INFINITI G35 💥 NISSAN 350z - Misfire Random P0300 - Ignition Coil and Spark Plugs INSTALL

[@MotordyneG35]

Spark plug gap is .043. After 50k miles, I had a couple plugs reading .055 gap. Immediately after the install, car's idle was strong, no hesitation or random dying anymore that went on for 2 months with NO CHECK ENGINE LIGHT. Changed my air filter, did an idle relearn procedure hoping that would fix it; it did not. Changing out my spark plugs and ignition coils, fixed my issue. NEW SPARK PLUGS INSTALLED..... NGK Iridium IX PLFR5A-11. How to gap spark plugs.......kzbin.info/www/bejne/oGa6maSNhdR_is0

[@lcmurdal]

Great vid! Where did you get the plugs and coils?

[@MotordyneG35]

@@lcmurdal ....10:26 I tell you where I got them for FREE.

[@v36vhr]

What else could it be if I replaced plugs and coil packs and I still have a p0300 and a p0301?

[@MotordyneG35]

@@v36vhr ....dead fuel injector.

[@moonlightg3510]

You have a way to chat outside of here? I have a few questions for you.

[@koniko169]

Lol yeah man i agree with the other guy. You are a huge help. Singlehandedly have kept my car running and kept me from getting a 370z. 10/10 for content.

[@nickpapageorgio1299]

Things go wrong with these cars they're old, but the good thing is they happen one after another so you get to know your car and slowly upgrade it. They are old cars but they will last a very long time and look and run nice. Its worth the repairs. Everything can be done yourself just research and study the repair manual, don't pay the dealership they will triple the price and you can fix so many things for the price of one job at the dealership. Spark plug change is 368$ at nissan here i did my ball joints, belt, and plugs waaay under that price. Ball joints alone 1279$ and it only costs 72$ to diy.

[@ranwats2]

i have no check engine an car putters after changing spark plugs

[@joanrodriguez2180]

That’s a fact I had a hole week dealing with a misfire! Then I watched your video and the part you show to keep the coil cables separate, I was mixing 2 of my cables without even noticing. I watched your video and went straight to the problem big help ✊🏾💪🏾

[@lonelymontana7871]

just finished changing my spark plugs and coil packs . all coil packs are connected properly . however , strangely, the car wont start unless I have an obd reader connected to it ? help please

[@tcblackg35]

Motordyne G35 Thanks for the video brother I've had my G for less than 2 months and it started acted up and shot a p0305 code. Changed out all my spark plugs and ignition coils after watching your video it was a breeze. Car runs better than when I bought it now!

[@robertm5969]

Thanks bro! I think you just fixed my P0300 which 2 shops looked at and couldn't fix

[@BigBoyz33]

Are the O Reillys coil packs good? My Z misfires like hell and i need to get some coil packs. I changed my spark plugs, no oil in the wells or leaking valve covers and cleaned out the MAF/Throttle body. Did all re learn procedures. No vacuum leaks. All i got left are the Ignition coils

[@dannyrodriguez7407]

Bro you are a huge help! Thank you for showing us i have myself a 03 G35 coupe and just started to do the work on my own cause these mechanics are something else smh but yeah man thanks been using your videos to get the work done! Love your car keep up the videos

[@troyspace8384]

Man how much coil packs cost i have a 2007 g35s

[@GLifemine]

Jus curious but why is it necessary to install the coil packs back in the same cylinder? Never worried about this with my past vehicles & didn't have any problems. Only the coil pack connectors have to go back to the same cylinders.

[@heilong79]

Dont use a q-tip for putting on the grease, micro hairs will get in there.

[@zeebracove2992]

thank you so much man. great and detailed tutorial. Helping me even years after you've uploaded it 🤙

[@brianlee677]

I just did the valve cover gaskets spark plugs and CAI on my brother's g35 the coil pack wires didn't seem long enough to not correlate with the correct cylinder.

[@acerv136]

How can you tell which is is 1,2,3,4,5 or 6 on the ignition coils ?

