Husqvarna 455 Rancher Chainsaw Will Not Run

[@allegory7638]

I just got this exact saw free off someone's curb, couldn't believe my fortune. It had cracked fuel lines and primer bulb. Tricky carb removal on this one. Took the carb apart and the diaphragms/flap gaskets were good and pliable. Runs great now!

[@derpherpp3]

must be nice dumpster driving around nice neighbors

[@AllaroundNbackagain]

Glad you left all of the steps etc in there to see how it came apart. Mine is really bogging out so I need to go through it soon

[@henrygrey346]

Diagnosis is especially critical. Get it right and 50% of your job is done. The other 50% depends on your skill set and knowledge. Good video.

[@williammoore5924]

Howdy, good afternoon to ya. I just received a 455 Rancher as a gift and needs some Cleaning and possibly new fuel lines. So, this Video was helpful before I attempt to Repair and or diagnose it’s issues. Good job Tks for sharing your time and knowledge.

[@brucehedge7257]

Hi from Australia... after taking the top off, I could see the fuel line had perished/split where it came up from the tank below and entered the carburettor. Looked in fuel tank, saw there was an excess of two or three centimetres, so figured I could pull a centimetre or so through. I'd never have figured out how to de-link the throttle linkage! . Your video helped so much, thank you! I didn't know how to get the carby out far enough to pull the split bit of fuel line off and slide the new bit over. Your excellent instructions saved me a trip to the local repair shop and a hundred bucks, or so I suspect! It took a bit longer, cos I didn't have a suitable hex screw driver, but managed slowly with an allen key. Thanks again! They are VERY good saws- have had mine through at least ten chains , two bars, and a sprocket.

[@chriserickson4417]

Thanks for the video. It has helped me with my chainsaw problems.

[@SmallEngineDIY]

Glad it helped

[@willssmallenginerepairllc5060]

Just repaired one and they aren't too bad to work on. To diagnose a no start I have a squeeze bottle of mixed fuel that I squirt down the carb and then give the rope a pull. If it runs for a second that tells me that it has spark and compression then I will investigate the fuel system. I always pull the muffler on 2 cycle equipment to look at the piston too.

[@MJ-no4gt]

This guy really knows his stuff I'd give him 5 stars

[@bobstar1989]

Why didn't you replace all the fuel lines they were all pretty old probably wouldn't it be?

[@pipedreams57]

Nothing beats a good steel 5" VISE for working on saws, especially when it comes time to yank your guts out getting it started and adjusting the carb, LOL. Works great for sharpening too.

[@catpeople1958]

I actually had a vise mounted to my truck when I was selling oak firewood on the East coast. Best thing ever for sharpening. You got it! 😊

[@cogentdynamics]

It would have been very helpful if you would have showed the fuel hose routing and which are ins and outs. Also your testing procedures on the primer or purge bulb. Thanks for the good video!

[@sondon7103]

Great Bang for your Buck Performance

[@pipedreams57]

Geeeezzzzz ! I have an older original 55 Rancher made in 2004 which has been trouble free and easy to service [stuff like the fuel lines and air filter is all that has been touched]. Looks like Husky really cheapened their 455 model and made it MUCH harder to work on. Mine did go under water one time during a flood. It ran ok when I fished it out but the coil went dead a few days later,..guess it got water saturated and shorted out. It has the original 20" bar on it and I have went through 4 or 5 chains but that is nothing. I never leave fuel or oil in a saw when I finish using it is the key to problem free service.

[@micmichaeladflak6373]

My 460 stopped dead the other day. wouldn't restart. after removing the intake cover I could see she was wet inside the case. Spark tester was showing spark. then after pushing on the primer bulb I could see fuel seeping at the carb inlet tube and then realized my thumb was wet. primer bulb cracked also. she's 10 yrs old and I guess all the plastic lines have served their time. I have all new fuel lines, filter bulb carb kit coming from h&L $55.00 in total but hey she will be good as new. love these educational vids. thank you for your time and knowledge and sharing that knowledge with others.

