Anoth pump had a bad seal. this video shows how easy it is to rebuild the pump
Пікірлер: 176
@chuckgilbert2035 Жыл бұрын
Love it when a guy that makes a video comes back years later to answer peoples questions. That shows me who to subscribe to. Learn more from comments then a good video.
@andreowens49839 жыл бұрын
Thank you very much for taking the time to make this video. I was able to pull my pump apart and everything in mine looked almost exactly like in the video. saved me a lot of money!
@stucklikechucklookinlikewh95014 жыл бұрын
Thanks for the video🍺🍺. Exmark Lazer Z HP I blew out my right pump bottom seal. I opened the pump and the bearings in the swash plate was chewed up. I got all my parts from Jack’s Small Engine. I changed the bearing with the races, the top plate, & the bottom seal. I opened up the left pump, everything was good. I flushed all the lines, both drive motors, and the reservoir. It’s running good as new now. Thanks a million🙏🏿🙏🏿👍🏾
@aroldfut6 жыл бұрын
Good video with all the detail I need to rebuild mine on my Ferris. Thanks!
@andyyeager33813 жыл бұрын
Mines just like yours except I have dixon kodiakELS 60.. MY OIL filter hard to find until NAPA got it for me napa gold 1269. I'm ordering the whole hydro gear PG 10 cc. I think my pumps identical. Never fooled with hydrostats just hydraulic cylinders on tractors and a dozer. Your video was very helpful for me to see what I'm getting into. Thanks good job!
@andyyeager33813 жыл бұрын
Ordering the whole overhaul kit
@andyyeager33813 жыл бұрын
Ordering the whole overhaul kit
@diazaa9 жыл бұрын
Hydraulic Technician here. I would HIGHLY recommend to replace ALL seals while you have the pump disassembled! You can buy a speedy speedy seal that saves you from finding a hard to find shaft. Also clean each component! NEVER assemble with dirty parts as you are allowing contaminants into your new/rebuilt pump. The fittings should also be removed to replace the orings. Other than that, good job! (It would not hurt to lap the port plate, piston barrel, pistons if not replacing them).
@bradmcoy87062 жыл бұрын
Do you have any hydro rebuild videos?
@diazaa2 жыл бұрын
@@bradmcoy8706 sorry, I dont have any videos
@bobdriver69466 жыл бұрын
Rather than poke holes in my fingers with seal picks, I use a set of small external snap ring pliers to get that bottom clip off. The trick is to file a flat spot on the outside of the barrel on each side of the pliers. Squeeze and spread with the snap ring pliers and THEN run your pick under the clip. No bloodshed necessary. I've used vaseoline as assemble lube for years. It's cheap, works great, and I sometimes have to point to the large jar to subtly ndicate my opinion when negotiations are heavily skewed against me.
@kefabosire82810 жыл бұрын
Well done. Very clear illustration
@scratch16769 жыл бұрын
thanks for taking the time and making the video. I found it helpful.
@jesssharah74758 жыл бұрын
really educational and beneficial, now i know how a piston works
@quadmachine84344 ай бұрын
Perfect instructions!
@cereus577 жыл бұрын
great teardown on the pump!
@nasirazizkwt110 жыл бұрын
Good Work, but you should clean the pump from inside, outside and remove all the dust
@leonelgimenez54142 жыл бұрын
Gracias por compartir muy interesante todos sus vídeos
@mptaz12694 ай бұрын
Where can I find the parts for the pump rebuild? Thanks.
@fitzsfixes10 жыл бұрын
Realistically, if you take good care of the mower and do maintenance religiously. You can get thousands of hours on a pump. But if the mower is neglected at all, you're looking at under 2000 hrs. The price of a pump is around 5-600 depending on the mower As far as cost to have one rebuilt? I'm not sure. I'd have to imagine 3-400 though. To rebuild it myself, it was well under $200 Don't be afraid to tear into one. They're way less complex than they look. Just make sure you put it back together in the same order you took it apart.
