Idra 1600 Metric Ton Horizontal Cold Chamber Die Casting Machine

[@Kxkv423]

For a die cast shop this place is ridiculously clean lol

[@Pravin-1907]

2:25 injection plunger moving not ok(velocity not gradually increasing)..may be tip stuck-up, or poor lubrication in tip

[@anthonyarnold906]

Correct

[@diogovendramin769]

Pode também estar com a servo valvula da 1° fase com problema, ou até a servo valvula de alivio da frente do cilindro com problema.

[@Pravin-1907]

Presently i am wrking in 2700tonnage machine will full robo automation...after seeing this video feeling proud..i am lucky to wrk there

[@hazemsalhab4618]

is there an iron die casting machine

[@Pravin-1907]

@@hazemsalhab4618 no..nly aluminium die casting.

[@hazemsalhab4618]

@@Pravin-1907 thanks for your reply

[@ShiMiDCM]

@@hazemsalhab4618 no , melting point of iron is tooooo high , only aluminum,magnesium,zinc, lead and brass die casting

[@YoniRios-e7j]

Esto es una mega maquina 👍👍😄

[@shanechambless8]

The velocity on that shot profile probably looks like shit those casting would fail an xray they should add a spray robot and speed up the extractor robot

[@MrMielMonteur]

standing inside of the safety doors is one of the craziest things ive seen in a die casting machine. They should pay me $100000 to do this with this machine

[@ShiMiDCM]

robot can do this job😄

[@shafiqahamed8712]

Cold shot compunent not ok punger tip struckup problem i thnk second phase nitrogen plunger lubrication correctly mainten,,?

[@steveameriault4377]

Ya were I live you can’t be standing in there like that when the die opens up and even the c-frame dip well every thing is covered cages around everything

[@hpdcpathshalasds]

Steve Ameriault kzbin.info

[@invain143]

Operator is helping/spraying the shot piston to go back. Timing is everyting in this operation.

[@Powerboywow]

well if the piston is to hot and not using release powder then it will get stuck, and if the piston overheat 90% of time is a cooling problem, never the less you should never stand inside of the safety door

[@alejandrorangel9799]

@@Powerboywow que es el polvo de liberación

[@gabewaite7984]

Used this or a very similar one when I was 18 first job in a factory, did not like going between the die faces when there was a problem 😂

[@alejandrorangel9799]

Alguien ah trabajado con un sistema de cucharón, siempre se derrama?

[@nicktaylor5819]

Your ladle translation was far to quick in comparison to the operation speed the castor shouldn't have been stood inside the guard door during die closing and she is wrong with the second stage locking vavle for the moving platern took like 10 minutes to complete full locking

[@SPtrade3338]

Please contact aluminum pressure die casting machin 180 tone rapit or techno company

[@nirajshah6893]

Send your number

[@tanveerkhan9221]

would not recommend standing by mould clamp imagine if the ejector pin breaks or you get caught between the die half's so dangerous

[@hpdcpathshalasds]

tanveer khan kzbin.info

[@vikastelang6736]

Please toyo 900 bd vt new video upload

[@haituoinjectionmoldingmachine]

Welcome Haituo

[@IshanPegu-s8h]

Injection side effects

[@trgasser]

dont slip cause that die isnt gonna care when half your body gets slammed shut smh just watched a video of a guy getting caught in one and it tried to lock up with him in it oh the guy died too

[@petecarns8992]

Oh baby, I ran a 600 ton in the 80's ,Emerson Electric in Rogers AR. Automated bucket, control panel. Conveyor/water tank below machine, with big hydraulic press to trim fresh gates off nice fresh cast parts. Aluminum VAT that held 40 to 60 gallons of 1400* degree molten metal. This thing burnt hundreds of times a day. Still a thrill knowing I could keep this thing running for 12 more hours when they tell you it's junk at the start of the shift. Fell asleep in the conveyor belly one time with a pair of pliers in hand. Another time it started a cycle while I was leaning in. Still a thrill after all these years, WOOOHOOO!

[@trgasser]

Pete Carns i run the 1650 its a newer model than the 800 and i know what you mean by keeping her going for your shift the machine is older than my grampa

[@trgasser]

lol living the diecast dream

[@rajeshlohar5159]

trgasser hello can i get your no please i need to talk regarding this

[@tanujchoudhary2383]

Sir hme tie baar kholne hai 800tan k or full Tait hai to kse khole

[@cupidbentley3121]

You're smoking crack. I'd never get in between a die with a machine that isn't locked out. Holy shit. Plus, the sliding door is for the operators saftey! What if that thing flashes out??

[@jimbobbob9063]

That’s no IDRA machine.

[@satishchandpandeypandey6583]

Unsafe condition very poor safety

[@ajaykumarkaliya9033]

Hpdc operator jobs me

[@vikastelang6736]

I am in indean

[@hpdcpathshalasds]

Vikas Telang kzbin.info

[@Fddgg-k4d]

this machine maker don't have sense will making this machine ... how can an operator move inside a machine during opening and closing of dies... before safety door are open a operator is seen inside.....

[@stepankrnavek8645]

it looks that this foundry has no skills and knowledge about die castings: 1. as you explained situation with doors, 2. casting is still in mold and operator is doing lubrication of mold..wtf? 3. casting is ejected from the mold by robot and there is no move with casting on control sensors if casting is complete... whole proces in this foundry makes no sense... I expect that this foundry isnt europe...

[@eddiebacon127]

lakshmi narayanan i bet he is illegally recording it.

[@hpdcpathshalasds]

lakshmi narayanan kzbin.info

[@invain143]

@@stepankrnavek8645 in my work experience with these fully automatic bigger casting machines, sometimes the operator need to catch up adding spray lubricant every once in a while especially if the Mold is a little bit old. If you don't add up lubricant manually, aluminum will get stuck up in the mold the Job will be much harder to take aluminum out, damaged mold/pins with lesser production.

[@sermecanicmoura]

Shit machine no security bars, i whork in a factory, my friend died crushed in the mold..

[@sambingham2889]

That shot forward was pathetic.

[@hpdcpathshalasds]

Sam Bingham kzbin.info

[@casperb5553]

It needs to be laser aligned

[@ShiMiDCM]

we are die casting machine manufacturer in China, contact with me , i show our 2000t machine 😄😄😄😄

[@manasshaou3571]

Old proseser

[@hpdcpathshalasds]

Manas Shaou kzbin.info

[@satishchandpandeypandey6583]

This is not like

[@eddiebacon127]

Im on a baby machine compared to this.

[@shanechambless8]

These are baby machines compared to what I operate 35 to 45 ton dcm

[@hpdcpathshalasds]

Eddie Bacon kzbin.info

[@Pravin-1907]

This is baby and very old technology unsafe worst machine... compared to my machine

[@cupidbentley3121]

You should see the presses I run. 150k lbs of die. 70k lb cover die and 80k lb ejector die

[@chrisdaniel5004]

Die Casting ? What a dying career in the U.S.

[@沈佳儀-k1g]

給湯機前待機太久，拍攝手法太爛，拍三小！

[@hpdcpathshalasds]

沈佳儀 kzbin.info