

[@NOSTRA52]

I have the same problem. The remote will no longer work after a few minutes. Do you already have the solution or is it just a bad buy.

[@eqisoftcom]

No, I don't have a solution yet. I've given up. .. I remember reading somewhere that one has to be looking for a receiver with a 14-pin IC (don't know the name) rather than an 8-pin circuit by qiachip, which is not reliable. The problem is that these new receivers are flooding the market right now. .. But I am not an expert, so take it with a grain of salt.

[@anaslabanie471]

thanks

[@Neshicosmetic-gm1gk]

কতো টাকা এটার দাম

[@Perplexer1]

If that's a 220V relay then you are getting uncomfortably close with your fingers, lol. I would use something plastic or a pencil to press that programming button. Better safe than sorry.

[@joeKisonue]

It's only working on 12 v

[@csepeicsabaferenc5450]

how do i make 220 volt

[@qiachip]

Csepei Csaba Ferenc Hi! Thanks for reaching out. This receiving module kit is for 85~250V so it works for 220V also.

[@paulk9746]

But this is 220 v, please pay attention to safety

[@csepeicsabaferenc5450]

intrerupt null orr phase