I turn Washing Machine Motor into 220v electric Generator

[@kinghomemade]

*I make free Solar Stove* kzbin.info/www/bejne/eGOyhKKvf9Gom7Msi=S2QqahbFTV9_EkaR

[@palmyra2050]

What's with all the negative comments!!!! It's the principle that counts. Great to watch. Thanks 👍👍👍

[@BOREDANDWELLBORED]

There's no negative comments here I can see. But I can't figure out which one is the positive and negative out of the 3 wires in 8:43, maybe you can help me how he figured that out?

[@scaricraft3995]

@@BOREDANDWELLBORED This is a 3 fases motor, he will output 3 sinusoidal wawe whit 120 ° of difference.

[@BOREDANDWELLBORED]

@@scaricraft3995 but I can only connect 2 wires to plug it to appliances, which of the 2 wires out of the 3 do I use?

[@scaricraft3995]

@@BOREDANDWELLBORED this is why i think Is fake

[@scaricraft3995]

@@BOREDANDWELLBORED 1 Those magnets are too small and far away to generate something 2 the magnets are too far from the windings 3 if turning the axis by hand generates 240 V, connected to that motor it should have an output in the order of K volts 4 using a three-phase motor as a generator you get three-phase current, it should pass it on a three-phase DIODE BRIDGE to bring it to DC, filter it, adjust the voltages and then feed it into an alternator to have an alternating output 5 despite the increase in the carick, no device seems to be affected by it, including the engine itself.

[@NikNik3197]

Насос примерно 135 ватт, музыка 120-150 ватт, вентилятор около 35 ватт. итого около 300 ватт. 1.4 ампера примерно . кому интересно. генератор работает на пределе и скоро нагреется, следом из за нагрева магниты начнут терять свои свойства и ток упадет, дальше больше. А так для уроков физики очень даже наглядно сделано.

[@sergsmok7379]

А что бы не нагрелся потребление не должно превышать 150вт?

[@ВинниПух-у7и]

Походу показана ідея переробки. Балансіровки немає.ремінь гавно, перший здохне. Обично на генератори беруть трьохфазніки. 3-5квт.підключають врежимі генерації і мотор 4х тактний,економний

[@aymenben546]

Hgyt kkoplkoi nnjkbza jjjjbmmmpikkijjh

[@Дарханнахрад-п3и]

Я бы купил заводской движок. Это пустое затрата время.

[@sumonkushtia9415]

G g hgfhutg

[@neilbain8736]

Ingenious! I've used a drill as a lathe many times too. The issue is how accurate the job needs to be but you'd be surprised what you can do with just a file or wet and dry paper and a steady hand.

[@claydo364]

He Asian....no sturdy hand Hence grinder...it was only battery operated too🤣🤣🤣🤣🤣

[@williambear2402]

Thank you for not having loud horribly annoying music on your video to distract viewers from the fact that even if this worked it would be a colossal waste of time and resources.

[@robertelliott5644]

In stead of going through all that grinding, you could have used a drill bit the same diameter as the magnets, Measure the thickness to flush and drill down, Then place the magnest in each hole and mix a little bit of epoxy to secure them in place.

[@finddeniro]

Shirley...

[@0ChanMan]

I was thinking he could have just used a little starter current to induce some magnetism into the rotor while it was spinning and skip opening the motor up all together..

[@ИсинМанджиев]

В кустарных условиях очень даже неплохо, кроме сверлильного и шлифовочного ничего не заметил.🤔🤔

[@germangarcia9780]

Cual es el tamaño de los magnetos?

[@futures.scalper.808]

Rotating mass is less, more efficient to lighten rotator with epoxy.

[@arouno8905]

Great. You have created a Dynamo from a washing machine motor. That gave me an idea. Thanks for sharing. You can also use that on flowing streams or by the windmill. I am very grateful for your invention.

[@ZorlacSkater]

The motor is already a dynamo. He just tuned it basically. Each dynamo can be used as a motor and vice versa.

[@hamiltonshamley5785]

@@ZorlacSkater hi please could you tell me if this would actually really work?

[@sivam7536]

Wash motor has two main winding to rotate in both directions, no need to remove another winding wire, it work's as 2 phase with neutral alternator

[@muanahauhnar4938]

I will be more impressed if you running the motor by using free energy like Warterfall or something like that.. btw good job

[@rickhart6631]

That would be the next phase, you 1st is always to get an operating system.