@andyyeager33813 жыл бұрын
Extreme heat and hot weather can do harm to any equipment no matter how much u baby it. Extreme heat breaks down the viscosity in oil. Grew up on farm and around heavy equipment.
@fitzsfixes3 жыл бұрын
@@andyyeager3381 Completely agree. What I'm saying is those that let grass and grease build up on their pumps will need to replace them sooner
@andyyeager33813 жыл бұрын
Abuse and neglect can do a lot of damage so your correct on that. I watch these videos of these young kids working for excavation companies that will dance these skid steers on 2 wheels and twirl around to show off but I never see the boss or owner make the little punks pay for the expensive repairs it creates and im sure u know what I'm talking about.
@andyyeager33813 жыл бұрын
I found a kit for 160 so I'll rebuild it myself. I've been a backyard so called mechanic all my life rebuilt Holley 750 and a couple quadrojets back in my teens I'm close to 60 now. Did HVAC for 25 years u learn a lot in that time and still learning like now.
@ricardoflak19345 ай бұрын
Super nice video! thanks for sharing ! Do you know part number for the top seal just below the fan ?
@rfedist11 жыл бұрын
Awesome video. If you are ever interested in brand new pumps, give us a try. OEM surplus, less than dealer cost.
@reggiem1668Ай бұрын
Thanks for the video! I’ve got a Ferris IS 2000Z. I got my pump out then kinda lost my nerve to try and tear it apart. Was planning to take it somewhere until I found your video. I believe I can handle it! 1 question…My right pump has just developed the leak but the left wheel has been sluggish for quite a while. Only notice when reversing that side, especially if the front wheels are angled a little wrong. Any ideas what might be causing this? Hoping it’s not a wheel motor!
@jusjerry21611 жыл бұрын
Good video! Answered all the questions I had and some I didn't
@fitzsfixes11 жыл бұрын
There's a ton of places online. I just picked one close to save on shipping.
@laraeverble-whitaker5077 жыл бұрын
Thanks so much, very informative
@keithpack74368 жыл бұрын
Thanks for the video. I have the same machine. very helpful
@rayaratkon1654 Жыл бұрын
Hi, good videos how to put neutral manually on that zero turn?
@lawncare976 ай бұрын
I have a exmark front runner. My dust shield is stuck on. How do I get it off to get apart?
@bradf916811 жыл бұрын
Hey very nice job , great detail , especially with the "little guys and pops off" nothing left out to guess at ............................I was wondering if the seal could be changed without disassembly , always good to inspect for internal problems as well though
@moverabcАй бұрын
thank you for this vidieo
@johnstephens98535 жыл бұрын
I would advise the first thing is to clean the pump up first before yo0u take it apartand provide a clean work place PREVENT FUTURE DAMAGE.
@Dmax042 жыл бұрын
My Cub Cadet M60 Tank has the same pumps. On mine the lower bearing was wore and let the shaft wobble enough to take out the seal. Oil dripped on the drive belt and the mower wouldnt move. My pump did not have the wear plate like yours. The pulley on the bottom is a tapered fit and man it was tight. Ended up ruining it trying to get it off. I figured maybe $20.00 for the pulley. Wrong!! It was $63.00. With the pulley and bearings and seals and new hyd filter and a new belt it ended up being around $200 to rebuild vs around $600 for a new pump.
@ryansaunders2913 ай бұрын
What is the ball and spring I lost mine and need to know what they are to get new ones
@jamesconnell58763 жыл бұрын
Super video! Thanks !
@MekazaBitrusty10 жыл бұрын
Thank you for sharing. Your video work did give me a bit of a head spin though. :-)
@oldkicker89586 ай бұрын
You mentioned that one time you installed the charge pump cover 180 deg. Dit it not do anything at all, I’ve been trying to track down a relief valve, litte plastic ball so decided to make one with a 5/16 steel ball bearing and a spring fro an ink pen. Do you think this could work ok?
