Hey Mike! That was an amazing video! I've always wondered about skip chain. Looking forward to trying it myself! Extra points for cutting in deep snow!❄️❄️❄️
@Lifeinthe906 Жыл бұрын
Thanks John. Didn't notice a big difference in the cut. But it sure is nice to sharpen !
@johnbaenen5386 Жыл бұрын
you just reminded me how I got to get out there and cut next year's supply.
@Lifeinthe906 Жыл бұрын
Sometimes it is hard to get started on next year's wood! Thanks John
@Thetreefella Жыл бұрын
I've run skip tooth for years on my 36" bar on my 460 mag. Haven't used a smaller bar than that with skip tooth chain. Good video mike. Hope alls well in your neck of the woods 💚🌳👊👍
@Lifeinthe906 Жыл бұрын
Thank you sir! 💚🌲🌳👊
@outdoorsinthe608 Жыл бұрын
I haven’t ran a skip tooth in a while but when I did I liked it! Easier to sharpen👍👍
@Lifeinthe906 Жыл бұрын
Thanks Jeremiah. Yep the sharpening is my favorite part so far.
@HuntingFarmerOfficial Жыл бұрын
It worked although probably not perfect in every situation. Good info on the pros and cons 👍
@Lifeinthe906 Жыл бұрын
Thanks Dave. Gonna try it out for a bit and see how it goes.
@canvasman2307 Жыл бұрын
Mike your run down of the pro v con for a running a skip tooth chain are spot on. Assuming we all follow safe saw operation practices and wear PPE… put keeping in mind when brushing out a felled tree that you may be in the danger zone if you cut a limb horn, burl, knotty section or other section of fling-able wood and gravel. Ask Chris and Kenny about the impression it can make on a feller 😂😮
@Lifeinthe906 Жыл бұрын
I try to be mindful of tension in the wood and do the best I can when it comes to safety. The tops being under the snow also makes it more challenging.
@canvasman2307 Жыл бұрын
@@Lifeinthe906 Yep your approach looks well thought out and deliberate. My comments were more to the end that the skip tooth chain makes catching shrapnel more of a real risk when felling, limbing, and bucking up trees in the woods. Chris had a chunk hit his shin and still fly across the new Woodyard. I’ve been dinged before despite my best efforts
@Lifeinthe906 Жыл бұрын
@Canvas Man OH man the shin is not fun!!
@michaelwhiteoldtimer7648 Жыл бұрын
Mike I run a skip tooth chain on my 24 inch bars, it’s really nice when it comes to sharpening
@Lifeinthe906 Жыл бұрын
Yes sir . I like that part the best so far!
@knottwworking Жыл бұрын
Have a great day Mike!
@Lifeinthe906 Жыл бұрын
Thanks! You too.
@andrewscott2866 Жыл бұрын
Good job👍👍.Very similar experience as I had. You might be happier with the skip on the harder wood, I was tempted to take the rakers down but scared it would make it too grabby when limbing🤷♂️
@Lifeinthe906 Жыл бұрын
Thanks Andrew. I thought about taking the rakers down for a minute then decided to try it like it is for a bit.
@casterman2 Жыл бұрын
Good stuff Mike!
@Lifeinthe906 Жыл бұрын
Thanks Winston
@driftlesshunter9200 Жыл бұрын
I think using a full skip chain on any bar over 20" on a 50cc saw is good advice. If I were using an 18-20" bar, I would stick with a full-comp chain. A full-skip for a 24" bar makes sense (especially on hardwood like oak), but I agree that the difference is not going to be drastic!
@Lifeinthe906 Жыл бұрын
It definitely makes sharpening a lot faster. I'm gonna run it for a while got lots of hard maple to cut .
@Living-The-Dream Жыл бұрын
I just bought a skip tooth chain 28” for the MS 500i. Will be interesting to see how it does and how it runs. It is probably just me, but your’s sounded like it was hitting higher rpm’s …..look forward to seeing what you think after running it awhile Mike. Especially after using it on some real solid hardwood. Appreciated the video 👍🪵⛓🪚👏🤜🏼❄️🤛🏼 Rick
@Lifeinthe906 Жыл бұрын
Thanks Rick. I'll definitely run it for awhile to get a better feel for it. It sure is nice when it comes to sharpening it 😆
@davidvankainen67119 ай бұрын
Interesting you didn't report any problem with full chain on 4" "oversized' bar. Can understand it, my pre 'rancher'' 450 has no prob with full 20" only 3.2 vs 4 HP! 550XP M II looks bad to the bone. Maybe skio chain if 28" bar? Skip chain advantage: less teeth to sharpen.
@Lifeinthe9069 ай бұрын
I have run 24 inch skip. I would try a 28 but I don't have one. I'm real happy with the 550
@firewoodathome Жыл бұрын
👍👍
@Lifeinthe906 Жыл бұрын
👍👍✊️✊️
@adammoggysawmilling5164 Жыл бұрын
Lol I literally just watched your other video on this earlier this morning 😂😂 I'm curious was a 24" bar available in the smaller size chain or was that why you switched to the 3/8 chain I've been wanting to get a 550xp and would like a 24" bar as it's my favorite size
@Lifeinthe906 Жыл бұрын
Hey Adam. I believe the longest bar in .325 I could find was 20". I did want to switch to the 3/8 chain anyway because I run that same chain on my 2165 jred. The 550XP Mark ll has been a great saw.
@eddyarundale1566 Жыл бұрын
👋
@Lifeinthe906 Жыл бұрын
Hey Eddy 👋
@dirtyrotter4057 Жыл бұрын
Well the way it acted there i would not run a skip tooth chain.
@Lifeinthe906 Жыл бұрын
I'm not a fan of the skip tooth. It's about worn out then I will go back to the full comp.
@toddsoutsideagain Жыл бұрын
I have never ran a skip tooth! I’m on the fence whether you gain anything 🤷♂️ I bet they would be good if ya had to do some noodling? Then again what do I know I’ve never ran one😂 Thanks for the info Mike👊🏻
@Lifeinthe906 Жыл бұрын
I'm definitely still on the fence with it but..... it sure is quick to sharpen and I can appreciate that 😀
@davidvankainen67119 ай бұрын
Noodling? You talking about cutting a hole in the ice to grab catfish?
@toddsoutsideagain9 ай бұрын
@@davidvankainen6711 🤣Not that kind of noodling. I’m talking about cutting firewood rounds with the grain.