Thanks for sharing - I was just about to buy a fender eliminator but watching your video saved me around $170. I basically did the same thing you did and it worked out great.
@MotardSteve6 жыл бұрын
+Dave Troughton Awesome to hear man. I figured any money saved on stuff like this means more cash to spend on other stuff like exhaust and crash protection.
@psyfertech3 жыл бұрын
r&g make a killing on their tail tidys and its always out of stock or you have to order from europe and wait ages to get it, i found a cheap 30 dollar one on ebay that comes with a cheapo tail light but then i went to chaparall and bought the DRC tail light its the same one crashking from supermofools used on his 690 recently it looks like it was meant to be there
@Shawn-in-da-Canyon6 жыл бұрын
Instead of drilling a big hole for the wires, I'm thinking about making a groove at the top to put the wires through. I think the wires would be more snug and less water can get through.
@MotardSteve6 жыл бұрын
Yeah that would work too. I didn't think much of that but I doubt either way you'll have an issue with water getting in
@aRemter19967 жыл бұрын
Hey Steve I'd recommend cutting out a piece of Lexan or some kind of backing plate for your plate, adds a lot of strength and my plate hasn't had any problems whatsoever.
@MotardSteve7 жыл бұрын
+iAmWIRide I may do that because when I looped the plate got trashed pretty bad, but I was able to hammer it out flat again luckily.
@dandamiani200 Жыл бұрын
Awesome video bud. I’m about to do the same to my 23. I’m surprised that saw made it that long!
@Shawn-in-da-Canyon6 жыл бұрын
I'm also thinking about drilling two holes in the fender to mount the light. I think it would look ok with the black screws that hold the light.
@Duken4evr29 Жыл бұрын
Good common sense video, I did similar with my 701 Enduro. Useless tail tidy savings applied to Rottweiler goodies (O2 sensor dongle, canister and SAS deletes). The engine is far less covered in hoses now and it's ass no longer looks like ass - LOL
@hrbestalkinme36906 жыл бұрын
I purposefully run my plate connected loosely with zip ties and only at the top two mounting holes. That way it flaps in the wind and exhaust vibrations, and cops can't read it. If they run my plate, they will see that i only have my temps and should not be riding at night. Also, it keeps that shit from snapping off when I scrape fender
@TheStarkBiker7 жыл бұрын
crazy how diffrent the lights are from the europian ones.. a lot smaller than yours. well done tbh with the fender!! :D
@MotardSteve7 жыл бұрын
+Stark Biker Yeah I wish we had the tiny square tail light on ours here and the led signals. I guess one plus is we dont have the giant square license plates here. Haha. Thanks man. I think it turned out pretty good.
@exnihilo4157 жыл бұрын
This is the kit you want to buy if you want to do the usa blub to euro led conversion. Worked great on my 701. www.ktm-versand.de/product_info.php/language/en/products_id/646145
@TheStarkBiker7 жыл бұрын
MotardSteve True! our plates are so huge and ugly.. like 5 year ago it was even smaller than yours an de now twice as big.. 😂 hahaaa
@nickellis83627 жыл бұрын
You used a masonry drill bit 😂
@MotardSteve7 жыл бұрын
+Nick Ellis Ha my friend said the same, I was like I thought all drill bits were the same....😂😂😂 fail on my part.
@MotardSteve7 жыл бұрын
It should be a crime to put such an ugly piece of junk on such a purely beautiful work of art, But really though, who wants to spend a couple hundred bucks for a kit when you can do the job yourself for pennies.
@billymckee94387 жыл бұрын
I would pay the money for one if they kept the nice big tail light. I've only seen two kits, one with a tiny LED strip that includes blinkers / illegal plate position for CA, and another with an ugly red tail light. Your way is the best bet so far.
@MotardSteve7 жыл бұрын
Billy McKee Yeah the bikelitez one is stupid looking and the R&G one isn't much better. plus they are both upwards of $200
@dominicthorburn69225 жыл бұрын
The reason you struggled drilling the fender is because you were using a masonary bit ...
@MotardSteve5 жыл бұрын
Lol yeah my dumbass found that out after the fact 😂
@KeepOnJeepinOn7 жыл бұрын
Must be the hardest plastic ever lol. They're really getting their money with those $300 ones, I think my DRZ cost maybe $100. The bracket was 40 of that too
@MotardSteve7 жыл бұрын
+MotoJeeper Yeah I looked it up again and it's closer to 200 but still, this cost me $30 bucks and that's only because I had to buy a drill and stuff.
@KeepOnJeepinOn7 жыл бұрын
yeah it's always better to do it yourself lol people always like my skateboard wheel sliders
@MotardSteve7 жыл бұрын
MotoJeeper Yeah I gotta get some of those DIY skateboard sliders as well.
@KeepOnJeepinOn7 жыл бұрын
Do it! lol
@JeBehaardeOma6 жыл бұрын
You do know the drill your using is for Walls and stone materiaal right ??? Haha anyway like your vids about the 701 !! Keep it up
@MotardSteve6 жыл бұрын
+JeBehaardeOma Haha yeah my buddy pointed that out instantly lolol. I got Masonry bits. I was clueless 😂
@motohikinbc96417 жыл бұрын
Great mod! Funny you kept the plate covered during install then let her rip, hehe
@MotardSteve7 жыл бұрын
+MotoHikin'BC Yeah idk my brain had a weird moment with that. Covered it then was like "who cares" not like anyone can really do anything with the information.
@speezy14147 жыл бұрын
Nicely done gonna do the same to mine
@MotardSteve7 жыл бұрын
+MotoSteve it's still holding strong too. Even after looping the bike a week after doing it. 😂
@Spartan375X7 жыл бұрын
My fender eliminator kit: satellite dish brackets. Most of the holes lined up perfectly.
@MotardSteve7 жыл бұрын
+Spartan375x ha if it works, it works
@Spartan375X7 жыл бұрын
And way more solid.
@speezy14146 жыл бұрын
you literally skipped the hardest step..putting on that damn rear fender piece
@MotardSteve6 жыл бұрын
+MotoSteve it's not super hard, just gotta get it on there right. Once you're used to it, it's not bad
@speezy14146 жыл бұрын
And how did you put the rear bolts in above brake light
@MotardSteve6 жыл бұрын
+MotoSteve To be honest. I don't think I did. I'd have to look
@chinnchoppa88447 жыл бұрын
so much effort to block ur plate just to show it lol
@MotardSteve7 жыл бұрын
+chinn choppa what can I say. I realised hiding it was stupid in the first place.
@Izreal33457 жыл бұрын
Looks nice bro
@MotardSteve7 жыл бұрын
+Izreal 3345 Thanks man. Pretty happy with how it turned out.
@Izreal33457 жыл бұрын
Looks like some shit I would do instead of buying a $300 part
@MotardSteve7 жыл бұрын
Izreal 3345 Gotta save that green, especially when the exhaust I'm looking at is $563 but it's one of them fancy SC Project ones. 😎