@graveyardrumblers8 жыл бұрын
I believe this rebuild is the same pump on a machine I own... its a hydro gear model number 5102174YT... if you could, it would save me alot of time if you can provide me with the part numbers of the components needed to rebuild this pump. If I am incorrect and this is not the same pump, where is the best place to go to find bearings, seals, vanes, etc. etc. thanks, mike
@just1lifexx118 жыл бұрын
yoou have good camera..
@TheSimpleFighters6 жыл бұрын
Where did you buy this Rebuild kit?
@Comanche3Six10 жыл бұрын
Very informative, Thanks!
@n9878f11 жыл бұрын
Nice video... Where do you order those pump parts from?
@thomasshirley50465 жыл бұрын
Lol but i need 2 hands so stand by i laughed so hard damn your a good teacher thank you for the excellent video great pointers
@Anthony-ir8dy9 жыл бұрын
Thanks for the video. Man, are there some idiots that commented!
@alfredonegroni55587 жыл бұрын
Thank you for show me you repair the pump can you tell me where you buy the kit for repair I have the same problem al living in Puerto Rico thank you
@timelliott6864 жыл бұрын
I have 2004 dixon ztr 1950 and can't find parts mine looks similar to yours with no fan and having difficulty pulling bottom pulley off
@paoloodar67244 жыл бұрын
hello my name is paolo my question is what puefo tools take out the hydraulic pulley of my ferris thanks
@robertneese296 жыл бұрын
I have a question. I have a zero turn and it jerks and stops pulling on one side at times. Is it going to be the pump or the drive motor and where can I get Parts to rebuild one or both. Thanks. Robert.
@danielaustin11473 жыл бұрын
How do you take the piece off under the fan? Once the fan comes off I can’t get the round sliver thing off
@JM-yx1lm2 жыл бұрын
@ 2:28 where that charge relief ball is you are missing the spring I didn't see it on the cover either
@JM-yx1lm2 жыл бұрын
Dadgum it ! It was in the cover! Good job pointing that out to people
@dennisiverson30477 жыл бұрын
I have a 1970's clark 630 bobcat having drive slipping problem the hydrostattic pump?
@user-md7cs9yr2s4 жыл бұрын
In the charge cover is a flat gasket, do you replace it with the flat ring gasket from the overhaul seal kit? It is smaller (need to be stretched a little) but flat and there are three o rings that would fit. Thanks for your help!
@tech27015410 жыл бұрын
what is the average price they would charge to rebuilt a hydro pump of lawn tractor thanks
@brianfitzpatrick91895 жыл бұрын
Great video. Thanks Can you rebuild walker mowers hydro?
@Glideman053 жыл бұрын
On exmark lazer z, does the pulley have5o be removed before you can pull the pump?
@martyrogalinski63837 жыл бұрын
rplaced hydrostatic pump, unit doesnt drive straight, how di yiu adjust ?
@fitzsfixes9 жыл бұрын
Between the bearing and the seal, is the flat washer. The c clip holds it all into the housing. What did you tighten? And how in the world did the housing break?
@giantsean6 жыл бұрын
Hi.. just bought a secondhand Scag Wildcat which seemed to be in pristine shape. Got it home and of course it leaks :( It appears to be coming from the union of the top and bottom "halves" (quotes because I know the bottom is longer). I am hoping it's not the shaft seal because I'd hate to have to pull the whole thing apart already, but I noticed you didn't change the case seal. Do those tend to go bad, and/or is there any other special reason mine might be leaking from there? It did get bounced around a bit on the ride home, but nothing I wouldn't expect from regular work. Thanks!
@alejg20083 жыл бұрын
On 1:02 how do you remove that top plate that goes on top of the shaft??
@sutterkramer25486 жыл бұрын
Is that a bearing that fits into the fan so it can be mounted to the shaft or what is that?
@JustKipp3 ай бұрын
Can you do a video on removing the pulley? Please 😮💨👊
@fitzsfixes3 ай бұрын
It's an 11 year old video. That mower is long gone. Sorry
@JustKipp3 ай бұрын
@@fitzsfixes Right on, just trying to avoid buying a pulley remover. 👍👍
@noelleonard24982 жыл бұрын
Aren't you contaminating your hydraulic oil with regular oil by lubing the pump up on assembly?
