Husqvarna 450 Chainsaw Review - How to Cut Firewood

Husqvarna 16 in. 16 Inch 120 Mark II Gas Chainsaw
amzn.to/2IzjS9k
Husqvarna 20 Inch 460 Rancher Gas Chainsaw
amzn.to/2N3WKFH
Husqvarna 587160704 Technical Apron Wrap Chap, 36 to 38-Inch
amzn.to/2Rua0ly
Husqvarna ProForest Chain Saw Helmet System
amzn.to/2N5vKFW
Forester Chainsaw Apron Chaps with Pocket, Orange 36 Length
amzn.to/2J3hgki
Oregon S56 AdvanceCut 16-Inch Chainsaw Chain Fits Craftsman, Echo, Homelite, Poulan, Remington
amzn.to/2Ivhe4v
Viking Footwear Class 2 Chainsaw Boot,Orange/Black
amzn.to/2Fv5yye
This is a good review of this chainsaw. A homeowner special with 18" bar but cuts just fine.

[@brandonbowman4707]

Good video

[@rep1989]

how how this saw held up? My old husqvarna 350 is about done and was looking at teh 450 rancher

[@ГеоргиДюлгеровъ]

Any problems with husqarna 450 ?

[@ifoundjim]

It's been a great Saw 🪚 overall.

[@jimbob-tz4zb]

Saw dust looks a bit "dusty" chain needing sharpened or rakers taken down ?

[@ifoundjim]

probably... can you show me your video cause I'm always into learning... really... ALWAYS and thanks!

[@jimbob-tz4zb]

Meeoooow ! no need to get touchy man. Would it not make sense to sharpen your chain before doing a "review" ? that way the saw would zip through that log like it should and you wouldn't have to lever so hard with the bucking spikes and fuck up your isolators. No need for a video...it's pretty basic stuff. Anyway, i'm still on Super 8mm .

[@chrisgrayston1982]

Dust = rakers down

[@Semiel6721]

Хорошая пила

[@drodriguez3935]

Is it 18” or 20” the box says 20” on the 450 farm tough

[@brownwrench]

Nice log there.

[@fuelediowa]

the 450 is a good all around saw. you are definitely working it. lol. do you have any update a year latter?

[@coreyriley7160]

Nice work! I have the same saw, mine doesn't seem to oil enough. maybe 20 tanks of fuel through it, never ran it out of oil. bar is turning black/blue. I go through half tank of oil per tank of fuel.... any thoughts ??

[@ifoundjim]

Corey Riley sound like your oiler is plugged

[@coreyriley7160]

Any clue how a rookie firewood cutter like myself could fix it ?

[@alittlebitofeverything5090]

Corey Riley Hi, take the bar off and clean the hole that is located on the side of the bar. There should be one on the other side of the bar for when you flip over the bar to wear it evenly. I usually take a small twig and unplug the hole or spray WD40 through it. The hole should have no obstruction and you should be able to see light through it.

[@lyricderbin1169]

There's an adjustment you access from the bottom of the saw that controls oil flow.

[@ExtraAlterMone]

@@coreyriley7160 just unmount its oiler and re-drill it from OEM 1.5mm hole to 2.5mm....I did mine to 3.0mm and it oils too much :)

[@cassidylockard1527]

I have the same saw do u think it would hurt to put a 24 inch bar on it

[@lyricderbin1169]

If you do the muffler mod and full skip chain

[@timgile8144]

what chain are you using

[@ifoundjim]

Tim Gile OREGON