Go to Harbor freight get a Easy Flux 125 Video1 kzbin.info/www/bejne/bGPQoKSXbsl8edk Video 2 kzbin.info/www/bejne/rYLJYYyGe56Ej6M
@Christopher_R7 ай бұрын
I can’t endorse it enough. I had the HF titanium, and somehow fried it, but the flux core Lincoln I replaced it with functions about the same. Order a mask and gloves, and just start messing with scrap steel. Butt joints with thin metal (like exhaust pipe) are hard, but you’ll find plenty of things to practice on.
@G.Harley.Davidson5 ай бұрын
A lot of community colleges offer an introduction to welding class in the evenings for a about two months and $400-500 dollars including equipment.
@stevenbarts3308 ай бұрын
I have the same harbor freight belt sander. Paid $15.00 for it 10-15 years ago and have used and abused it and it still works great.
@meca13b5 ай бұрын
Just across the channel, good stuff man! 400 sounds good .nice job with the welding. Liked and subbed ✔️
@jsteed4388 Жыл бұрын
Sound and video are fine. Thanks for sharing
@WeFinnaC6 ай бұрын
You just earned a subscriber I’m Gonna be ruining my exhaust this weekend 😂
@TPVPRO6 ай бұрын
You will be fine just takes a little practice.
@maldo72 Жыл бұрын
Looks good to me
@TPVPRO Жыл бұрын
Good enough for my DUD
@aros007z9 ай бұрын
Awesomeness
@bubbatennessee75315 ай бұрын
Thanks , I need to get a small welder like yours.
@TPVPRO Жыл бұрын
Video using an old Lincoln welder. Welding with cheap welders see theses useful videos. Video1 kzbin.info/www/bejne/bGPQoKSXbsl8edk Video 2 kzbin.info/www/bejne/rYLJYYyGe56Ej6M
@ZBrink113 ай бұрын
What wire are you using? What temp and speed? Thanks for the video!
@Christopher_R7 ай бұрын
Came here for advice, but heard what I already know… practice more, and sleeve your connections. I suppose I will need a LOT more practice before I am making pie cuts and welding curves to make a turbo kit 😬
@jeffreymichael11549 ай бұрын
No one ever states their settings for these flux core welders. What do u have it set at so you’re not burning thru? I can’t for the life of me get them right. Just started welding with flux core so any pointers would be appreciated. Thanks bud!
@ironwolf_65599 ай бұрын
i don’t know how to weld at all i had mine on the lowest setting with a 2 set for my wire speed you just gotta get the hang of it with a piece of scrap try to go faster if you’re burning through
@MichaelBill-el2kz8 ай бұрын
Get some scrap and test it out. You also need to to quarter your welds. Meaning weld a short distance then skip to the other side and weld. Welding thin material is all about heat input and control. Welding long beads will surely burn through. Also strike up on the thicker joint and concentrate the heat on it. Whip and pause instead of circling your bead.
@rizzoid Жыл бұрын
Guessing you only had the front loop for your driveshaft -- are there any plans to add a rear loop? Related to the exhaust: nice welds. Also, wish I had your transmission crossmember. So much better than the straight ones like most of us S-truck owners have.
@TPVPRO Жыл бұрын
I had zero loops when it broke. I'm going to add one in the middle. It's probably the only place I think it can fit.
@markkaplan1949 Жыл бұрын
@@TPVPRO Nice work. NHRA and IHRA have specs for the loop material and installation. Tech might be an issue if you go to race it and have the loop at mid point of driveshaft...
@poolsharkkkkk11 ай бұрын
what size wire did you use?
@TPVPRO11 ай бұрын
30
@randallbond5346Ай бұрын
It would be nice if when you post a video about how to weld you actually showed us how to weld. I waited 7 1/2 minutes for you to show us that you were Welding but not how to weld.
@TPVPROАй бұрын
@@randallbond5346 Here you go brother 💪🏼 kzbin.info/www/bejne/rYLJYYyGe56Ej6M