@LaBargeMedia12 жыл бұрын
Mobile 1 15 50 is the hydraulic oil used in the machine. That's what the owner's manual tells you to use
@johnhugon83052 жыл бұрын
Can you turn the valve body 180° to make the wheel motor hydraulic hoses point to a different direction?
@JM-yx1lm2 жыл бұрын
It will rotate only 180* but yes. Otherwise your forward and reverse will be backwards.
@hoplahey9 жыл бұрын
What does the ball and spring do? Is it a safety valve or something?
@sofrits28 жыл бұрын
What was the part number for that first seal (directly under the fan) you had already replaced prior to the video?
@blackhawkdown26662 жыл бұрын
Yeah I like to know also mine is leaking right there
@garyrowlands85379 жыл бұрын
Hey , this is really good information, but could you please move the camera less, thanks :)
@dustinmc226 жыл бұрын
Got the nut off the pull but it won't come off!! Any tips?
@lisaok47299 жыл бұрын
I have a Husqvarna CZ4817 zero turn riding mower that I just replaced the drive belt and ty-rod. It worked fine for 12 hours of mowing (4 different times). I was mowing last night, went to use the right arm to back up and it would barely move backwards. It moves forward just fine and turns just fine. It just want back up on the right side. Left side works fine in all directions. Please ya’ll any ideas on what to look for, where do I start? Thank you so much in advance.
@fitzsfixes9 жыл бұрын
Sounds like the drive belt again. I don't know why you would be going through them so fast. But that's what it sounds like to me.
@buzzjones49584 жыл бұрын
Great video. Can you post the parts list?
@fitzsfixes4 жыл бұрын
Sorry. This video is from 2013. The place I got the parts from has been out of business for a few years now. I dont remember any of the part numbers. Try Googling the parts you need. I'm sure some place has what you need
@rogeliosaavedra59705 жыл бұрын
Will worn out hydro pumps cause a mower to go not go as fast when mowing? I have a cub cadet zero turn (The Tank), and I notice it struggles to turn around. It doesn't go fast when going forward or backwards. Thanks.
@fitzsfixes5 жыл бұрын
You check the belt? If its loose or worn out, it'll do that
@donniecorrigan85192 жыл бұрын
Hi Great video, is this the same pump rebuild procedure as on a Gravely Hydro- Gear , it is whining & after it gets warm it slows to a stop, no leaks though.
@JM-yx1lm2 жыл бұрын
Yes. Exactly the same. Some have the plate like this video and some don't. If not you have to buy a new end cap
@davenolan50110 жыл бұрын
Great video I need to find out if I can buy a rebuild kit for a pump on my zero cub . I'm hearing there's not a kit and the pump is $450 but I really think if I tear it down I can get the parts from the big hyd shop up town . The wheel motor also may need rebuilt or replaced and maybe there's a kit for this as well Thanks for the video
@fitzsfixes10 жыл бұрын
When you pull the pump, take a look at the numbers on it. A quick google search and you might get lucky. A lot of other mowers use the same parts. You might find a place that has everything you need. Good luck
@andyyeager33813 жыл бұрын
Did u try MTD site?
@paulalbert825811 жыл бұрын
Your my hero!!!!
@dogerkarlstrom56764 жыл бұрын
Hello, im gonna buy a Simplicity 20 year 2007 with only 434 hours on it, but it is something wrong with it when it gets warm it gets slow with low power from booth wheels, i think the previous owner have tried to change oil and filter and also belts, what can cause booth sides to go bad?, seams strange?
@andyyeager33813 жыл бұрын
Oil weight maybe
@pro2pickr4116 жыл бұрын
Enjoy your videos! Question regarding the Ferris in this video - When replacing hoses, do they line up the same on both sides on the pumps? In other words, does the hose with the 90 degree fitting on the bottom of the wheel motor go into the left side port (looking from rear) on both or are they reversed? The Ferris parts manual shows they are reversed, but my mower has one wheel going forward and the other going in reverse following the diagram!
