Hyundai Getz 2010 - How to Replace Bumper Rubber of Rear Shock Absorber

[@jvt3057]

Thank you so much man! I have searched whole KZbin to see how you remove the side panels in the trunk!

[@albertborrero2594]

Hi, Christian. Good DIY content. One detail though installing the bumper: insert one indent of the bumper inside the shock dust cover. Doing so the shock piston would be completely covered without the dust cover falling down along the shock tube. The piston rod shoudn't be exposed. Also the bumper would better serve its purpose to buffer metal to metal contact of the shock tube seal and dust cover during maximum compression of the shocks.

[@TheDlh69]

Thank you! Excellent video😊

[@timothynavarro152]

salamat po at meron nito! very helpful

[@Isaac21077]

You didn't need to remove everything, the little compartments on the sides have a little plastic part you pull out and gives access to the shocks.

[@jk_minion2446]

thank you very much for the video, it helped me✌️

[@jerickberdan764]

sir baka pwd ka din mag upload sir ng diy change oil ng getz and flushing ng fluids ☺️ thank you sir

[@di3d3monz]

There's actually a flap you can open and not have to remove the whole panel😁

[@di3d3monz]

At around minute 3.30 the side pockets....you can pull the first flap...and then youll see a square cover...remove that and you'll see the cover for absorber

[@christiannavarro7795]

@@di3d3monz Thanks for the tip. but that will be useful if i have the proper tools designed for it used by casa. This is just my DIY at home project using limited available tools only.

[@RrRr-th1kf]

Christian Navarro what is the benefit of this parts ??? Is it reduce damping and vibration????

[@dAndrei279]

@@christiannavarro7795 you don't need special tools. A flat screw driver for removing the square cap, a 17mm wrench and something to hold the end of the shock absorber. Doing so the removal of the shock absorber is much faster.

[@dAndrei279]

@@RrRr-th1kf this part is used to protect the shock absorber from dust and mud

[@insu3]

Ok, looks like very solid tutorial for DIY! I've started to replace shock absorbers + rubber with help of it, but... I was stopped by "other rubber". How do you detach those seals on side and back doors? (3:35 and 4:08) It is "pull me hard" technique?

[@insu3]

Ok, found it. It's "pull me gently, but firmly" technique. ;)

[@henreeyuma]

Upload kpa po more hyundai getz vids

[@christiannavarro7795]

Salamat po. Suggest po kayo ng pwede i-DIY.

[@TheWarriorHyzz]

can ushare the link of the bumber the defuser

[@hammerhead7344]

Do you have to buy the whole piece or just the yellow rubber??

[@MagicBox4u]

How to get these rubber for rear shock absorbers?

[@F.e.n.i.x13]

Greetings a help please, I have the packaging of the additional coolant broken and I want to replace it, according to the one I have has the replacement code is 25430-1C000, I would like to know if the container with the replacement code 25431-1C000, falls the same or works same in my hyundai getz 2008? Thanks in advance.

[@christiannavarro7795]

same

[@jasonpenequito233]

Sir yan din po ba dahilan pag sira na,kahit konting lubak lang maingay, kahit walang sakay sa likod..?

[@sainathkondbhar]

Thnaks

[@kaltengngaji4059]

Terimakasih ilmunya

[@gabrielemaninang3750]

Sir anu purpose nyan?sira na din kse sken

[@christiannavarro7795]

To minimize bumpy ride

[@caballover7937]

neişe yarıo o sünger

[@hishambadar]

Too much work... i would have just cut it open, slide in and tie with plenty of cable tie ... hahahaaa.... i am soo lazy!

[@christiannavarro7795]

Hahahaha