[@hewhoenlightens5431]

I wish I learned more about this stuff sooner, but plan on learning how to utilize electrical equipment from many angles! Few good videos on JONLEVI & others dealing with old world tech & free energy! Someone with more understanding might help shed LIGHT on this stuff further! ✌💎❤

[@kt-limbo]

Maybe some source of wind

[@srilankans]

wash machine motor in to a sanding machine. kzbin.info/www/bejne/mGTbqn-KjrulmMk

[@rajkumarraj3711]

@@rickhart6631 1I

[@lukedias1988]

6000 watts is a bit ambitious. The generator is probably producing around 500 to 600 watts at most. You can see it struggle to produce sufficient energy with the fan blades slowing down.

[@Village_lifestyle_vlogs]

Secondly although magnetic field in rotor is increased but wires in winding are not enough in motor to produce the this much power.

[@ronniewebb2979]

Just my opinion on the fan. It may be a optical illusion made by the camera recording the video that makes the fan appear to be slowing down. Like for instance, videos of single or double engine plans and it appears as though the blades are not even turning because of the fps recording speed.. Just a thought....

[@Village_lifestyle_vlogs]

@@ronniewebb2979 you are right. But here have to think simply 6000w means a generator of 8hp, is it feasible that a generator made from 300w motor can produce so much load. If on modification we suppose it may produce , double or triple means 900w, only for a little time span not for long hours. But not 8hp. And load on it assume 70w fan+ 300w speakers + pump 325w. But not 6000w.

[@Meop79]

@@Village_lifestyle_vlogs probably 600w, 6k watt being a typo...

[@Village_lifestyle_vlogs]

@@Meop79right ✅

[@drewrinker2071]

Thank you, i have a wash machine motor i actually wanted to use for this purpose but because they are inductive, normally you can't use them as a generator. But with your method you can. Genius hack. One suggestion i might make though to make it a little easier is to use a thick cardboard tube or maybe even water bottle the right size instead of pvc for easier removal once the a+b hardens. And as someone else mentioned, what is the actually frequency that this is, I'm guessing that it changes with the rpms of the engine. the frequency of that generator could therotically be bad for some electronics, if it is mismatched, so it would be good idea to run the power that it produces into a charge controller with battery bank and then invert it to the right voltage and frequency that you need.

[@gordonbeaton8131]

Seems pointless as a lot of machinery dislikes inverter power as often not pure sine wave, it is expensive to make it sine wave, so perhaps what you could do is get an old alternator from a car and charge batteries from that! This produces 220-250vAC pure sine wave you could build a frequency control that keps the revs and voltage correct

[@elsindo]

See.. The inventor just busy to pin his/her latest video instead of give us a very brief answer about that frequency thing. So I hardly think it's legit.

[@drewrinker2071]

@@gordonbeaton8131 yes i think your right a lot of cheap inverters tend to " burn up" electronics as i have found out the hard way. But things like a fan or old television as shown here. No big deal if it burns up. I wouldn't want to plug anything expensive in this

[@claydo364]

A breaka switch boys...

[@joelelloreg26]

You should put volt and amp meter to prove it will sustain enough power to the load. Not convincing without it.

[@РафикТалипов]

мощность генератора на порядок выше мощности привода. Если инвертировать, может потянул бы музыку. Тем более откусили одну фазу.

[@erastusnjenga2097]

Amazing and creativity with proven results blessings

[@psh951]

Did anyone else notice that he has his speaker plugged into a power source through the positive and negative terminals to the speaker!!!!!! Apparently I guess his generators a musical amplifier as well!

[@Forte89]

Obviously its plugged in to power the Bluetooth which feeds into the speaker

[@arthurcombs5032]

@@Forte89 Thanks for keeping me from having to tell him. 🍻

[@chrislittleton6908]

Would love to do this and hook it up to a windmill and batteries to power a pump to keep a stock tank full.

[@tuvoca825]

Treadmill motors also work.

[@albertoleecarranza9477]

So do ceiling fans.

[@tameemjamal5505]

It would have been even more apt if you used wind to turn generator ! Great job nontheless

[@swearick]

Probably wouldn’t have worked the same. For a couple reason. Wind won’t spin that generator as fast or as consistent as the gas generator. That’s why you often use home wind generators for charging batteries as it is lower voltage and doesn’t have to be consistent. Your voltage would be all over the place otherwise.

[@joesinventions.6626]

What about petrol should use commutator

[@shaynegadsden]

Yeah using wind for a direct ac generator is near impossible you really need a constant rpm of about 3000 for that thing

[@dhirendrapsingh6758]

Informative. Useful. Calming. Inspiring. Life-changing. Enjoyable. Heart-warming. Other.

[@СтаниславЯницкий-ш3о]

Why not use an energized winding? Small battery and generation efficiency will greatly increase. When operating on a load close to the maximum power of the generator, it will inevitably begin to heat up strongly, in addition to the fact that it will need forced cooling, the magnets proposed in this design lose their strength when heated, which is why they are almost never used in industrial solutions.