[@westsideray7324]

Check your alternator connector/make sure it’s Grounded! Make sure the power supply line is tight! But the Harness! Check wires! I had to replace my alternator connector, p0300. Solved my problems once and for all…. I swapped out the fuel ⛽️ pump Cleaned injectors/Changed plugs/Coil packs…. Changed fuel rail lines…. Was on my way to changing injectors. While removing my alternator to do my valve cover and Clean my bottom block, ALTERNATOR!!! 🤦🏾‍♂️ HARNESS

[@thatguyd11ceo26]

Hey I’m having the same thing on my 2008 g35, I changed the spark plugs but it still does the random die on idle, so I should change out the ignition coils too?

[@kami_dred7319]

Did it work for you ???

[@jorarr5174]

Did po300 come out on ur car before u swap everything out ?

[@richardmedina707]

Thank you so much! You helped me fix my 350z! You saved my wallet again

[@GladlyKillmore]

Soon as you pull it out, stick the nut back in. Best advice I've ever taken 😃

[@rcole718]

My car was running fine until I changed the upper plenum cover. The idling immediately got rough and would idle high at 2000 rpm, then drop to around 1000, then dip to 600. One place said it was a vacuum cap. Didn't fix much. Dealership said it was a P03000 code and their computer couldn't pinpoint the issue. Would swapping out spark plugs fix this? (2005 G35 6MT, 96k miles)

[@MotordyneG35]

You have a vacuum leak somewhere after changing the plenum spacer.

[@jenningswest79]

Quick question I've watched a lot of your videos man they're real clean detailed I love it I have a Infinity G35 coupe sport the code P0304 popped up on my computer was looking for a video like this so you got subscriber I'm coming going to check my spark plugs and injectors and I will update you! Thanks a lot! Just got to go grab me one of them magnetized spark plug sockets

[@kristiewilson209]

hey i have a 07 g35x check engine light flashing running poorly like its fuel related changed my coils and spark plugs and it made no diffrence clean maf sensor nothing what would u do next p0300 is the only code random misfire please help!!!! thankss

[@Bigazzham]

Was having the same problem with my z. Changed my coil packs and spark still a misfire. Ended up being a stuck injector. Pull all your spark plugs out and look to see if one is way blacker then the rest. Hope it helps.

[@kristiewilson209]

@@Bigazzham i just sat un the car pushing the rpms and it cleared on ita own so yeah i think mine was a injector was clogged lol

[@Nissan370_z]

My 370z got 38,000 miles and I just changed the spark plugs to autolight from auto zone. And now it spudering like 10 times a min for just the first 2 min then it goes away. Guess I'm taking them back and getting denso like it comes with

[@4Him4u2]

Your video gives just the right amount of detail. Thank you for taking the time to share with us.

[@maksteezy]

Changed sparks,ignition coils, fuel pump. Did oil change. Car was running smooth for a day. Car died next day I swear its the battery. Put a new battery in voltages were correct. Then my awd, abs,vdc, brake lights came on,lost acceleration..I've already cleaned the throttle and mass air flow sensors as well. One thing after another. Hope it's not a parasitic drain or something because I had just changed the alternator smh..... Would it be an ecu issue?

[@adammarron3085]

How u torque it without the socket getting stuck/attached to the spark plug

[@truthtellerlikeitornottrut7735]

hey question, my coil is misfiring on cylinder nymber 5, how long should it take me to switch out one coil on cylinder 5?

[@rocksev21]

Changed spark plugs and still have a cylinder 1 misfire. Also changed over cylinder 1 coil and same thing.

[@MotordyneG35]

What is the check engine light code?

[@taylorrowe8703]

On the throttle body side what wires go to what ignition coils?a buddy and I redid his and it keeps coming up with a multi misfire code and I think he got one of the wire connected to the wrong coil....i would really appreciate the help!

[@Trini_Fishing_Entertainment]

I need the same question answered. just did mines and I think I put the wrong wire harness to the wrong coil pack and my car is misfiring like a mug

[@taylorrowe8703]

@@Trini_Fishing_Entertainment get at me on Facebook and I can get a pic when my buddy is around.. I fixed his car and we got the wires mixed up and it was throwing crazy codes and running like shit...the passengers side is next to impossable to fuck up but the drivers side wiring has a little more play to it

[@jose.valles7572]

All I have is an Intake and a straight pipe Y pipe, should I get the cold Spark Plugs?