@oldkicker89586 ай бұрын
Same question here, I installed them both lower to the left fitting as your standing at the rear of the mower and the left wheel spun in reverse so I switched them and the left now the machine works as it should. Standing behind the mower the right side hoses are lower hose to the left port at the head and the upper hose to the right side port. I have a Simplicity and their diagram shows the opposite. So the way they have it is lower left on each side which didn’t work in my case.
@spk84748 жыл бұрын
Hi can i get your help me i have a hydraulic 52 inch lesco lawn mower and both sides of mine was making a sound but now it will barely even roll is it the hydraulic pumps or the wheel motors ? I took a look inside one of the hydraulic pumps it looks like nothing was bad inside and was clean ?
@fitzsfixes8 жыл бұрын
it's probably the lumps. but for both of them to fail at exactly the same time is suspect. are you sure you are full of fluid? if it's low, the pumps will whine and not move.
@dogerkarlstrom56764 жыл бұрын
if the valve plates is worn in the pumps, can this make them loose power?
@fitzsfixes4 жыл бұрын
Absolutely
@fitzsfixes11 жыл бұрын
Hey Bradley, I'll study the parts list for the next video! Hehe thanks for watching.
@esslamzahra507110 жыл бұрын
thank u very much
@michaeldumenkojr.82846 жыл бұрын
Can you tell me how to get the parts you replaced......like the seals, bearings and plate? I went to outdoor distributers & had no luck.....when I clicked on pg series pumps the link was dead. I need the part numbers & description .....GREAT VIDEO, thanx for making it!
@fitzsfixes6 жыл бұрын
Michael Dumenko Jr. I got everything from outdoor dist. So I don't know where else to look. Try Google searching the numbers mnaybe?
@michaeldumenkojr.82846 жыл бұрын
What numbers? Can you give me the part numbers....I would appreciate it.
@fitzsfixes6 жыл бұрын
Michael Dumenko Jr. Are you sure you have the same identical pump as mine? Take a look at your pump. The numbers are on the side. Google search those numbers and see what comes up. As far as my pump, this was filmed many years ago, and I have no idea whgat the numbers were.
@TheAlbundy33336 жыл бұрын
Jacks small engine website - look up ( PG-1GAB-DY1X-XXXX ) Parts Diagram
@trey29119 жыл бұрын
HOW CAN I FLUSH THE HYDRO ON MY EXMARK IT HAS GOTTEN WATER IN THERE SOME HOW I HAVE DRAIN IT AND PUT NEW OIL AND FILTER BUT STILL LOOKS LIKE IT HAS WATER IN IT ANY HELP THANKS
@fitzsfixes9 жыл бұрын
To do it properly, you should really pull them apart and clean the internals. If you want to do it quickly, take 1 of the 2 large hoses off the wheel motor. Take the end of that hose and put it in a bucket of clean oil. With you hands, spin the tire slowly in the direction that cases the hose to suck oil from the bucket. As you spin, the clean oil will cycle through both the wheel motor and hydro pump. The dirty oil will exet through the hole on the motor you pulled the hose from. After cycling a few quarts though, I would hook the hose back up and take the other one off and repeat the process, spinning the tire in the other direction. This will insure you have fresh clean oil throughout the entire system. Good luck
@fitzsfixes10 жыл бұрын
Yes it WAS a Ferris. I've since junked that mower. It was a piece of crap. Horrible cut.
@tech27015410 жыл бұрын
what is the life expectancy of a hydro pump under a normal use thanks for the nice vid.
@danielebrparish42715 жыл бұрын
2,000 hours
@brystonfranke16914 ай бұрын
Where did you get the parts? Or how did you find them?
@fitzsfixes4 ай бұрын
That was 11 years ago. The website I got them from has been shut down for years. Sorry
@brystonfranke16914 ай бұрын
@@fitzsfixes thanks anyways.
@fishman8010 жыл бұрын
i let someone borrow my log splitter. they added hydro fluid when it didnt need it. it was spewing fluid out of the relief hole but they kept splitting wood until the ram would no longer split the wood but it would go forward and back still, just no pressure on the wood. i realize it can be a lot of things but could this cause pump damage?
