This mod has nothing to do with what the radio will TX and RX on. Its a mod for the fan, the fan wll be running while the radio in in RX. The guy has put this in the heading. Thx for the video...
@tywilliams77808 жыл бұрын
simple, cheap fix for the heating problem...worked perfectly!
@kwiatkowski_4 жыл бұрын
Dzięki Marcin, przydało się na gorącą 706.
@slartybardfarst527 жыл бұрын
I done mine today, makes a huge difference
@franc_ea6fs3 жыл бұрын
Extremely simple and really effective. TNX!
@kaptenalgysson85403 жыл бұрын
Hi! Have done exactly this mod on my IC706MK2G, works great now, always low temperature even in long transmissions !! Best 73 from SM6AAL
@Wheelabarraback7 жыл бұрын
Thanks very much !
@djloot9167 жыл бұрын
What's the song in the background?
@johnrc196112 жыл бұрын
Just asking ???? I have done the MOD to expand the radio, by taking out the diode, but I would like to know what the other diode is for ???? Is it to BLOCK the TX on 88MHz to 108MHz Bye from John 73's
@emavideo3 ай бұрын
does this mode run the fan only when on? I dont want to run the fan when the radio is off. Somewhere there is a mod that runs the fan in a slower speed when you turn it on and higher speed when you transmit.
@SV1RXI3 жыл бұрын
is this issue excists to first models ,mine have serial number 107..... ,i don;t get it to my hands yest just bought it from a store used as new condition and read about this problems
@truthseekers6668 жыл бұрын
Do you know if a 706 first model, is meant to have the fan running in RX mode. Mine does. I wondered if someone has modified it already or if it was meant to be like this.
@n1kkri8 ай бұрын
The fan on my 706MK2G runs occasionally when in RX too. I don't mind TX but in RX iI don't like listening to it. I might use the remote cable and place the 706 further away.
@arunaspaulionis83506 жыл бұрын
Dziękuję za piękne video.de LY3SR. 73
@carlmoren3953 Жыл бұрын
Good morning! Shortens the fan's life?
@TheTemporalAnomaly Жыл бұрын
The cost of replacing a worn out fan is much cheaper than replacing the components that are commonly damaged by heat in this radio. Even with this modification the fan will last for years, I did my mod 12 years ago and my fan is still ok.
@carlmoren3953 Жыл бұрын
@@TheTemporalAnomaly 👍
@biologobrunao10 жыл бұрын
gambiarra kkkk
@janerikfalk10 жыл бұрын
Do you make modifications without knowing why? I think you did open your transiver for out of band Tx, but you do NOT be able to transmit on 70-120Mhz, connect a frequency counter and Tx there and you se that the radio dosent. Tnx sq7bce for the clip.
@f.allenrisler53034 жыл бұрын
That was the worse soldering job I have ever seen. If you do this like his example you will likely have the resistor fall of the cold solder glob and short out something causing damage to the radio. His first cold solder glob nearly shorted out his red fan wire (Positive) to ground. Apparently no one ever taught him how to make a strong physical connection before soldering. You should keep the leads of the resistor short, bend them in a loop/hook, tin and solder them to a wire, then prep and tin a hook wire where you need to make contact.