[@sirlucid4432]

what coil pack did you buy? The O'reily ones only lasted a bit right? OEM is the way to go but its 80 bucks each! I got the P0300 code but it would miss for a few minutes and go back to running on 6 cylinders, is that the START of a bad coil pack?

[@mightymike130]

Yo im having the exact same issue! It will do the random misfire for a few minutes and then the car will be fine again. This shit is frustrating!

[@stevenpenland4566]

Did you happen to figure out the problem and fix it? Mine is doing the same thing and I've seen like 50 comments with people with the same problem and nobody ever answers if they got it fixed or not and what it ended up being. FRUSTRATING!

[@JuanGarcia-oi3nr]

Any updates ?

[@red_day6097]

My car was dying at idle as well and I just changed the spark plugs but not the coils and now I have a misfire and my check engine light is on. 1 of my plugs had oil in it when I pulled it out. Any thoughts?

[@rashadvq]

Same happened to me

[@MrSnakedoctor85]

What size is the magnetized spark plug socket?

[@robertm5969]

What is the OEM coil pack brand? I think Hitachi right?

[@los7948]

Did you use racing Sparks?

[@nikkogonzales4818]

@motordyne_g35 I watched the vid and I was trying to listen to which spark plug PLFR5A-11 or PLFR6A-11 you went with in the vid but I couldn't catch it. Could you let us know. thanks for the great info!!!

[@DARKWoLF52297]

You recommend the 6A if it’s modified? Or the 5A?

[@mrsquidwardtentacles6291]

Hey I have a question for you. I have a 05 g35 coupe. If the car has ever had a rough idle and drives rough as if it’s a diesel and running like shit, and the engine light is flashing...would that be because of bad coils? I replaced my spark plugs already and it still does it. The roughness comes and comes which is weird

[@MotordyneG35]

Yes! Flashing engine light is multiple misfires.

[@Vq35g35]

Did you find the problem?

[@stevenpenland4566]

Did you find and fix the problem? Mine is doing the same thing.

[@rogertalavera5004]

Go to auto zone, en get the scanner, and the guy print the code, my experience was cylinder 5, change the coil, and working good .

[@Cribbie_]

I just finished doing mine, and it still has sputtering sound

[@christianlupo5587]

Replace Coil packs, Replace all 6 get the good ones it’ll cost roughly $200-$300 for all 6 but you won’t have to worry about replacing them for awhile. You should always replace Coils with Spark Plugs.

[@Cannon5Loaded]

This helped alot...thanks man...i wish i had the sockets to do it myself but im getting it done in the morning asap. 👍🏽

[@fgunter5210]

Hey man I changed a my intake plenum gaskets and valve cover gasket and covers but I accidentally over tightented 4th cylinder ignition coil and now it's just spinning when I try to loosen it how would I remove that

[@MPerformance2]

Can i get the link where you get your spark plugs at?

[@Akanematcha]

If these go bad can you get the code P2A00??? Please let me know cause the code keeps coming back and after clearing it runs fine but later it comes back after an 1hr

[@zakk5688]

Hey bro. G owner here. I have an 03’ and it was shaking extremely badly at idle and misfiring like a bitch , so me and my buddy changed the spark plugs and ignition coils and it still misfires extremely bad. The check engine light flashes. After I did the spark plugs and ignition coils I put sea foam in it to help clean the fuel injectors. It’s STILL misfiring after those 3 things I did to the car. Any idea what it is ? I’m at a complete loss and confused as hell. Thanx if you do get back to me !

[@AR_BSME]

Zakk Same exact story how did u fix !!!!!!!!!

[@RyanInFlorida]

@@AR_BSME Did you ever get your issue resolved?

[@druwilliams9821]

My problem also.. gonna change the pcv valve

[@jaysonmason279]

@Zakk hey did you ever resolve

[@xqxc]

my car is having a misfire right now and a reader told me it was the 2nd cylinder. i changed the spark plug on it but didnt change the coil and im still having misfires. i also had a cam shaft bank 2 sensor on so i went ahead and replaced that too but my car is still misfiring. what should i do ? should i replace the coil aswell ?