[@jekichandra4921]

Gak mungkin

[@gumpamai]

@@jekichandra4921 mungkin

[@GusBendjol]

@@gumpamai indonesia gak jelas. 😂😂😂

[@moestrei]

Many electric motors use permenent magnets, from toy motors to electric trucks.

[@patricioromero3956]

@@moestrei neodymium magnets works up to 150ºC if i recall correctly it also depends on the composition of rare earth used.

[@yvonrouillard9755]

Now you need a regulator to have a stable voltage

[@tomashareru5460]

I apricet you

[@jeffriegerry3523]

Smart... and simple.... this guys very smart..

[@ramadaneel8048]

Not everybody's cup of tea. Innovative ideas of recycling and use of electromagnetism. Worth watching.

[@henrywilliams1439]

The pulley on the motor/generator is twice the diameter as the one on the gas engine. If you switch the pulleys you will get 4 times more speed and thereby produce 4 times more electricity.

[@Now_lets_get_this_straight]

maybe it needs the torque

[@metatechnologist]

It's usually not that easy.

[@SrIrv]

More power may not necessarily be a better result in this case. Remember that you have to not only control the total voltage but keep it at the required frequency(notice how slow the fan is moving?). Great job overall.

[@henrywilliams1439]

@@SrIrv When I said more power, I meant more electric power; I changed it on my comment. A larger pulley actually has less *mechanical* power because of less torque. The bigger the drive pulley the more generator speed, but less torque. The gas engine has plenty of torque, so that won't be a problem here. When the drive pulley is larger than the generator pulley it spins the generator at a faster speed than the driver rpm; that's why people use a 24" bicycle wheel to turn an alternator with a 2" pulley(12 times faster); more generator speed means more electric output up to a certain point. The frequency is how fast the current changes direction, so the faster the rpm, the higher the frequency. When studying electronics, it's said a higher frequency always means more electricity. Switching pulleys would give him 4 times more speed. The fan runs so slow because his set-up is only producing about 2 amps or less, that's why I said he would get better results if he switched the pulleys. (The monitor of this page doesn't think switching pulley's would be better, that's why he Highlight's any opposing reply to my comments.)

[@brianfretwell3886]

@@henrywilliams1439 Would you get more power or just higher voltage which would slow or stall the engine if too high a current were taken.

[@AbuBakar-px5oz]

yes this can generates some small power..10:16 but impossible with just hand rotation to generates 240v...don't fool people.. and the resin will melt, better drill a hole for magnet sitting flush with the rotor..

[@williamesselman3102]

Yes, but the idea that I can create a generator and use a large wind rotor and gear it down to increase the speed of a smaller spindle means I can generate electricity in my yard. I can Rectify it and store it in batteries.

[@TriPham-xd9wk]

Any motor wire l like that with magnet in the rotor and wired coil in the stator can be used as generator

[@furypcgamer]

Yes

[@زعترزعتر-ه7ن]

هاي صح لو غلط

[@TheHeydax]

Yes this is Bullshit

[@nelsonmtb809]

60 frames per second makes everything looks like in slow motion. Great video!

[@proaz4034]

i think if you use bicycle as source of power will be great ! sport and energy

[@Anomaly.Filmworks]

Yes! Wire it to a charging circuit and charge some deep cycle batteries.

[@danielgreylingrevealedtrut9469]

Brilliant , just a fee tweaks and its masterful. You are very talented. Share more please.

[@justinromang9113]

I like Your "NAME" ---- "ONE *T R U T H* " . W I S D O M G U I D A N C E S T R E N G T H S H I E L D *A M E N*

[@danielgreylingrevealedtrut9469]

@@justinromang9113 Am about to start a series of the contradiction's and truths spoken of in the bible.

[@justinromang9113]

@@danielgreylingrevealedtrut9469 ..love IT .. We shall comunicate; I`m too buisy, at The Moment. The Best - 4 ALL . LOVE Justin.

[@PedroRamirez-sv5iu]

Si Dios te bendigas mas por compartir tu valioso talento con los que no sabemos nada hno.

[@giovannifasulo8426]

Beautiful, but there is a problem: the current delivered is not at 50 Hz. Therefore, using this current will break the objects.

[@jamesnash6101]

Are you sure that it will break the object? And how do you know?

[@themadscientist5025]

@@jamesnash6101 Yea its not smooth current.... the Hz matters lower may be ok but higher will fry equipment .. just like in welding frequency..

[@pepenguyen5321]

@@jamesnash6101 yeah he need inverter for that but sadly he dont have one i guess.