[@mtsflorida]

Always put your air filter on and your bar and chain before pulling to start you don't want dust going into intake or sprocket coming off.

[@keithclark486]

Just the clutch cover will do?

[@mtsflorida]

I only saw you replace one yellow fuel line and trimming black fuel line, what about the yellow long vent line?

[@sting1111]

On my 450 I just pulled out the carb. It should not be that freakin hard to pull it out. They should have made it easier to service. I was worried I would cause an intake leak as I struggled getting it in and out but it runs fantastic after I cleaned the carb.

[@ianritchie126]

The first thing I do with any non runner is check compression then if that’s ok put a drop of fuel straight into the cyl , if it fires you know it has spark so it’s a fuel problem , could be other problems also etc

[@mtsflorida]

Two other components he didn't mention that go with compression, fuel and spark are air from intake filter and electrical circuit or cut off switch.

[@philliphall5198]

It’s fixing to be summer 2024 and it’s allready hot up here on I20 Hope you’re doing well 😊

[@SmallEngineDIY]

👍👍

[@angelaprater2679]

Mix on gas and oil 50 to 1.on the Rancher have one. Good video thanks

[@OGColorado]

Great video! I just liked and subscribed. Good luck on your channel growth.... These are very helpful.

[@SmallEngineDIY]

👍👍

[@jamesdondanville1008]

Awsome man..! thanks for taking the time to make this video... Swapping out my carb tonight.

[@mohammedshafeeq9330]

V good tip I like v much it will help me thank you.

[@henryalvares7672]

first step pour small amount of mix gas in the piston and if fires up you know is fuel problem.

[@praetorianpatriot3267]

80% of all small engine no start issues is fuel related. The other 10% is electrical and 10% is carb adjustment.

[@scottthompson5516]

Enjoy your video's

[@SmallEngineDIY]

Thanks 👍👍

[@WilliamJones-sq8ln]

I have the same saw where fuel line dry rotted having to do basically same thing but it was, or seemed easier removing the carb disassembling the top handle/grab bar as well as the throttle handle but now re assembly was a pain as far as throttle linkage routing and back up inside throttle trigger this being my first time on the 455 rancher I could be doing it bass ackwards

[@earltharrisjr6955]

I replaced my carburetor with a Walbo kit from Amazon. The Rancher 455 fired up on first pull. However, when i pushed the choke in the saw was still running fast and when i squeezed the throttle it would bog down like it was trying to stall. What did I get wrong on the install? Do I need to adjust the carburetor?

[@SmallEngineDIY]

Sounds like the carb needs adjusting. Running too rich and floods with the throttle. Try adjusting the air/fuel mix on the high side.

[@cobhc1986]

Just a quick tip, on the 455 and 460, I find it easier to remove and replace the carb if I take the whole handle assembly off. Just 3 screws and the whole engine assembly can be taken out of the handle. Makes it a lot easier getting to the bottom 2 screws holding the carb on.

[@SmallEngineDIY]

I'll try that next time...

[@philliphall5198]

These are pretty good saws and just need service

[@SmallEngineDIY]

They are pretty popular around here.

[@two-strokeworkshop1154]

How do you get that sound is the muffler that makes that kind of whistle

[@caldreamin09]

I replaced my carburetor it looks like that went great no leaks everything looks good seems to work but my compression super tight now. I can barely pull the cord I took the spark plug out and rotated a few times put it back still way tight any ideas you have which may help I would really appreciate. Thanks

[@brucewayne3396]

Having the same problem with the husky 55 rancher. When you find out please lmk!!

[@paulserrajr4914]

Why didn't you change the gas first?

[@stewartdaniels2874]

I had the same problem on my 455 rancher must be ethanol fuel I change it yesterday 👍👍

[@sajidrafique375]

At 22:00 what were u adjusting? Husqvarna has a special tool to adjust idle ..very special ...

