How to wire a Chuchero

A quick way to wire a chuchero without having to spend money at a local store.

[@gloriareid9000]

Very good .Excellent job well neat.

[@florestantvaldek9298]

Good job man i like it

[@richardclarke1922]

Great video thanks a lot

[@JayOnOneWheel]

you need way more details in your videos bro, good video and all but the lack of info is crazy didn't say what wires go to where, what amps to use and if you need a separate amp if you're running subs. you gotta realize majority of the people watching this have no idea on wtf theyre doing lol they might find the title misleading.

[@Kid617]

You are right maybe give some examples of what speakers are you using and what amp and the ohms as well

[@andremichael1218]

I have an 8 pin plug running 2 10's a horn and 2 tweeters. My horn cuts in and out and distorting the music. I think it might be a plug issue or a connection with the horn. What do you think?

[@Snowalchemist677]

Good video one of the few that actually explains it

[@tevitaloketi9839]

What size speaker wire do you use?

[@brandonazevedo4494]

how would i wire my 2 tweeters and 2 midbass? since i’m not using a horn?

[@davidcharles1601]

What's the end ohms load??

[@eliezerbrito301]

So is it all positives together and all negatives together?

[@premrajvish]

so you connect the horn straight to the amp ? wont that burn the horn with a straight connection . wouldn't it be better to connect negative to positive and positive to negative ?

[@teamimperium9754]

The horn can be connected directly to the amp and it will play fine, however u just got to make sure that your crossover is eliminating any frequency below 100hz and adjust the gain levels accordingly on the amp and you will get a perfect horn and tweeter experience

[@premrajvish]

@@teamimperium9754 thanks I was planning to use two horn and one tweeter with 2 six inch faital pro

[@teammember9622]

Even though i watch the video i don't fully understand. Are the two tweeters wired together? If yes wouldn't it change how the tweeter sound because of the capacitor on them probably interfering with each other.

[@teamimperium9754]

Yes there connected together, however when the capacitor is applied it changes the resistance which then allow the tweeters to play at a higher frequency than the compression driver

[@teammember9622]

@@teamimperium9754 ok thanks.

[@Snowalchemist677]

Took apart my Chuchero and the dril recoiled and punctured the speaker but e6000 fixed it up but def be careful it could have been alot worse

[@teamimperium9754]

Hey Mando thanks for sharing your experience..... what kind of speakers are you using?

[@oceano_drive241]

Kicker told me if i added speakers and horns to my sealed enclosure. It would blow them out if they did not have their own enclosure inside the box.

[@teamimperium9754]

First you would have to decide what type of enhancement do you need for your current setup. This means do you want to add more bass to your setup or more vocals or even both. The setup in this video is in regards to enhancing your vocals only. If doing a bass enhancement on your setup then yes the subs would have to be in a speaker box of its own…. Hope that helps

[@originalvibez6943]

Hi! My system is fine but one speaker is grumbling and no voice is playing can you help me

[@teamimperium9754]

Hey @original vibez i am glad to help, but I would need more details about the issue before I could make a recommendation on a solution.

[@TITORP]

How do you actually wire it to a amp ? That’s my biggest problem right now connecting the speak to my amp

[@wehavefundr647]

Mine to bc idk how to put the tweeter to the amp every time I burn the tweeter

[@teamimperium9754]

I am going to make a video shortly showing how to do so

[@UNFTHM.Gaming]

Facts. Every video on KZbin shows the same thing. Wiring everything together. But they never show what amp they use. How to wire it to the amp with the Speakon cable and where to tap into to get signal to play on the speakers

[@UNFTHM.Gaming]

Can you make a video on the amp wiring for this. Cause I’m pretty sure just like a subwoofer, that you’ll need to also get a signal from the speakers in the car to play the notes. Unless you literally just use a separate amp

[@catherineharris4746]

What background music is playing??❤💗💞💖

[@teamimperium9754]

The music is Whip - Yung Logos

[@gbrandon79]

I’m having trouble figuring out how to match an amp with a chuchero. I have a lanzar 2 channel amp with a chuchero. 2 8” prv mods and 2 4” prv tweeters. I would need to get a 4 channel amp ?

[@teamimperium9754]

Hey Brandon, a two channel amp could work fine as long as it has independent control settings for each channel

[@gbrandon79]

@@teamimperium9754 ohhhh thank you so much! I have been trying to figure out why my chuchero sounded so terrible and it’s because I don’t have individual channel settings. I guess I have to get a new amp! Thank you!

[@teamimperium9754]

No problem glad to help!

[@carlosramos1207]

I dont know how to wire up the speakon connector for the chuchero

[@teamimperium9754]

Hey Carlos are you reffering to the male or female part of the connector?

[@carlosramos1207]

Do you have an instagram or any social media where i can contact you?

[@teamimperium9754]

Yes social media is team_ imperium_motors

[@losoway4505]

Only mid bass speakers goes in a chuchero?

[@teamimperium9754]

@loso way 450 The speakers that you put in a chuchero is completely up to your listening preference....whether you want a more punchy bass ready chuchero or just a loud mid range version

[@losoway4505]

Thanks bro

[@OceanzMadeIt]

I’m doing mine (2 midrange and 2 tweeters) and want to know how you would wire them all so the total impedance would be 4 ohms .. and what ohm speakers would be needed ... it’s gonna be on one channel (bridged)

[@teamimperium9754]

Hey @Oceanz Made It if you get two 8 ohms speakers and wire them in parallel it would be 4 ohms

[@OceanzMadeIt]

@@teamimperium9754 I know that part but for 4 speakers? How do you wire 4 speakers to get 4ohms final?

[@firestick4394]

@@OceanzMadeItIf the 2 midrange speakers are 8 ohm connect together in parallel wiring for a 4 ohm load. If the tweeters are also 8ohm then connecting them parallel would be a 4 ohm load. Don’t use tweeters and midrange on a single channel together because it will cause the tweeters to play midrange frequency’s including midbass which will cause the tweeter to be messed up and burnt.

[@firestick4394]

You wouldn’t be able to set the crossover individually on the midrange speakers and tweeters.

[@ralphrosario1]

Do you have the speakers and the tweeters connected together or your running a separate amp for the tweeters

[@teamimperium9754]

The speakers/woofers are on a separate amp... however the compression driver/horn is connected together with the tweeters... and all you may need to do is to include a capacitor on the tweeters and it will raise the frequency level allowing the tweeters to play at a higher hertz

[@ralphrosario1]

@@teamimperium9754 ima start uploading some videos so you can see I have a crazy set up just haven’t set it up lmao

[@teamimperium9754]

Great! Would love to see it... you can send reach out to us on Instagram @team_imperium_motors

[@ralphrosario1]

If you only knew how many people want to know more on this lmao I’m one of them I have it all just haven’t put it together

[@teamimperium9754]

Lol yea it can be tricky. But just let me know what yall don't understand and I will try to explain the best way i can in further videos

[@gun5z617]

Can u drop a diagram how how u connect everything to the 4 pin connecter that’s the part don’t understand thanks bro bless

[@gun5z617]

@@teamimperium9754 ⬆️⬆️⬆️⬆️⬆️⬆️⬆️⬆️⬇️

[@MarioHernandez-xy8pu]

I need help with everything I want to run one in my room or car

[@djnyahworldwyde]

Jamaican?

[@fullpeladas]

Not good explanation at all