Thanks! Got the track saw a few months ago and finally had a chance to use it. I had forgotten all the steps in the videos I watched when I first got it. This was a big help!!! Cheers!😊
@tribsat1004 жыл бұрын
Never ever stop on a sawcut! Continuity gives straight cuts. When you stop there is always a step in the cut line. Even more important when trimming the straight edge splinter strip. Hope this helps
@kieranfinnerty6313 жыл бұрын
Not with a Mafell track saw there isn’t, and the Bosch track is exactly the same design as Mafell
@harmenlewin96273 ай бұрын
Hi Don! Ik heb sinds kort een issue dat mn zaag klem loopt, alsof de hoek van het zaagblad niet parallel loopt met de FSN. Ik zie echter geen afstelling van de body tov de base plate. Jij een idee? Thx!
@dandyer83518 ай бұрын
Think the instructions state 9mm depth for the blade to cut the rubber.
@olofolofsson85443 ай бұрын
Hey! Does anyone know if its possible to cut at 45 degrees with the rail?
@bagoroismaelarnaud2531 Жыл бұрын
I was a little worried about installing the blade after reading a couple of reviews. But it was amazingly easy. Took about 1 minute. Works great kzbin.infoUgkxjpBI8OOeUXib_iT7UomCrQ-uauwZJ62c . Cuts easily and is perfect for pocket cuts I needed to make for replacing some old deck boards.
@jubeidono Жыл бұрын
Did the saw damage that blue rubber at the edge of the track? Mine damaged it. I wonder if that's normal.
@dexarok Жыл бұрын
Yes, it's normal. The rubber is trimmed by the saw to match your particular saw and blade kerf. This way it's correct zero-clearance for your saw and blade. The rubber is replaceable for this reason. When you change to a different type of blade, or a different saw, you're supposed to change the rubber also.
@1989ElLoco Жыл бұрын
@@dexarokThanks this could be explained clearer in the manual 😅
@dexarok4 ай бұрын
@AM-dm6jq You're very welcome. I'm very glad I could help.
@JACKSPARROW-cx8ll2 жыл бұрын
Is GKS 190 compatible?
@walteeeer2 жыл бұрын
Up
@sdg_golf5381 Жыл бұрын
Only works with circular saws and track saw models ending with G, GC or GCE, like GKS 85 G, GKS 65 GCE, GKT 18v-52 GC and GKT 55 GCE
@Thabzzz Жыл бұрын
No gks 190 is not compatible with any track
@roelonzo3 жыл бұрын
This is not how you should use it for the first time. Obviously you didn't read the instructions , you have to cut the rubber insert perfectly to the blade....
@_emanmodnar3 жыл бұрын
In the instruction-paper (version 160992A5NW, 2020.09) provided with the Bosch guide rail FSN, they show a circular saw blade cutting the rubber insert - like he does it in the video (except that he placed the blade too deep at the first run, as he describes).
@jaroslavprijmeni40693 жыл бұрын
@@_emanmodnar On the instructions there is cutting with circular saw for the first time, but on the piece of wood to prevent rubber from bending.
@_emanmodnar3 жыл бұрын
@@jaroslavprijmeni4069 Good point!
@marc1190 Жыл бұрын
@@jaroslavprijmeni4069 Yeah that would seem to make more sense to me actually
@julianbakker94362 жыл бұрын
Did you use the gks55 g or gce?
@joris38424 жыл бұрын
Even een vraagje: Ik heb onlangs ook deze rail gekocht (FSN1600) in combinatie met de GKS55+ G circelzaag. Wat ik alleen niet snap is waarom er aan de rail een blauwe siliconenstrip zit. Daar kom je met het zaagblad tegenaan en als je de zaag aanzet zaag je dus die strip kapot. Ook geeft de strip weerstand als je de zaag over de rail beweegt. Kan je uitleggen of dit hoort of dat ik iets verkeerd doe? Ik hoor het graag!
@vbdeman4 жыл бұрын
Hoi Joris, ik zal even antwoorden voor Don, =}... die strip is om splinters te voorkomen en het is de bedoeling dat je voor het eerste gebruik met de zaag de strip afzaagt zodat de de gezaagde strip precies op/tegen je afgetekende zaaglijn kunt leggen en je dus zeer precies kunt zagen. voor het eerste gebruik zorg je dat het zaagblad 10mm uitsteekt van de bodemplaat van de zaag en dan zaag je de strip af en is de geleider klaar voor gebruik. tip leg de geleider op een oude plank (zodat je door je trip en de plank zaagt de eerste keer) voor het beste resultaat. groetjes Ben
@toversnoleu87694 жыл бұрын
Precies mijn vraag! Super bedankt!!!
@joris38424 жыл бұрын
@@vbdeman Dank voor de uitleg! Ik vermoedde al zoiets. Inmiddels is het gelukt.
@twocylinderdon95634 жыл бұрын
Bedankt Ben voor het aanvullen.
@jeroenvisser46162 жыл бұрын
Dank allemaal, zou ook leuk zijn als Bosch dit ook uitlegt, maar helaas. Dank 👍
@gundur71935 жыл бұрын
how much you talked. give more visuals
@twocylinderdon95635 жыл бұрын
Thanks for the feedback!
@mattistwo4 жыл бұрын
Disagree here. This was a great video, very clear and informative.
@michaelzimmerman6352 жыл бұрын
Poorly done, 5 minutes I'll never get back.
@johanf92793 жыл бұрын
I do not understand what he is doing.
@_emanmodnar3 жыл бұрын
I didn't get this either… He is cutting the rubber insert alongside the guide rail, which needs to be trimmed for it to fit the circular saw.