[@Boost_Addict]

yea that flat head did nothing....

[@trimbaker1893]

@@Boost_Addict I noticed that too...busted on the adjustment... but, it runs. : )

[@michelbrown1060]

Today after taking appart my Husky 240; clean, blow it clean, carb, chain, blade and carb. . . .It would run about 10 minutes and stop. . .like it did 2 days ago with plenty of gaz in it 🤨 so iIobserved what I was cutting. . . .Then I saw the Light 🤩This small Husky 240 does not like cutting in the vertical plane. . up in my arms. . .Probably that the big fuel filter sucker is too big and it does not go th the lower side of the gaz tank. . .In horizontal, it will empty it's tank all the way 😁 Halleluya HAAAAleluya Haaaaaaleluya Haleluyaaaaaaa🤩

[@johndoe7268]

Thanks. I can do that.

[@209porker]

I have a different model, a 135 but the carb arrangement is similar and showed how to remove so thanks for that. (Mine idles but won't rev so suspect fuel filter carb diaphram)

[@roymills415]

Hey Matt did you check your low needle setting, often if it won’t throttle up the low is set too rich. Should be 1.5 open from fully closed.

[@209porker]

@@roymills415 - Put a carb kit on it in the end and that fixed it and vowed to use non ethanol fuel which here in the UK plays havoc with 2 strokes that aren't used often.

[@roymills415]

Awesome !! Can’t find non ethanol here in New England, I make by own by adding water to remove the ethanol, only for engines I care about!

[@garychandler4296]

I have one on my bench, not starting, but trying to; air filter clogged, so that first thing in the morning: it's Miller time! You checked the coil, but didn't check the plug next. I saw a guy rebuild an engine only to find out the plug was bad, funny as hell! I always say K.I.S.$. first, LOVE later!

[@wharris7594]

broken fuel line from the primer bulb. your welcome.

[@keeganfoster1792]

Have a old husky was using it to cut wood and it was idling on the ground and it shut of fast and randomly saw was very reliable too. It turns over but once every time pulled over it kinda grabs some some but then will turn fine then grab again. Any idea or help?

[@TheKrayusKorianis]

Check the air gap between the flywheel and ignition coil. Pretty sure the gap is gone.

[@bubba7531]

Helpful video. Thanks for taking the time.

[@nathanb2076]

appreciate the detailed video, helps alot.

[@brawlbear1555]

ewww de

[@adnacraigo6590]

Seems like every few years you have to replace all your fuel lines.

[@SmallEngineDIY]

They definitely get old👍

[@gypsydrumhorse]

Mine is same model. It sucks gas too fast and sucks it right out of the fuel tank. Carburetor has been cleaned and adjusted. Bulb is good, lines are good. It won't start again when the fuel gets sucked out of the tank. It sucks the tank dry. Makes me crazy....

[@gypsydrumhorse]

filters are good and clean

[@xxResistOrServexx]

fix it yet ? sounds like same issue i have . havent done tear down yet . had it over 5 years pretty decent saw until now......

[@roymills415]

Sounds like a bad diaphragm in the carb. It’s stuck open. Ethanol in the fuel reaks havoc on the diaphragm.

[@hunter1953]

Nice job and that is why I do not work on chainsaws

[@OseanMossfeet]

you may have found the 4th component! Compression! THANK YOU! I think the idea to remove the muffler and check cylinder itself will be my fix. :) The usual 3 are: Fuel, Spark, and ... AIR.! ;) Good airflow is also beneficial.

[@budsbustbi6339]

i have 4 of these!! bad carb is the #1 i change them out and new saw!! i have rebuilt one on self!! the new gas eats the gasquits!

[@hugostiglitz4777]

My 353 won’t start. Any suggestions?

