In this video we will discuss about working of pir sensor how to work pir sensor
Пікірлер: 23
@BMSToons19 күн бұрын
आपने लो और हाई उल्टा बताया है।
@ersomesher2 ай бұрын
How to connect a 12V LED strip light directly to the sensor without using any resistor or transistor or a relay. The LED strip light will be powered by 12V 5A driver. The setup will be mounted underneath the kitchen platform. The LED strip light should turn ON when the drawer is opened. Why are transistor and resistor mandatory? What would happen if remove them and connect LED strip light directly? In case if direct connection, will the strip light get damaged or the pir sensor get damaged? Or neither of these will get damaged and LED strip light won't glow?
@kunaljatav4561 Жыл бұрын
Sir timer circuit bnao
@doexperiment6433 Жыл бұрын
Nice video
@sandeepgupta6526 Жыл бұрын
Nice , thanks
@Inventor129 Жыл бұрын
You most welcome dear
@anandjoshi8554Ай бұрын
@@Inventor129 continuous movement nhi ho to band hoi jata hai , outout > 23 sec + retrigger + highest distance setting me bhi !!) ( shayad toilet jaisi small jgh ke liye thik hai, room ke liye nhi !!!
@VinodSharma-pt5gr8 ай бұрын
amazing
@Inventor1298 ай бұрын
Thanks dear
@Officialshyam21 Жыл бұрын
सर वेरिएबल पावर स्प्लाई बनाओ
@anandjoshi8554Ай бұрын
continuous movement nhi ho to band hoi jata hai , outout > 23 sec + retrigger + highest distance setting me bhi !!) ( shayad toilet jaisi small jgh ke liye thik hai, room ke liye nhi !!!
@Inventor129Ай бұрын
If you made a external circuit for this ...then you will be able to receive desire output
@anandjoshi8554Ай бұрын
@@Inventor129 I have used 5v dc supply + bc547 npn with 1k resistance at base + in4007 in a 5v relay + high continuous trigger > what do u mean by external circuit? and please tell me > what to do to decrease its output time, so that it shut OFF the connected load before 23sec ( as I have set 23 sec delay, it shut off the load also after 23 sec !!! after I leave the room) should I use off delay timer relay in place of 5v relay ?
@BMSToons19 күн бұрын
आपने गलत बताया कि लो और हाई उल्टा बताया है।
@bajlurrahaman611113 күн бұрын
Faltu chij paisa barbad or kuch nehi koi motion nehi toh bhi light jalta he jolta he to fir off nehi hota he 😢 have any solutions?
@swatstudio260710 ай бұрын
Ye outdoor lag sakta ha
@riyajmondal631211 ай бұрын
Raat me ghar pe lagake use kar sakte he? Taki chor bagara na eaae...
@Inventor12911 ай бұрын
Hji raat me bhi chlaga ...
@deepakDBD9 ай бұрын
Op
@mayuritekar67938 ай бұрын
How to run 12v led on this device
@Inventor1298 ай бұрын
Pls chk kijiya mera channel parr
@optoopto44748 ай бұрын
Bich wali to mara wala 1volt da raha ha😢
@ersomesher2 ай бұрын
How to connect a 12V LED strip light directly to the sensor without using any resistor or transistor or a relay. The LED strip light will be powered by 12V 5A driver. The setup will be mounted underneath the kitchen platform. The LED strip light should turn ON when the drawer is opened. Why are transistor and resistor mandatory? What would happen if remove them and connect LED strip light directly? In case if direct connection, will the strip light get damaged or the pir sensor get damaged? Or neither of these will get damaged and LED strip light won't glow?