[@pepenguyen5321]

@@themadscientist5025 yahh.he needs battery then inverter

[@hamidshaikh8638]

Very nice washing machine motor used for 220 volt

[@mrlondon963]

Good idea. But you're giving it lots of energy to get the 240v out, why not try to connect it to a windmill of some sort.

[@gyfqrtt556]

Idea

[@jasonclark6194]

Windmills won't give enough speed or constant speed to keep a steady voltage. Windmills are good for charging battery banks.

[@Gsavell]

Bravo becarefull the energy company coming after you now you know how to organise and create electron flow. I thought that motor was a 3 pole/winding when you cut the blue I was 😖. The fact you moded the rota like you did show engineering skills. Now build either a water wheel or wind turbine so you can get it for free!!!

[@soundwave6218]

😶

[@marketermagic4993]

lol this guy is a genius,thats a million dollar idea

[@dfsilversurfer]

You know what impressed me 1st? Just how new and clean looking his drill press and all the other tools and bits and pieces were . Then how his hands are not what I'd expect from someone who does these projects. Too clean no scrapes ,cuts etc.. so before I even seen his project something didn't add up. So before praising this young guys project

[@zhirayrsimonyan4977]

The idea is good,but this generator does not support the stability of the voltage of 220 V and the frequency of 50-60 Hz . The author must connect a Voltage and Frequency stabilizer after the generator.

[@broccolixxx]

Agree.

[@rodmills4071]

Covers himself in water and stands in water then plugs in to home made genny...... other than that good job. 🤣😂😁😀😎

[@ololoololo6631]

unlike mains, generator is insulated from the ground

[@ericscaillet2232]

Just testing the insulation....

[@ranaweerasilwa5228]

@@ololoololo6631 ppppp

[@ranaweerasilwa5228]

@@ololoololo6631 0000

[@Mavuika-115.3]

That's amazing! one of the best creations I've ever seen. Who would've thought you can turn a washing machine motor to a generator?

[@SurleyBlaine]

I have no idea why the new magnets and epoxy are used. Every other on I've seen usually just re-wire them with same results.

[@56_seshadrib71]

@@SurleyBlaine Do u know how to convert this 220 volt motor to dc without using such things?

[@jrambo7495]

This is fake,guys!!

[@bleehole]

@@jrambo7495 Do you not know how electricity is produced?

[@TageMHall]

@@bleehole NOT The Way This Guy Tries to Convince Us ...

[@hermantuinstra118]

Brilliant and good use of old motors which would've been discarded.😊

[@eleenchinoy407]

Using gas generator to run 110v motor to generate 220v is an expensive idea.

[@dopeweed8663]

It's actually a whipper snipper motor

[@Lloyd33]

@@dopeweed8663 a wut? o.0

[@rupeshpatel8002]

It will work 1000000% even more voltage depend on RPM only wind,water,bysycle,any fule, energy conversion.

[@daveridlespriger3040]

I turned a waiting room into a PRISON 🍩👆🤪. the similarities are unmistakable

[@TheHandsOnChannel]

That's an interesting way to wire your speaker. You had me going there for a minute lol.

[@peterpaulanunciado5643]

Lmao thanks bro xD

[@ne_alakao0]

جي😎

[@sensor1761]

toll das dieser Generator auch direkt an die Lautsprecherklemmen angeschlossen wird und dann auch noch Musik spielt :-)

[@schnakenschreck]

🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣🤣 In der Box ist Akku und Wechselrichter !!!!

[@AndrzejLondyn]

Thank you, very inspirational. I always wanted to be a mechanic, electrician like my father but finally I became an accountant.

[@subhankarmandol6083]

Same thing happens to me bro.

[@perentee77]

Same thing didn't happen to me..

[@thanhphuhoaivo9347]

Gia bao nhieu.co giao hàng ko

[@seanmcneill8899]

Some things don't add up in life.

[@Guy-ky9mc]

Good job. However I'm not certain that this particular configuration could produce 6000watts. Not with that little engine anyway. Regardless, very neat!

[@CabalisOrder]

The Bass is over 9000 Watts

[@skh4n153]

Book 9000w one for me. Dm me the price

[@sammyd7857]

He is just scamming likes and views

[@shaynegadsden]

600w would be a more realistic figure

[@arnbon6241]

A generator is actually a motor but used in reverse!. So in other words, a 1000w motor used as a generator cannot produce more than 1000w of output electricity. So to produce a 6kw generator , you have to have a 6kw motor (assuming a 100% efficiency).

[@salvatoresaccoccio2379]

No fancy tools or presses! Great work, thank you for sharing.

[@niks8085]

Чисто случайно оказался на канале по чисто гипотетической наводке одного человека , достойный "собрат" полуляха, канал по умолчанию держит планку 250/250 сами знаете чего

[@rayraycthree5784]

How many poles were in the field windings? Even if the right number for the number of magnets, the magnet position didn't seem to be too precise. Were the pulleys the right ratio for 50 hz? Would be interesting to put scope on voltage, audio equipment usually likes clean ac voltage.