[@aorsin]

seems to be a great video if it were not for the so many ads coming up

[@AmericanRusticWoodworks]

Decent video but you really should have pulled the spark plug out of the cylinder first and checked it even though that wasn't it that's what you do first with a chainsaw

[@roymills415]

True…Spark tells you a lot about how engine is running, if you know how to read it…

[@robertmoreland1220]

Primer bulb do not push fuel primer bulbs pull fuel through the carburetor and return it to the tank

[@davebarnessr.5805]

I’d dump the old fuel before I did anything, if it’s been setting a long time!

[@buddyindigo]

lol he just pretended to tune it.

[@stevenkelble5248]

good video thanks

[@marcduclos9789]

Thank You

[@jasonblanton7185]

The title should have been this saw wont run because I worked on it !!!! Bahahahaha

[@johnwallace1729]

why spin a screwdriver , when you have an Milwaukee M-18 right there ?

[@DirtNastyy]

Strips threads breaks bolts and Easy to over torque it’s best to take your time with small engines

[@kellyronaghan5587]

I use 40:1 in all my STIHL chainsaws

[@Boost_Addict]

Google:50:1 All STIHL gasoline-powered equipment runs on a 50:1 mixture of gasoline and 2-cycle engine oil. Knowing the proper way to mix your fuel is the first step in keeping it running strong and long. Before mixing, read your product instruction manual for additional information on fueling and fuel mixtures. Award silence .....

[@kellyronaghan5587]

@@Boost_Addict I just feel I'm being safe with the extra little bit of oil that I use. Not like its gonna hurt it

[@TheKrayusKorianis]

50:1 is for the EPA, it's safe to run 40:1 or 45:1 ratio. A bit more oil will help protect the engine.

[@gilberthathaway1655]

@@Boost_Addict a mix of ever clear and mink oil at 2:1 is what a guy told me, said it smoked and stunk but chugged along.

[@MrFamilyMoments]

The gas lines always break

[@TheUltimate65]

Dont forget and fitted the chain..

[@hidhshsj123]

Of course it wont its a Husqvarna

[@omarnajoormeerah8459]

Harga aspana 288

[@noelpeterson5591]

I always throw that screen away.

[@SmallEngineDIY]

Many guys discard it. It is just a safety factor for starting a fire from the sparks on dry saw dust.

[@noelpeterson5591]

​@@SmallEngineDIY Yes, I know but it's just waiting to get blocked.

[@eugenefredrickson8714]

Am i the only one cringing watching this feller fight the carb. So much easier pulling the motor out of the chassis.. 3 screws and TA-Da.... Access....? K

[@budsbustbi6339]

on this model it easier than that!!2 rubber monts on each side pop them off carb lifts up so you get right to the screws

[@eugenefredrickson8714]

@@budsbustbi6339 you're right.. i stand corrected.. Thanks

[@waynedupuis6489]

Gi Anishinabe ina?

[@jasonblanton7185]

Its 50 to1 lol and if you are repairing saws for others you really should have a tachometer to set the idle rpms and the running rpms, otherwise you are taking a risk letting the owner blow his saw up not realizing that you arent really a saw repair shop !! It's not lagit brother, it may run but you need to have a tachometer to set the rpms!!!!

[@pipedreams57]

My old 55 has 2 bucking spikes. This thing looks like it has only one and judging by the design, I'll bet those are hard on pants and chaps. What a POS.

[@jasonblanton7185]

I bet you charged for a new pulse line didnt you!! You should have replaced it ,given it's a customer saw and not your own!!! Things like that are why I will never take one of my saws to any saw shop period !! It's just how it is folks and you are more then capable of repairing your own tools and such !! I mean really if this joker can pull it off you surely can ! Just saying folks I'm just saying

[@jasonblanton7185]

Definitely dont let this joker work on your saws ,he doesnt even know what gas oil mix to use and he doesnt know even what his gas is mixed at ,uhh it's like 40 or 45 something like that lmao lol !! Must be a city dweller lol

[@johnwallace1729]

im a city dweller and its 50-1 duhh

[@jasonblanton7185]

Not to mention hes not using a tachometer to set the carb properly !!!!! Not a pro ,just a Joe!!