II How to oxygen (O2) analyzer calibration II Zirconia cell replaced II

[@waqashabib1674]

Good work keep it up..

[@rohitjoshi2943]

so good keep it up...

[@asimq16]

Good job bro

[@PowerPlantInstrumentation]

Thanks for your comment 🙏🏻🙏🏻🙏🏻

[@baljeetjangra948]

Good job vire

[@pardeepkumar9844]

Best vedio for calibration

[@PowerPlantInstrumentation]

Thanks

[@ajaymaurya4378]

Bahut help full video hai ❤❤❤ But sir ji standard gas kon si hoti hai or kitne % main aati hai

[@arshadimam9966]

Thanks bhai Please bataia ye analyzer kha pe installed h mtlb kon se unit k exact kis location pe....

[@PowerPlantInstrumentation]

Ok ✅ thanks for your comment and suggestions

[@om-su7cg]

Sir no2 gas zero ke liye span ke liye reference gas kya use karte hai

[@jitubabusay2826]

Sir span cal 8.0 gas mai hota hai na,plz reply

[@jahurahmed6353]

thanks so much ❤

[@PowerPlantInstrumentation]

Thanks 🙏🏻

[@pardeepkumar9844]

Nice vedio

[@PowerPlantInstrumentation]

👍👍

[@bhagwansinghlodha939]

bhut achhe se samjhaya hindi m ydi sir standard value dene pr .4 dene pr . 2 ya .3 aay to kya krna chahiy

[@PowerPlantInstrumentation]

Aapne vedio me dekha hoga jab maine zero calibration kiya to standard value se match nahi ho raha tha isiliye to calibration kiya maine . Calibration me jo error/ drift hota hai usko adjust kar leta hai analyzer.

[@PowerPlantInstrumentation]

Any other doubt then ask me

[@bhagwansinghlodha939]

ok sir automatic arjest ho jata h . sir vibrationn sensor key phasor ko v samjhaiye

[@bhagwansinghlodha939]

sir conductivity analyzer k bare m v banaiye

[@PowerPlantInstrumentation]

Sure Jaroor bataunga vedio about conductivity

[@jahurahmed6353]

👆☝️👍🖐🤘good morning sir/very good job👍👌✌🖖🖕👐👏👋

[@PowerPlantInstrumentation]

Thanks for comment 🙏🏻

[@TheGamaCom]

Bahut shai Boss

[@TheGamaCom]

Fantastic

[@rijilaarukandy1503]

hii good video. can you please tell me why you given first span gas air and then 0.4 zero gas?

[@PowerPlantInstrumentation]

Thanks for your comments 🙏🏻 it is not necessary you can do any first

[@susantakumarsahu6031]

Calibration successfully both span and zero but in load time value not correctly when load increase or decrease.plz suggest

[@PowerPlantInstrumentation]

check Zirconia Cell

[@InstrumentTechnicianVP]

Thank you for your helpful video and I have a confused question. When you remove the detector, the boiler is shutting down or still operating? Thank you so much!

[@PowerPlantInstrumentation]

Thankyou so much for supporting my channel and like videos . Boiler in Operating Condition . If any other question then ask me

[@InstrumentTechnicianVP]

@@PowerPlantInstrumentation thanks for your response! The boiler is operating, the pressure of flue gas inside the boiler isn't influenced to boiler ? I mean it is maybe exploded or another problem occurs

[@PowerPlantInstrumentation]

@@InstrumentTechnicianVP No, there is negative pressure in the boiler. So there is no problem in getting the sensor out.

[@InstrumentTechnicianVP]

@@PowerPlantInstrumentation thank you so much

[@PowerPlantInstrumentation]

🙏🏻

[@viniciusmelo984]

Thank you for sharing the video! When you set the atmosphere on the open port to 21% O2, is the plant at sea level? If not, can this negatively affect the process the instrument is in?

[@PowerPlantInstrumentation]

Yes atmosphere oxygen concentration at seal level .

[@AvinashKumar-rj3ix]

Good

[@raunakmohangarg8440]

Zirconia cell cost?

[@INSTRUMENT_GYAN]

Sir SOx and NOx calibration ka bhi vedio banona (Forbes Marshall)

[@PowerPlantInstrumentation]

Ok

[@minhphanthe239]

Where did this analyser take place in this video ?

[@PowerPlantInstrumentation]

Air Pre Heater Inlet (APH) of Power plant

[@TheGamaCom]

Thoda theory part bhi cover kijiye Boss

[@PowerPlantInstrumentation]

Sure sure

[@ramgr6888]

Which port should be open for span calibration and which port should I give reference air 1-1.5kg/cm2. Pl explain clearly

[@PowerPlantInstrumentation]

I have shown in this vedio -only CAL port used for zero & span calibration.

[@sandeepsaini6493]

How much supply given to heater

[@PowerPlantInstrumentation]

230vac

[@shrikantkhonde5446]

Unit kya hi ?

[@PowerPlantInstrumentation]

Percentage of oxygen concentration. (%)

[@sandeepsaini6493]

How much suppl

[@PowerPlantInstrumentation]

230vac supply given to heater sir

[@pankajpatel662]

Services engineer no