[@MittyNuke1]

Even if the engine speed was controlled to make 50 hz, the voltage wouldn’t be controllable without changing the frequency since this is a permanent magnet generator (no control of field strength). I’m not knocking the project, it’s a cool idea, but this wouldn’t be suitable for utility power except for devices which can handle variability in voltage and frequency. Curious if the speaker was just a prop here, or if it has an internal power supply. Best option for a PMG is to rectify the power into DC and use an inverter if AC power if needed.

[@vivendoaprendendo2023]

it doesn't seem to be all that functional, it's hard to believe it actually works with so many working devices!

[@dedelenantais]

Should be possible up to about 5 or 8 A max. Looking at the diameter of the wire (maybe 1.5 mm²) you can't get a powerful generator.

[@bongaguilar7623]

Working with an unknown frequency is lethal to any device

[@dedelenantais]

@@bongaguilar7623 yes, indeed.

[@احمدعبدالله-ذ5ن8ن]

@@bongaguilar7623 اذا كانت سرعة الدوران ثابته فأن الناتج كذلك يكون ثابت اما كلما ذادت سرعة الدوران او نقصت يحل تذبذب ويضر بالاجهزه

[@sobrelaroca2701]

I Dont understeand but YEAH youre right man

[@drinkingjack5462]

I would really like to see you do this without the speaker connected! I have a feeling it is back feeding power to the fan and the pump?!! Maybe a hidden inverter?

[@ericksudrajat4608]

kalau pakai inverter di mana dia letakan.. apakah anda tak melihat cara buatnya yang sangat transparan..?

[@rajkor5764]

Petroleum generators are NOT good or necessary use Magnets neodium glued on a side of a disc with 2 oposite magnets near to sides produces spinn.. there are different prototypes on You Tube look it up.

[@joes5669]

Agreed. 100% fake.

[@trxtech3010]

That buried exstenion cord is pretty cool trick to get power further out...

[@sohailsaahb6764]

Good very very good tremendous Mashallah MashaAllah greetings

[@kinghomemade]

Thank you very much

[@tarachandbhati3935]

It's only max.500watt not 6000 whatt

[@esaboyak9226]

Hou about volt?what volt have sir

[@mrt528]

Good idea! I’m sure it’s not running the speaker, it’s running the fan and pump only

[@bhimraotembhurne6603]

The 0

[@bhimraotembhurne6603]

Ñms1111

[@bhimraotembhurne6603]

XßàÀ

[@alexb2.059]

Good sound even without amplifier 😂😂😂😂

[@albertopantig9248]

😄😄😄😄

[@jiangchang6757]

Yes, it is very good to turn waste into treasure. For the safety of reuse, thermal protectors can be installed on the transformer. Dual protection makes it safer.

[@mahdsaed]

I think the magnet poles should have been fixed parallel to the axis of the rotor. Not perpendicular to it, for the magnetic field generated to match the copper coil around

[@dwwilliams19732013]

That's not the only problem. How did the 120V fan and stereo work and NOT immediately get fried from double their working voltage?

[@ppfcreation]

If you use 2R radius of Rolar in oil engines then u will able to generate double of electrical energy through moter 👍😀

[@tuvoca825]

?

[@davidreynolds4684]

That motor looks like new. Came apart like it had either been torn down allready or it was very new.

[@claydo364]

Of course itll work friction magnetic force which in aid causes spark

[@Aleksandr_I79]

😂кто от доктора?

[@Whymewhynot-ok9fw]

Please bring lawyer as well

[@Вадим-м1о2я]

Я)

[@miguelm203]

you have a made a few mistakes: 1) what you have there is like a magneto and the output frequency and voltage VARIES directly with the rotational speed of the shaft (wich is not controller at all). the speed of the shaft should be 3000 rpm to get 50 Hz with two poles, since rpm = 120.f /number of poles. 2) the voltage reading you made was turning the saft with your hand and not with the gasoline engine... and also the value is incorrect! the highest voltage was 175 V RMS (at unknow frequency at minute 10:15 ). 3) you should check the voltage when the gasoline engine is attached and working. finally, i recommend you to use a green source of motion (instead of the 2 stroke gasoline engine) for the shaft, like wind or water from a river... and more important, learn how to read an analog multimeter here: watch?v=9rGDx92McTY

[@titianmapan8032]

Wow.. Thanks for the theory.. We go to the basic engineering system

[@lifeisgood3386]

I like the way he connected the fan up with what looked Like wet hands did not see him dry them off 🤣🤣

[@patbreslin5793]

He wiped them on polyester shorts, and was still trying to dry them on his T-shirt in between plugging in and switching on each appliance. I daresay he may be self taught. Admirable all the same.

