Install Multiple IP Cameras over Point to Point Wireless Bridge

[@ethiovisionary]

hy i am ayenew from ethiopia ,thank you ,great video clear and step by step instruction ,

[@Fastcabling]

Thanks and welcome

[@elfnetdesigns702]

All PoE switches are not alike and a thing you should also pay attention to closely because the radios will likely use PPoE (Passive Power over Ethernet : 12 - 40 VDC) where most cameras use the 48 - 57 VDC PoE Standards. A managed PoE switch typically can be set up to supply all the power to the devices per port BUT these switches can be quite expensive and require some experience setting up. The one we are using cost us right at $1100 USD Unmanaged (or Dumb) PoE switches like the one in this video are preset to supply power at a specific PoE standard so it will only supply power to devices compatible with the switch power output standards. Unmanaged switches are definitely cheaper because they lack the features to control what power goes where

[@Fastcabling]

You can try Ubiquit DC48V to DC24V passive convertor or the mananged POE switch you mentioned to select the standard (DC48V) or passive POE (DC24V) output. However, this kind of selection design take 1236 twisted pairs for standard POE and 4578 for passive PoE. Technically it break the IEEE802.3 standard. It doesn't work with latest IEEE802.3bt (aka PoE++), since all the 4 twisteds pairs must be occupied to send the standard PoE power.

[@hechur5106]

Is an internet/modem connection required to make this set up work? Or will it work with no internet?

[@Fastcabling]

Yes, it must be connected to your router or modem.

[@danielwelch5006]

Can i install a 3 wireless bridges togther to get connection at 3 different buildings?

[@Fastcabling]

We have newly launched a 5km outdoor wireless bridge that can configured for point-to-multipoint setups within a 30-degree beamwidth. If you have any questions, please feel free to contact us at [e-mail]! Product Link: www.fastcabling.com/product/5km-outdoor-wireless-bridges/

[@samcleophace8652]

Helo Is it possible to link up multiple distances nvr together and by which means??

[@Fastcabling]

If you're interested, we can also provide free solution design for our customers. All you need is to submit your request here: www.fastcabling.com/free-solution-design/

[@ricecctvsystem]

Thank you so much for this video

[@Fastcabling]

Thanks for your comment. If you're interested, please subscribed to our channel.

[@zfree]

​@@Fastcabling😮🎉🎉😢a I I I 1 am am

[@zfree]

​

[@eudraadiepinnock9008]

what is the bandwidth of the two wifi point to point?

[@Fastcabling]

The bandwidth will deteriorate as the distance increases. You can find more info here: www.fastcabling.com/product/1-pair-wireless-long-range-ethernet-bridge/

[@ianb2331]

Great videos. What solutions, if you have any now, to do a p2mp wireless setup, others have done it successfully. Would like to see a solution from Fastcabling.

[@Fastcabling]

Thank you! We're currently working on that. Please stay tuned!

[@iggymaluga6144]

HI, I would like to start by saying this is a very thorough step by step video, this has helped myself to understand this allot. My question is this, Do you have to setup the NVR at the source, which you have in the video, or could you simply remove the POE switch at the receiving end and use the NVR as the switch. I simply want the wireless bridge to connect to the internet so that you could use the mobile app to check in on the cameras from time to time.

[@Fastcabling]

Based on your question, it sounds like you want to use the NVR as a central hub for your IP cameras. You can connect the PoE switch to the NVR will act as a central recording and management device for the cameras. It will receive video feeds from the cameras and store the footage. If you simply want to monitor your cameras on your phone, you can just connect the NVR to your existing network and install a mobile app provided by the NVR manufacturer or a third-party app that supports your NVR model.

[@stephane-710]

Hello, thank you for the nice video. I just have a question. Why do you connect an external power supply to the bridge antennas? They are connected on both sides on the PoE line. On on side the NVR brings the power and on the other side the PoE switch will supply the bridge antenna. I’m wrong with my understanding? Thank you.

[@Fastcabling]

That's because this wireless bridge can only accept 12V DC and 24V passive PoE while our PoE switch delivers standard PoE power. For more information: www.fastcabling.com/product/1-pair-wireless-long-range-ethernet-bridge/

[@alfredotello1334]

I would like to connect 5 camaera to one access point being the nvr the receiver and camaras transmitters

[@Fastcabling]

You might need a PoE switch to aggregate video from these cameras before you upload it to the transmitter. Eventually, the receiver only need to work with single transmitter.

