Infiniti M35 - Front Wheel Bearing Replacement

It is important to note that the Infiniti M35 and M35x take a different wheel bearing (different part number). However, the installation will be the same for both vehicles. Let me know if you have any additional questions.
Thanks,
Alan

[@1mackzilla]

You did a good job with the video no matter what about the abs sensor or e brake comment. Its great people are taking the time to help out people that work hard for their money and try to save every way they can ! Thank you Bro !

[@PetesProjects0]

Thanks for creating this video. Just paid an Infiniti dealer a significant fee to do the same job. But I can see it going poorly if I had tried to do it myself.

[@kikatis3313]

Can you give me a idea of dealership cost? I know i cant do this!

[@don-cw1yz]

Just a couple of suggestions. Remove the ABS sensor before trying to remove the old bearing. Like the post just below mine says. If you don't you will break it. If you do Rock Auto sells them for about $100.00 vs Infiniti dealers at $300.00. Instead of a chisel b/w the splash shield to remove the old bearing back off the bolts that hold the bearing on. Have both front wheels off the ground. You can then use your chisel turned the opposite way to tap the bolts with a big hammer. The reason you have both wheels off the ground is so you can turn your wheel for easier access to those bolts to tap on them to get the old bearing out. Once out clean the the the hole with a brush /sandpaper and put no seize on the new bearing before installing. Then tighten the bolts, you can use the old ones to draw the bearing into place. Make sure you put the bearing in properly with the sensor hole in the same location as before. While you have the splash guard off you might as well sand it a bit and repaint with black rust paint. They rust a lot. That little f**king bolt that holds the sensor on the alloy section of the suspension has a nasty habit of breaking off. If you do break it this is what I did. Get an automatic centre hole punch and then drill out the old bolt. I tried taping the hole but the sensor hole is quite small and I tapped it too large. Plan B, I found a plastic fastener that fitted the hole and held the sensor on securely and that worked. No issues I put it in six months ago. I checked when I did my winter tire change over recently, holding solidly. Rock auto is also a good source for a good price on the bearing.

[@jamesofalltrades4359]

Damnnnnn shout out to my blue Infiniti crew. You and me might be the only 2 with the twilight blue color.

[@bksbullynyc]

I have that color too

[@RIF241]

I have this exact same car with this exact same problem right now. I was just priced over $800 at the dealership and around $500 at precision tune.

[@richphero106]

Thank you for this! Will see how the abs sensor looks like for my Fx

[@janwilliams178]

Great video this helped instill some confidence in me. Thanks

[@Darkeyce]

I really suggest you remove the ABS sensor BEFORE you pull the hub out. Snapping that sensor off will really change your outlook on the whole effort. I think it's a 10mm, just be aware that the bolt holding the sensor isn't super hard so be aware not to twist it off.

[@alanscartutorials6072]

Good point, Darkeyce. I know that the ABS sensor for the M35 is quite expensive, too. I shouldn't have overlooked this. Thanks, Alan

[@RooskiRooski0]

Great tutorial bro thank you

[@romancombs]

thank you Alen

[@matthewharding9690]

Thank you !! 🙏🏾

[@louislatour5973]

Thanks man

[@eddyrodriguez2021]

Very good everything but you have to remove the ABS sensor before you pull the old wheel bearing out because if you do not remove the ABS sensor it will be broken - I already know that because I broke one😮😱😄-

[@VLOGNOSIS]

Is 90 ft lbs the correct torque spec for the bolts?

[@karlsmith6832]

I had those same wheels on my BMW 7 series

[@demetriamajor7293]

I drive a 2006 Nissan Fuga 3.5 L. 4WD and was told it is equivalent to the Infiniti M35. I'm not sure now if it would be the wheel bearings for the M35 OR M35X that i need to purchase. Can you please help me?

[@theParticleGod]

M35X is the 4WD version. too late for you, but at least it might help someone else

[@awilliams-shieldwatch354]

the reason the brake pads and rotors were so hard to come off is due to the fact he has the e brake on

[@don-cw1yz]

The e brake only works on the rear wheels.

[@chriskeener9179]

Dude u talk 2 much