[@sabrinaaliyarosyidah4843]

Ini bener 2 ide yang breliant patut diacungi jempol patut didukung dan dikembangkan bravo

[@nes-artnes-art3013]

And it still runs on PETROL. This means that you are dependent on the system.

[@727skirk]

replace gas motor with water turbine... sillly

[@jesusfeliciano5543]

Much respect my brother It is amazing what you're doing and sharing your talents to the world and I admire you for this

[@Trentmatthews]

He's a BS artist. If you know anything about electrical engineering, you would realize this entire video is fake. What he's doing does not create any power whatsoever.

[@РоманДудников-к9п]

Как говаривал Доктор Дью :- "главное запутать физику,и пока она во всем этом разберётся все будет работать"

[@ВикторИванович-ш6м]

А что он туда залил, жидкое стекло?

[@fame00]

@@ВикторИванович-ш6м эпоксидную смолу.

[@ВикторИванович-ш6м]

@@fame00 спасибо.

[@РоманСкворцов-н2к]

ПАЦАНЫ! Я ещё одну фуру с дизлайками прикатил, погнули выгружать!

[@SpicySteve-tz2so]

You had me until I saw the gasoline powered motor. If this was set up near a river and the water was turning the motor, it would have earned a thumbs up.

[@patriciomadriaza]

Que función cumple el motor a gasolina?

[@odiedelossantos-ihako]

How come the speaker connected directly? That is not powered type.🤣

[@mishaeide1818]

I was wondering that too

[@HDXFH]

It is a fake setup

[@Ken6013]

That is bluetooth speaker, just plug in and connect to the hp by bluetooth.

[@jrmychannel7047]

BLUETOOTH BROOO

[@jrmychannel7047]

Klo gak bisa diem,sebelum mencoba klo udah coba gak bisa jg baru komen

[@riturajrath6288]

but you run it through a generator then whats the need of this project use direct generator power instead of this motor

[@zmedzgaming9603]

its a waka powerd by gass and the motor is giveing to 250 v

[@iknowlaa]

maybe we miss the point here, i think he is just trying to show us that modified dynamo can produce enough 230/240v electricity by *turning* the shaft connected to the dynamo. A creative minds will extend that idea to use/connect other free energy sources such as wind & flowing river(water)..

[@akash-zg4vj]

The generator also turns a motor to make power. Its basically a rebuilt fuel generator

[@Somewhere_In_Florida]

@@iknowlaa people have zero imagination. Wind or water power is obviously the way to go. Peoples crap attitude and negativity is why they take it up the a$$ from their local power company every month. You can easily scale this tech up or down to suite your needs.

[@aboivanka6104]

U could say, he now has 2 power sources, the gen. And his modified dynamo.

[@РизванАтаев-ж1ы]

The Nobel Prize to this guy!

[@BillMcSwain]

Man, thank you so much for making this video! It seems like most everybody else doesn’t make one as detailed as this one. Once again thank you.

[@Болгарин-т5р]

Охереть, после болгарки и сверлилки, следы на роторе от токарника остались, круть

[@TTPistole]

Не придирайся. Это же Китай, там всё не так и неправда )))))))

[@GITLERUSS-PUTINUSS]

*СОГЛАСЕН*

[@gttchoppa3924]

И что? Тебе важна красота внутри электромотора?

[@มาทมะอมาทา]

All 3 electrical appliances are definitely broken. The power is not enough.

[@SimonStuff2000]

...

[@charizard4321]

This guy would be great to have as an ally during a zombie apocalypse. But this is a great build

[@nexushexus4365]

He used speaker terminals for powering the amp for the speakers.

[@americanpirate2091]

Glad I wasn't the only one to catch that too.

[@abhijithvg2753]

Diy model

[@PremanshuMitra]

Kabooom

[@vipinm.v7082]

He is an engineer

[@Ndugeusi]

He DID NOT use the speaker terminals, look closer. That is a powered speaker w/ bluetooth circuitry.

[@xinkonyese3784]

电压电流还要稳定装置才更好👍👏🏻

[@Nakatikaya]

Measure the output power with this connection!

[@indybill4]

It’s fake you don’t power a speaker with 220 volts ac. You use speaker wire from an amplifier. There is no amplifier.

[@UMBRELLACO-u3x]

Привет,от Матвеева. Кто в это верить, учите физику!

[@Borey888]

Крыльчатку охлаждения зря выкинул, двигатель перегреется. Магниты отлетят и ВСЁ!!!