[@sneakerguy2430]

Im having the same problem, I changed the spark plugs and nothing. Mines an automatic and when I start it up it sounds like a rotary .

[@xqxc]

@@sneakerguy2430 could be misfiring. Did you change the ignition coils?

[@sneakerguy2430]

@@xqxc i haven't, I changed the coil 1 with the second but it still sounded the same

[@xqxc]

@@sneakerguy2430 did you use a reader? If you don’t have one, just go to auto one or orielys. Ask for their reader. It should tell you what cylinder is misfiring . Once you find out which cylinder, change that coil. Or if you want you can change all 6 coils. Your choise

[@sneakerguy2430]

@@xqxc I've had p0300 Po301 .

[@iliasiakimenko]

Idk if it was just bad luck or something , but I just replaced my cam shaft sensors in my 04 and then while I was driving boom I got the random misfire code and a fuel rail sensor code . Does any1 know if this would fix those or should I just take my car to a professional?

[@markhebish4242]

Bro u know what sucks I changed both and still got the miss fire and the horrible code, i wish the computer was more specific 😅 but it gotta be random ig

[@anonymousgaming7332]

What brand ignition coils are those

[@jspansera]

What brand torque wrench are you using?

[@austinbradley3411]

Awesome vid. Is the De Aand hr vq"s plugs gap is the same? Cause my ngki was gaped to .44 i have the de rwd automatic

[@MotordyneG35]

Yes, it's the same. I go over why they come pre-gapped at.044 and even though the service manual says .043 is the gap, no need to try to move .044 to .0443, that is close enough; so they are pre-gapped. Not every spark plug is pre-gapped for every car......kzbin.info/www/bejne/oGa6maSNhdR_is0

[@christianalbino2802]

I need help recently changed cylinder 3 spark plug and coil and car is still hard misfiring and idling

[@scottjohnston3198]

Help, 2011 g37 hard starting, rough idle, I’ve had 2 codes thrown p0300 and p0304, had master mechanic look at, he changed spark plugs but still the same, strange I can disconnect the battery and reconnect and it runs great for about 30 minutes then starts acting up again, any help to this issue would help me, does this sound like a coil pack issue?

[@glifics951]

Scott Johnston I have the same problem right now

[@scottjohnston3198]

@@glifics951 Hey, I've changed my MAF Sensors, Camshaft sensors and cleaned my intake manifolds, I i'd like to change my crank sensor but I'm having a hard time finding it, I have not checked my spark plug gap but also will follow that up with a new set of coil packs, it just does not make sense. Someone told me I could have a problem with the piston in cylinder 4. If the plugs and coil packs don't work, I'll take it to the mechanic and pray he happens to find an vaccum leak or something inexpensive. If you figure this out before me, please let me know! Scott

[@nickpapageorgio1299]

My 350z hesitated when i hit the gas on the highway i changed my spark plugs and it stopped. The throttle response is instant now. Now i have to get a new radiator because its leaking lol

[@MotordyneG35]

If you have problems bleeding your radiator make sure to check this video out...kzbin.info/www/bejne/pWKWmq1_rqp8atE

[@grandesdsd]

Its doesn't matter which ignition pack goes first just make sure that the connected matches right?

[@MotordyneG35]

Correct.

[@4klp59]

Soo you don't have the hitachi one ? Everyone recommends me those

[@MotordyneG35]

Paul Anthony ....hitachi doesn’t offer any warranty, one fails you buy a new one. I go with the lifetime warranty parts. Free replacement if it ever fails.

[@4klp59]

Ohhh thats good 😂 didn't see it that way

[@bryanpuga1775]

Hey man I have a quck question my g37 sedan is throwing code P0300 I replaced the dork plugs and when I turned it on and rev it once it hits 2500 rpm the car starts to jerk and idk what else to check I’m new to this Infiniti stuff would appreciate the help

[@bryanpuga1775]

I could send you a video if you don’t really understand what I mean

[@Bigyellowburner]

I thought the factory plugs were iridium? Why switch

[@mf7338]

I had the same problem with mine, but it was the one of the piston rings where worn out completely so im rebuilding it currently

[@MotordyneG35]

damn....that sucks! How many miles on that piston ring?