[@robklaver3206]

I've installed 3 IP cameras using your example. But i don't see 3 separate camera feeds in my monitor from Hikvision recorder, through the LAN port. Yet, when using any port (of the 8) I see 3 cameras switching in the same window. What physical IP address, of settings do I need to correct to view the 3 cams, coming from the wireless bridge? Thx

[@Fastcabling]

I think the problem is not the bridge. The birdge is transparent to the network. There is seperate VLAN running to negotiate the networking. If you saw the camera switching in same windows, i guess you have put receiver to one of PoE ports at the NVR. The NVR is designed to automatically make the link to any cameras to the PoE port. Since you have three IP address, so the NVR just keep changing the IP address. You might try the LAN port on the NVR instead of the POE port.

[@saptasetiyana8812]

can we use this bridge connection (point to point wireless bridge) install to moving equipment, juts like, i have 8 excavators and want to install 2 CCTV camera to each one of them, i have tried using modem, but in remote areas, 4G connection are not available, so i can't use modem to monitor my equiments.

[@Fastcabling]

It might not work. The wireless need to align. If the equipment is moving, then there is no guarantee it will stay in the same line.

[@kevinb6239]

Would I be able to use any type of cameras with your bridge?

[@Fastcabling]

The bridge supports a wide range of IP cameras, ensuring compatibility with various models and brands for a seamless and versatile setup. Check out the product info link for specific details on compatibility and features. www.fastcabling.com/product/1-pair-wireless-long-range-ethernet-bridge/

[@michaelvance9412]

Can a second bridge be installed like a camera to the poe switch? Then a second poe switch installed at the slave of the second bridge?

[@Fastcabling]

I assume you want to set two switches at both ends. Yes, the wireless bridge is transparent to the network. It turns TCP/IP to wireless signal.

[@michealjunior3434]

Can you plug in camera on the master side of the nvr

[@Fastcabling]

Yes, the wireless bridge is transparent to the network. You can add the IP devices at both ends.

[@asamir99]

Think you for explication very nice 👍

[@Fastcabling]

Glad to know it helps!

[@adamsalhassan805]

What ais the max distance from the ip to. Switch? Can it go up to 100m

[@Fastcabling]

It is 100 meters based on TCP/IP protocols. You will need some kind of extension solution to go beyond 328ft without breaking the protocol.

[@saptasetiyana8812]

cool.. thanks for sharing,,, but, i'd like to know if we can use this point to point wireless bridge if the slave bridge is installed on a moving objects, like excavators, cranes or forklift, and all these equipment are working on outdoor/open yard areas. is there any email or web that i can share my Topology CCTV design that i need?

[@Fastcabling]

Please email us at support@fastcabling or submit your inquiry here: www.fastcabling.com/free-solution-design/

[@JasonsLabVideos]

Um, if you don't buy cheap crappy product, you can to Point to multi pint just fine. Mikrotik has awesome products for ptmp.

[@bentheguru4986]

Aggreed, sadly, many security companies use this but don't have a clue about radio and throw shit up willy-nilly creating noise and interference for other networks.

[@JasonsLabVideos]

@@bentheguru4986 you use cheap china garbage, you get unreliable network. See it all the time. Not saying the ops stuff is garbage never used it or even see it on the market.

[@bentheguru4986]

@@JasonsLabVideos Just pushing their gear. Avertising YT channel

[@JasonsLabVideos]

@@bentheguru4986 alot of repeated videos too.

[@cyrusalarmservices5787]

i connected 4 IP cameras to one but only one picture shows up on the other side. looking at your video, i think i got my answer. i just have to go to the job site and apply it. nowhere in the manual mentioned anything about that on and off switch until you mentioned master and slave. switch. so, i'm going to turn the camera side switch off and se if it makes a difference. thank you for the hint.

[@Fastcabling]

Glad to know it helps :-) If you have more questions, please email us at [e-mail] or submit your inquiry here: www.fastcabling.com/free-solution-design/. Our engineer will get back to you as soon as possible.

[@a360ly]

❤

[@Fastcabling]

Glad you love it! If you're interested, please subscribe! More tutorials and case studies are coming soon!