@fitzsfixes10 жыл бұрын
It's probably aerated. Do a fluid change and see if it fixes it
@fishman8010 жыл бұрын
123guinness thanks! I did a full fluid change and cycled it several times. I guess could be the pump.
@kevenc11 жыл бұрын
Great video! I've got an Exmark Lazer Z HP and one side is lacking power and responsiveness. I'm thinking it's the Hydro Gear BDP-10A pump. How do I know if it's the pump or the wheel motor? Thanks!
@ronaldnix6 жыл бұрын
good job
@sydpix2 жыл бұрын
Attempting to troubleshoot my IS 15000 Ferris. The movers left side lost power to the drive motor. The left side goes in reverse (enough to back it up) but almost nothing forward. In your opinion, would this be the motor or pump? Thanks
@fitzsfixes2 жыл бұрын
The pump only goes 1 direction. So it'll be your wheel motor that went bad.
@sydpix2 жыл бұрын
@@fitzsfixes - makes sense! Sometimes it just helps to bounce it off someone.
@sydpix2 жыл бұрын
Hey man, sorry to bother you. I just discovered my boy added straight hydrologic fluid to the reservoir not knowing the difference (frankly I don’t either). Shortly after that is when I lost power. Before I start throwing $2000 in parts on this thing. Is there a way to test either the pump or the motor to isolate the problem?
@sydpix2 жыл бұрын
By the way, when I put it on jack stands, the wheel moves both forward and backward. The pump sounds like it’s “straining” on the side in question. Thanks
@sydpix2 жыл бұрын
Welp, replaced the wheel motor. I think I bought the last one in the United States and same thing. Now at least I know it’s the hydro pump. May I ask where you bought your parts? I didn’t see anything in the description (mobile device)z. Thanks!
@gregballenger9168 жыл бұрын
Hey Fitz. Great video. Ill have to check out the rest of your productions. But for now I need some advice. I had just bought a grasshopper 721d G-2 1999 model and want to change hydraulic oil and filtwer. Grasshopper has their secret oil but I know its nothing special but I dont want to trash the motors. What would you recommend? Thanks. Great job. You have a new fan!
@fitzsfixes8 жыл бұрын
If they use what everyone else is using, get Mobil 1 15w50. But if they use something else, you're on your own.
@gregballenger9168 жыл бұрын
Alright Fitz. Thanx. I'll do a little more research.
@fernandoesquivel717 жыл бұрын
hey i ha ariens zero turn that one wheel move faster than the other what could it be plz help
@M.Huling4 жыл бұрын
Awesome
@corypollard80679 жыл бұрын
What is the name of the metal plate that got all grooved-up that you are replacing?
@krap1019 жыл бұрын
Cory Pollard port plate
@germanacosta91492 жыл бұрын
Hey buddy I need help can you help me?
@zavyz63645 жыл бұрын
Can you tell me where you got the new parts specifically the bearing
@fitzsfixes5 жыл бұрын
The store I got the parts from is out of business. The berings I got locally at "Buffalo Bearings Inc" Kenmore, NY
@BOWENS3578 жыл бұрын
Fitz' Where do you buy your parts at. I see you talked about buying the bearings for a little of nothing. Can you give me the name of the place online you buy your parts. I need a new bearing for the pump shaft. Your video is awesome. Thanks.
@fitzsfixes8 жыл бұрын
outdoordistributors.com
@BOWENS3578 жыл бұрын
Fitz's I called the outdoordistributors.com and they said they only sale the complete pump, but not the bearing by itself. Any other suggestion? Pump models. HYDRO GEAR PG-3KCC-NV1B-XXXX HYDRO GEAR PG-3HCC-NV1B-XXXX
@fitzsfixes8 жыл бұрын
+Ben Owens don't call them. Go to their website outdoordistributors.com and click on "lawnmower parts". Then click where it says "I don't my part number" then click on "pg sires pumps". A diagram of your pump will come up. Scroll down to the part number of the bearing you need. Then copy/paste or write down the number. Enter it into their search menu, and it'll show up. Or google that part number. And there'll be other places that sell it.