[@mf7338]

@@MotordyneG35 currently 225,000 approximately I don't know exactly because it's at my grandfathers shop. I use his shop because he has pneumatic tools and other miscellaneous tools I don't have Edit:also my vq was smoking really badly at the end

[@MotordyneG35]

@@mf7338 ....225k is still up there in mileage, can't really complain, the G was definitely driven. 250k-300k is all you can expect with perfect maintenance. I am at 180k miles currently.

[@wavyjeff]

just bought a g35 so i decided to do a tuneup. so i put brand new spark plugs and coil packs from rockauto. i went to start the car then had a really bad misfire!!! WTF!!! so i checked the codes and it was for p0300 . im like how could this be. i went back and checked the wiring and i found i screwed the wiriing for cylinder 1 & 3. that solved my issue and it was purring !! guys make sure you do them 1 by 1 because it can easily be screwed up.

[@JuanGarcia-oi3nr]

How did you fix your issue

[@Guss0531]

You making me nervous with all that hand shaking . 😄😄

[@guitarpro594]

Hey could you help me out? Got code P1168 last night for closed loop control bank 2. I just want to confirm this is the driver side O2 sensor?.. Thanks buddy!

[@dlinder7]

Def appreciate the content this was a BIG HELP.

[@killer4hire90m9]

really good video dude....your the best!!!!

[@Myfoodeatsyours]

The electrical grease should only be used on the tail of the plug because it conducts current. If it's all the way down the side of the non condition ceramic it can cause spark jump to the ground/threaded side of the plug and cause misfire codes as well.

[@robertm5969]

Dielectric grease PREVENTS conduction

[@thisnameislessembarassing]

I was patiently waiting for you to pull number 6 and find a whole lotta oil on the plug. That's what happened with me!

[@MotordyneG35]

Cylinder 6 is most common to have oil in it first before a new valve cover is needed. When I pulled the spark plug out, you can see there is no oil and also down inside the tube there was no oil. The gopro on the gimbal couldn't fit over there to get a really good view. I was also worried about cylinder 6 because I did not feel like doing another valve cover job.

[@halynch99]

Do you have to replace coil packs with OEM? I followed your video step by step. Changed out plugs with same ones and changed coil packs. Now I have hard shifting occurring sometimes. My G35 only has 34k miles.

[@MotordyneG35]

No, the coil packs I used are not OEM. Hard shifting is transmission not engine. Any check engine light?

[@guitarpro594]

Perfect timing, doing this today! My coils are not coming out in one piece so I picked some up from advanced and some ngk plugs the 5s not the 6s although I should have grabbed the 6. Thank you for posting this! Lol Edit: Have you replaced your oil pan gasket? Mine is leaking really bad when I go fast and it smells like burnt oil. Just wondering if it is Just the gasket on the pan doing that? It looks like it sprayed out.. I'm getting the new one today.

[@MotordyneG35]

Yeah don't buy off ebay, the half price spark plugs have to be fake. KZbin videos proving it. I also went to the parts store to not risk it. The 6's? Are talking about 1 step colder spark plugs? PLFR5A-11 - Factory Heat Range (5) is best for vehicles without any modifications PLFR6A-11 - One Step Colder (6) is best to be used when any engine modifications have been done (Including air intake, exhaust, etc.) Yeah, I should have also gone with the 6's. I went with OEM PLFR5A-11 heat range, Iridium IX though. I completly forgot about 1 step colder, oh well they are already installed now and it runs much better. The random stalling went away. The gap was way over too on the used plugs. www.z1motorsports.com/ignition-system/nissan/oem-vq35de-spark-plug-ngk-plfr6a-11-p-3187.html

[@guitarpro594]

@@MotordyneG35 Awesome! Thanks for the link and prompt reply, I appreciate it. Those are cheaper than I paid, picked mine up from advanced and they were 14 a piece. Yes, I was talking about the one step colder plugs haha. It's raining at the moment so slightly gridlocked as I do not have a garage🙄. I love your vids and your G. Can't wait to get my Motordyne ART pipes and shockwave exhaust

[@vgyvgoiy]

For some reason, my check engine light would come on asking to replace coolant temp sensor but i already replaced it. After a few weeks of it being on, it goes away. This keeps happening. Anyone have an idea? Thanks.

