"I Machined a Forged Steel Sleeve That Didn't Fit the Lathe: Pre-Machining from 1050x720 to 1030x830

[@trialetcompagnie4481]

Big nice job 🤩🤩👀👀👌👏

[@hydraulicfactory]

Thanks bro 👍🤲

[@trialetcompagnie4481]

Nice job 🤩🤩👏

[@hydraulicfactory]

Thanks bro 👍

[@TOTOTRAZOM]

Très beau travail comme d'habitude, une belle équipe avec ces jeunes ouvriers, bravo et merci pour ces vidéos👍👍❤❤

[@hydraulicfactory]

Thanks for your nice comment brother.👍👍

[@Manufacturingzone-c1h]

Hello everyone have ha great day amazing video good luck ❤

[@hydraulicfactory]

Thanks bro 👍

[@bernardreilly7519]

Well done again. It would be of interest to see a short vidieo of your other machinery Bernard Glasgow Scotland.

[@hydraulicfactory]

Thanks bro, I will try to do it from my new workplace.

[@Tumbleweed2832]

Amazing Work.

[@hydraulicfactory]

👍👍

[@olegevstigneev5367]

Отличная работа.

[@hydraulicfactory]

Thanks bro 👍

[@OgiveBC]

Nice work, thank you for sharing.

[@hydraulicfactory]

Thanks bro, you're welcome

[@svobodnyichel]

Əla iş yapdın.👍👍👍👍

[@hydraulicfactory]

Teşekkürler kardeşim 👍

[@adnanduman9651]

Ustam kolay gelsin bol kazançlar 👏

[@hydraulicfactory]

Teşekkürler 👍👍

[@GulcanDuman-b3s]

İyi çalışmalar 💪

[@hydraulicfactory]

Teşekkürler 👍🤲

[@Gülözcnn]

İyi çalışmalar 👍🏻 yine çok güzel işçilik 👏🏻👏🏻👏🏻

[@hydraulicfactory]

Teşekkürler 👍👍

[@haloday9008]

Ooo myyy gooooddd 😮😮😮😮😮

[@hydraulicfactory]

Thanks bro 👍

[@OyundunySı]

İyi çalışmalar 💪🏼💪🏼👏🏻

[@hydraulicfactory]

Teşekkürler 👍

[@GulcanDuman-b3s]

Çok güzel işçilik bravo 👏

[@hydraulicfactory]

Teşekkürler 👍

[@AyşeTopcu-p2t]

👏👏👏👏👏👏

[@hydraulicfactory]

👍👍👍👍

[@benfranz5812]

Very impressive work. It looks as if the sleeve was 20-30 mm too large to clear the cross slide - can you swing a 1000 mm diameter part over the slide? The boring bar looked like it was sticking out about 2 meters. Did you have chatter that affected the surface finish?

[@hydraulicfactory]

It rotates up to 1010 diameter on the car and 1350 on the sled, there was vibration when taking the very end of the part, but in the last passes, there was no vibration with the thin shavings and I bedded the part and took the inside.

[@kezibanozcan9321]

👏👏👏

[@hydraulicfactory]

👍👍👍

[@NecatiŞafak-u2q]

👍👍👍

[@hydraulicfactory]

👍👍👍

[@subramanianmani2082]

super

[@hydraulicfactory]

Teşekkürler 👍

[@Ruhtamiri42]

Muhteşem👏🏻👏🏻👏🏻

[@hydraulicfactory]

Teşekkürler 👍

[@ÖmerDaşdemir-n1r]

Kolay gelsin ustammm

[@hydraulicfactory]

Teşekkürler 👍🤲

[@davidbrewer2929]

Where's your safety glasses knobs

[@hydraulicfactory]

👍👍

[@AyşeÇevik-m9b]

Kolay gelsin

[@hydraulicfactory]

Teşekkürler

[@OyundunySı]

Merhabalar usta 🫡

[@hydraulicfactory]

Merhaba 👍