[@Suavache]

Anh nói rất hay chính xác

[@hunterofwildbees2272]

Чувак реально крут. Лойс за простоту и находчивость))).

[@novik3042]

Зачем нужны там неодимы?

[@числопи-д6ч]

@@novik3042 зачем подключать обычную колонку 220V))))

[@ГеннадийПобирашко]

Да конечно круто 6 Кwт! От такого генератора, двигателя от триммера да ещё и с таким ремнём!!!)))

[@timurkhabibullin3528]

Иностранцы- Ооо молодец чувак, только нашего брата не наколоть)

[@wdamnedmelnik]

Явный поъ..бос..

[@wellwisher01]

This generator system useful in electric vehicle for recharge the batteries during car or bike running,,,,,,, great work brother,, appreciable 👏👏👏👍👍👍🔥🔥🔥🔥🔥🔥🔥

[@diyhard666]

Interesting, I believe the 220v but I wonder where the AC comes from.

[@DavidSerg]

from cable what digged behind ;))

[@MrLuigi77047]

Magnet north...magnet south....magnet north... magnet south.. equals ...alternating current... positive then negative and so on. As far as the frequency, we use 60hz in usa, the frequency of this device is totally controlled by the speed of the motor.

[@shaquedelilicss7849]

If I am not mistaking, from the looks of the stator (coil winding) there are 3 wires. That indicates that the motor is an AC motor and not a DC.

[@diyhard666]

@@MrLuigi77047 good to know. That's what I overlooked. Thanks.

[@sanju6575]

Same doubt bro. motor, fan and speak works in ac current but that small generator supply dc voltage right.how it is possible?

[@johnalexanderchaneljoseph8947]

Wonderful! It was worth watching every second of your video brother ❤

[@tomasalonsodelahera8956]

Mil gracias por compartir tu gran talento.

[@capaguevlogtv3098]

Wow napaka gandan iba ang talino mo.god bless

[@pvjraju]

Connect wattmer and measure load power and capacity of generator

[@jerryrose6895]

Just because the person wrote N S on each of the magnets means nothing a basic understanding of magnetism and repulsion would explain that something we are taught in 5th grade.

[@sleeve8651]

I think he was simply demonstrating to the viewers, the arrangement of the poles of the magnet's, should anyone care to try this. Too, not all people's have the schooling offered in wealthy countries. Sometime's necessity is the mother of invention ! Is it a filtered, well regulated device ? Likely not ! Can improvements be made ? Certainly ! But let's give credit, where credit is due ! Does this person hold a degree in electrical engineering ? Doubtful. But as you see, it doesn't always require a sheeps skin to create something ! Just imagination, will power, and determination ! Primitive people have been developing things since the beginning of time ! And not because they attended any kind of formal schooling ! Need we be reminded of the primitive people of Afghanistan, whom so far, have handed the Former Soviet Union, and now the United States, their Asses ! Who'd a thunk it ? 🤔......?

[@caloycoi3788]

12:48 LOL, I thought he would dance to the music.

[@jorgegonzalezrivera462]

Houston tenemos un problema. El motor a juzgar por el tamaño es de 1/4 HP, se nota que es de 4 polos, 24 ranuras, paso 1-4/1-6. Es un motor que para desarrollar su potencia requiere de los dos bobinados más un capacitor. Para que ese motor se convierta en un generador de 250 V, como aparece en el vídeo, necesita girar a 1500 RPM, de esa manera generará ese voltaje y una frecuencia de 50 Hz. La bomba que supuestamente energiza, es de 1/2 HP, aparte del equipo de música que si bien tiene un consumo bajo, igual suma y el ventilador lo mismo, por lo tanto entre las 3 cargas, sobrepasan los 400 W. 1 HP equivale a 746 W, el motor transformado si se fijan, se le suprime un bobinado, por lo tanto aún es menos de 1/4 HP que podría desarrollar por lo tanto difícilmente llegue a los 187 W. Pero supongamos que la velocidad con que se hace girar el dispositivo es correcta, y que este desarrolla la potencia necesaria, la tensión y frecuencia correctas...esa correa. La correa va a resbalar, es muy débil y no tiene tensión, está floja.

[@jorgegonzalezrivera462]

Olvidaba un detalle, el rotor lo hizo de 8 polos, por lo tanto la velocidad que requiere para generar 50 HZ es de 750 RPM

[@aiintelintel121]

Gas is $5 a gallon and rising. Using gas generator to run 110v motor to generate 220v is an expensive idea.

[@jeysonluyao7521]

if they put another motor to drive the generator and using battery to start the electricity then they can power each others and they dont need a gasoline motor to power up..

[@m2k_boi629]

@@jeysonluyao7521 that would not work as the power will be drawn from the battery

[@jeysonluyao7521]

@@m2k_boi629 put a blocking diode ... if you no what is blocking diode for...