[@ajmadera5927]

Man I’ve been wanting to do this lately ! Thanks for the informative vid man. So G is so nice ! Wish I could afford that exhaust and suspension:( I’m only 17 and got a straight pipe and lowering springs 😂

[@fearnobeer9077]

Focus on the engine , or everything else will sit on the side of the road

[@AM-le7eh]

So this will fix a P0300 misfire code and is this what causes a P0300 misfire code?

[@MotordyneG35]

Yes. P0300 means more than 1 cylinder is randomly misfiring. For example, p0303 means cylinder 3 is actually misfiring. It is best to replace it all, it is time once you get the code.

[@raulpilar6183]

@@MotordyneG35 i got the same code p0300 but i change the coils and the spark plugs and still have a misfire you thinks is a bad fuel injector

[@speedmaster001]

Can you please add a link on where you bought your coil packs and the price? Is that better than OEM? Thanks

[@MotordyneG35]

10:27

[@MotordyneG35]

Import direct is which brand from Oriley's. Cost me $0 to replace. Lifetime warranty. OEM doesn't offer any warranty and they both will only last 50,000 miles is why I never bought OEM. www.oreillyauto.com/detail/b/import-direct-ignition-4489/ignition---tune-up-16776/ignition-coils-19690/ignition-coil-12493/90c5da72ae86/import-direct-ignition-coil/230249/5732200/2005/infiniti/g35?q=Ignition+Coil&pos=1

[@bobbybrown9336]

U did great bro 😎

[@aale7777]

What brand ignition coil do you use ?

[@MotordyneG35]

Lifetime warranty from Orileys, if they ever fail you keep getting a new set for free. Most people don't keep a car longer than 3 or 5 years. Going on 14 years with the G with almost all of my parts from Oriley's because of the lifetime warranty. If it has a lifetime warranty I buy from Oriley's. No warranty, I use OEM. Import direct is the brand of the ignition coils.

[@aale7777]

@@MotordyneG35 ahh I was Looking at some Right now I was thinking of going with bwd but I'm planning on doing a tune on my car soon. I know you have a tune on your that's why I was curious on which brand you used

[@sirlucid4432]

@@MotordyneG35 How long have these Oreily coils lasted you before?

[@Robbievigil]

So which cylinder was the miss coming from?

[@MotordyneG35]

I've been through this before, I stopped it before the Misfire Random P0300 code came. It will go months with random stalls and dying before you get the code. After inspecting the plugs, multiple plugs were out of gap spec which is .043. Out of the 6 plugs, 2 were way off at .055 gap. Cylinder 6 and 3 I believe were the 2 way off the most. I had not actually gotten a misfire code yet, just the car dying at idle randomly. I even did my own idle relearn video and changed out my air filter hoping that was it, nope. I knew it was time again to do this job. Car runs perfect again now and much better.

[@RondosRaw]

Have a 06 g35 sedan getting a p0300 code changed all spark plugs and even got all brand new oem coil packs still getting misfire, anybody have any advice?

[@jonathanpadilla3149]

Did you ever figure it out? That’s where I’m sitting at right now with the same issue

[@RondosRaw]

@@jonathanpadilla3149 I ended up changing my catalytic converters and it fixed it for me.

[@GeraldK]

@@RondosRaw damn how much you pay? I probably gotta do the same.

[@RondosRaw]

@@GeraldK cats were about $400 for both put them on myself.

[@GeraldK]

@@RondosRaw Where are you get them from?

[@gudalawrence2028]

It would have been smarter to make the coil connector cables varying lengths pending on the position of each cylinder. That way you’ll not mix up the cables.

[@xandersavage2579]

Spent 2 hours doing this my hands are fucked 😂 very helpful video tho .!!