@BOWENS3578 жыл бұрын
Thx Fit'z was able to get the parts. A little clicking but all came out well. I just rebuilt one of the pumps and will go ahead and do the other one because of the lawn of one goes out the other one will. I have another question? I have the same pump in your video and ferris 1500Z. What type oil do you use in the system. You say in the video 15W/50. I am trying not to go the local dealer because they want to sell their oil. Looking to get it at the local parts store to save money. Do you use 15W/50 Synthetic? I am able to get the 15W50 and 20W50 systhetic at local parts store.
@fitzsfixes8 жыл бұрын
Great! I'm glad you were able to find the parts...Yes, I use Mobil 1 Synthetic 15W50. I use it in all mowers. new and old. Hope this helps
@fitzsfixes11 жыл бұрын
Now stop beating the crap out of it
@حسيناسماعيل-ج3ف7 жыл бұрын
thanks
@hendersondana119 жыл бұрын
what brand fluid are you putting back In the hydro pumps?
@fitzsfixes9 жыл бұрын
Mobil 1 15/50. I think they all use that now
@hendersondana119 жыл бұрын
Thanks I appreciate your quick response. great video!!
@luisivanrivera9 жыл бұрын
nice video but are the parts numbers
@fitzsfixes9 жыл бұрын
The pump is. Once you enter that, all the parts will be listed. I just entered the numbers in Google, and there were a bunch of places that sold parts.
@thomasponce8029 жыл бұрын
Did you have to bleed the system
@fitzsfixes9 жыл бұрын
Nope. Just fill the pump before installing. I filled it as I put it together
@tomahawkins10 жыл бұрын
What brand and model pump is this?
@NLCLandandSnow10 жыл бұрын
It's a Hydro Gear pump. Not sure on the numbers though. I've since scrapped that mower. Old and worn out. Horrible cut.
@Dusty39005 жыл бұрын
parts came from where???
@fitzsfixes5 жыл бұрын
No longer in business.
@Dusty39005 жыл бұрын
@@fitzsfixes Sorry to hear that...just busted open pump that destroyed thrust bearing and wash plate...went through both sides of case...can ya give me a point in a direction for spare parts?
@fitzsfixes5 жыл бұрын
@@Dusty3900 best bet is to Google the parts and see what comes up. I wish I could be more help.
@Dusty39005 жыл бұрын
@@fitzsfixes Thanks cuz ...ya still taught me sumthin...!
@bobhaggard84042 жыл бұрын
video jumped, did not show installing block, that is what I needed to know and you did not show...go figure
@charlottewilson49779 жыл бұрын
You are WRONG i put the washer and the seal on the bottom of the pump and when i tightened it down it broke my housing where the C ring is at, now i have to buy the housing, or should i say, when can i expect you to send me another housing, i liked your video, until, it cost me more money, now what would u like me to do?
@tu37128 жыл бұрын
How do you remove the pulley from a ferris. i need to fix the same seal you have here but cannot get the pulley off.
@fitzsfixes8 жыл бұрын
on the bottom of the pulley, there are 2 screws 10mm if I recall. pull them both out, and screw them into the other 2 holes next to where they came from. as you tighten them, it pushes the pulley off the pump. very easy
@tu37128 жыл бұрын
Thank you. I broke off the bolts since the hub wouldn't move. I will have to drill them out and try again.
@fitzsfixes8 жыл бұрын
+Jason Collier if they broke, you're fine. just grab 2 more and screw them in to the other holes. when the pulley comes off, your broken ones will be exposed, and you can grab them with vice grips once the pump is on the bench
@tu37128 жыл бұрын
+Fitz's Fixes the gasket in the kit I was sent from hydro for the top cover(4 10mm bolt cover) is round. The one I took off is a flat gasket. Does that matter or should I put the flat one back on? I appreciate your help.
@fitzsfixes8 жыл бұрын
+Jason Collier I re used the original gasket. No leaks at all