[@ИванИванов-с3ю2й]

👍👍 Как тебе такое, Илон Маск?!

[@llllllllll7062]

OYttui

[@llllllllll7062]

ODAMLAR

[@jami8569]

That was fun to watch!

[@umidmatyakubov9404]

Узбекистан дан ассалому алекум хаммага тинчлик омонлик соглик тилаймиз.

[@MrBluestring]

Use the volt meter and amper mater to see the result

[@NareshKumar-nd3uc]

:-[=_==_==_=O_o=_==_==_==_==_==_==_==_=:-[=_==_==_==_==_==_==_==_=:-$:-$=_=:-$=_==_==_==_==_==_=O_o=_==_=:-$=_==_=:-$:-[:-[:-[=_==_=:-[=_==_==_==_==_==_==_=:-$=_=:-$O_o:-$=_==_=O_o=_==_==_==_==_==_==_==_=O_o=_=:-[=_==_==_==_==_=:-$=_=:-$O_o:-$=_==_=O_o=_==_==_==_==_==_==_==_==_==_=O_o=_=:-[=_=O_o=_==_==_=:-[O_o=_==_==_==_==_==_=O_o=_==_=O_o=_==_=:-[=_==_==_=:-$=_=:-$:-[:-$=_==_==_=:-$:-[=_==_=O_o=_==_==_==_==_==_==_==_==_=O_o=_==_==_==_==_==_=O_o=_==_=O_oO_o=_=O_o=_=O_o=_==_=:-[=_=:-$:-$=_==_==_==_=:-$=_=O_o=_==_=:-$=_=:-$:-[=_==_==_=O_o=_==_==_==_=O_o=_==_==_==_==_==_==_==_==_==_=:-[=_==_==_==_==_=O_o=_==_==_==_==_==_=:-$=_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_=:-$=_==_==_=:-$=_=:-[=_=:-$=_=:-$=_==_==_=:-[:-[=_==_==_==_==_==_==_==_==_==_==_==_==_==_==_=:-[:-$=_==_=:-$=_==_==_==_==_=:-$=_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_=:-$=_=:-[=_==_==_==_==_==_==_==_==_=:-$=_=:-$=_=:-[=_==_==_=O_o=_=:-$:-[:-[=_==_==_==_==_==_==_==_=:-[:-[=_==_==_==_==_==_==_==_==_==_==_==_=:-$=_=:-[:-[=_==_==_==_==_==_==_==_==_==_==_==_==_==_==_=:-[=_==_==_==_==_=:-$=_=:-[:-[=_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_=:-[:-[:-[=_==_==_==_==_==_==_=:-$=_=:-$=_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_=:-$=_=:-$=_==_==_==_=:-$=_==_=:-[=_==_==_=:-$:-[:-[:-[:-$=_=:-[:-[=_=:-[=_==_=:-$=_=:-[=_==_=:-$=_=:-$=_==_==_=:-$=_=:-$=_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_==_=:-[:-[=_=:-$=_=:-$=_==_=:-[=_==_==_==_==_=o:-):-$O_oO_o:-[O_o:-[

[@NareshKumar-nd3uc]

Pppppoopppoppppppppppppppppopppppp0p0pooppooopppoopoppooopp000ooolpo9poppppppppppopoopppppoppppppp

[@NareshKumar-nd3uc]

Pppo

[@NareshKumar-nd3uc]

Ppp

[@NareshKumar-nd3uc]

P

[@Momi_Basu195]

How long it will work? Epoxy may be mealt due to heat

[@froglegs4910]

Correct ! Fire 🔥 will burn out ! Destroy everything at last !

[@marlotom4074]

Use your sentido komon

[@Meop79]

The heat will demagnetize the magnets before it catches on fire as well...

[@marceloaraujo970]

Sensacional trabalho executado, parabéns vc é o melhor! Goood job...1000 likes.

[@pravasiniparida3719]

Sir motor rpm please

[@claydo364]

Well done 👍

[@allenhargis4317]

the frequency or hz on that setup would be very high. great rotor build though.

[@985haus]

Curious what frequency this is generating? Also what is the amperage output?

[@noelompad3592]

that is what i want to know too

[@mottbone]

If he's limited on electric test equipment to find out his frequency, I believe all he'd have to do is find a mains style electric wall clock with a second hand to tune his speed. With a little time and math, he'd be able to get a close approx value.

[@985haus]

@@mottbone id love to see that.

[@3dcreations690]

Engine sound should change on every lod on generator but here is same

[@pointedspider]

It's not enough load to make a difference

[@emmanuelhud1]

Derr....have you ever owned a generator