[@IcedTee89]

Good video for the most part, but some of the things said during the video raise a red flag for me...

[@3cinco76]

I have 07 g35 I recently left the car turned on but not running for 6 hours and then I noticed and turned it off battery died I recharged it because it was already dead on me already from siting and the gas meter stayed below the line we’re it shows it empty and I have pumped gas and unplugged the negative but it’s still hasn’t shown how much gas I have, now the service engine light turned on after I was in the car with the air on for 1 hour and I turned it off after the temperature went up and when I tried turning it on it started shaking read the code with obdII and it was p0300 code I’m going to change the spark plugs soon and clean the air filter has fresh oil change and berly gets driven it also had p0462 code any help id appreciate it

[@MotordyneG35]

Yeah the vq with a misfire shakes like a diesel truck. How many miles do you have? Check out my other video on bleeding the radiator. It only takes 1 time overheating to blow a head gasket. It will sound like a gunshot so you will know if you blow it.

[@3cinco76]

Motordyne G35 it’s berly about to hit 130k miles, it started shaking a little bit and stopped after a min but I’m going to do these steps and the radiator and clean the fuel pump and hopefully it drives smooth, I only purchased the spark plugs sound I get the plugs also ? And what is the best spark plugs and plugs to purchase ?

[@3cinco76]

Motordyne G35 you should do video on how to get disc for the navigation mine was broken and need replace it but I can’t find it

[@jaysonmason279]

@@MotordyneG35 oh no. Not a gunshot. SMH. My car ran hot but that didn’t happen. I hope i didn’t blow a gasket or nun 🙏🏿🙏🏿

[@Kyronsk8]

Is the hesitation you're speaking of when your try and floor it and the engine kinda does this whole pause thing before it finally begins to accelerate? I hate that and I'm not sure how to get rid of it.

[@463mafia]

that is normal. If you are just cruising and hammer it the car drops a gear or two and then goes, which is the lag you feel.

[@Kyronsk8]

said amir could I reduce our get rid of that?

[@Kyronsk8]

I don't mean when your driving and floor it, I mean from a stand still. Like I press the gas and it tries to go full throttle, then it stops for a second then restarts the acceleration process

[@463mafia]

Kyron could be that you’re losing traction it cuts off power then resume happens to me at time. Only way to stop this is get a DCT

[@Kyronsk8]

said amir ok I'll have to research what a dct is. Thanks

[@westsideray7324]

2006 Infiniti fx 45 v8 4.5

[@phineparcon8739]

What if both change and still missfire

[@MotordyneG35]

Dead fuel injector.

[@NFLYoungBoy223]

Hey anybody I have a 2007 Nissan Murano with 193,000 miles and I was just doing preventive maintenance by changing the valve covers because when I changed the spark plugs at 170,000 miles one spark plug was covered in oil the ceramic and where it sparks at and changed the 3 rear ignition coils but anyways this week I replaced the valve covers front and rear and that took me 4 days since it’s very cold in Chicago and it was snowing and so when I was working on the front one I had the front ignition coils in a drawer and they were kind of getting snowed on so I just wiped them off and closed the dresser to dry them and install them tomorrow so when I put the car back together I had a code that read P0081 then I looked around the engine and I just reconnected a harness and I reset the code then it was running fine for 30 seconds then it got to running rough again and got a code P0300 and wonder if it’s the front ignition coils but I replaced all the spark plugs at 170,000 miles and only the rear 3 ignition coils

[@drjimjam1112]

Drop down into the cylinder?? Coils only good for 50k?? What am I missing here, it’s April fools day or something??

[@dabestonly1687]

Nice work

[@NineOneOneFx]

Did this a few months ago. Passenger side is a BITCH!

[@stuwhyte479]

Alot of work just to replace the plugs isn't it.jesus christ!

[@RzVids]

Dislike solely for not showing the tightening sequence with torque wrench. I can’t find a video anywhere showing this.

[@sirchango2665]

RzVids just look up any forums and learn how to use a torque wrench. It does not get anymore complicated and if you don’t know how to use a torque wrench then you probably shouldn’t be working on your own car

[@Juniorcruz1234]

What brand are your coil packs?