Installation of TXG4 - RXG3 on bait boats

[@ЛеонидСавчук-д4в]

спасибо, очень помогло. Удачи.

[@krismichnak329]

Have list what need buying all electronics ?

[@RobertZovko]

if you are changing the existing electronics, then you only need the TXG4-RXG3 kit (it has everything: remote control, motherboard with GPS module, motor cables, antenna)

[@marcello7509]

I need your help, I have a question about the GPS module

[@RobertZovko]

how can I help you?

[@marcello7509]

Thank you for writing, can we do it in private?

[@RobertZovko]

[e-mail]@@marcello7509

[@marcello7509]

​@@RobertZovkook, I sent the message, thank you!

[@muratfisherman9769]

How to do it to the motherboard in the video. I have it too

[@RobertZovko]

from the motherboard, vcc goes to vcc of the GPS module, then GND goes to GND, TX goes to RX, RX goes to TX. You can find the module settings in my answers to others.

[@muratfisherman9769]

Thank you very much

[@jeanlucpiette9291]

Bonjour j aurai aimer changer le module gps comme le votre pourquoi y a t il que 4 fils de branchés Cordialement

[@marteenez1]

Hi, How did you connect back door to the main board? I see only two small motor outputs, but mine v18 boat has three small dc motors to open two side containers and back compartment.

[@RobertZovko]

connect the rear door to servo 1 or 2 greeting

[@marteenez1]

@@RobertZovko Thanks, but I have small dc motor instead, not a servo. When I connect dc motor to servo 1 or 2 it's always on, not assigned to any button of the pilot. How do you release servo 1 or 2 from pilot?

[@RobertZovko]

The V18 bait boat has a servo and not a motor on the back. It spins first in one direction and then in the other.? greeting

[@marteenez1]

@@RobertZovko As I sad, my revision of v18 has three 2-wire dc motors. I know that the other version has servo motor on the back, but not mine. If I power the board on, the back one connected to servo pins works all the time in rotary mode, same way as all dc motors works.

[@fishing_on_a_shoe_string]

Great video! I have learnt so much from your channel! I have installed the new equipment but I have a problem. Everything works as it should except I have no lights. Everything is connected as it should be. Do you have any ideas on how to solve or test the issue? Thanks for your time.

[@RobertZovko]

on the LED light connector, replace plus and minus (on this board they are reversed)

[@fishing_on_a_shoe_string]

Thank you for your quick response. I'll give it a go.

[@illNove]

Hi robert i want to ask did you zchanged anything on bk-280 module with u center because it comes with38400bps rate and did you stop any massages in u center like your last video can you explain mi how to do thank you very much 🙂🙂

[@RobertZovko]

@@illNove I didn't change anything. All settings are default.

[@illNove]

@@RobertZovko so you just welded it to board? Because in other answers you wrote 9600bps need to be

[@RobertZovko]

@@illNove Not for that motherboard

[@illNove]

@@RobertZovko thank you very much Robert for really fast answering to me. God bless you 💖

[@RobertZovko]

@illNove It cannot go "directly" to the motherboard, the pin layout is not the same.

[@sawomirjagieo4871]

Hello, I bought the TXG4-RX40G set and I don't know how to replace the GPS module? I thought I could just plug it in and it would work, but unfortunately it doesn't work, I don't know how to replace these modules, I probably need to re-solder something, could you post instructions on how to do it?

[@RobertZovko]

You do not need to change the GPS module.

[@sawomirjagieo4871]

but how to do it? Could you write a small instruction?@@RobertZovko

[@sawomirjagieo4871]

Does the GPS module need to be configured before installation or is it enough to connect it correctly?@@RobertZovko

[@RobertZovko]

I put the BK-280 and it doesn't need to be adjusted, I haven't tried other modules. baud rate: 9600 protocol: NMEA update rate: 5 Hz default 1 Hz SBAS on

[@sawomirjagieo4871]

OK thank you@@RobertZovko

[@pauliusberzinskas1810]

why did you change the gps module, you can tell me more?

[@RobertZovko]

I replaced the existing GPS module because the original one is of the M6 series, and I put the M9, which is more precise (

[@Dicibel]

@@RobertZovko Where did you order the GPS module? Link please?

[@RobertZovko]

​@@Dicibelwww.aliexpress.com/item/33030159409.html?spm=a2g0o.detail.pcDetailBottomMoreOtherSeller.3.7c6fO535O535pw&gps-id=pcDetailBottomMoreOtherSeller&scm=1007.40050.354490.0&scm_id=1007.40050.354490.0&scm-url=1007.40050.354490.0&pvid=f62a2132-3e70-4559-bbff-384cf37f8c46&_t=gps-id:pcDetailBottomMoreOtherSeller,scm-url:1007.40050.354490.0,pvid:f62a2132-3e70-4559-bbff-384cf37f8c46,tpp_buckets:668%232846%238111%231996&isseo=y&pdp_npi=4%40dis%21EUR%2110.87%218.70%21%21%2111.40%219.12%21%40211b600c17200067983308463e1b9d%2112000033295023263%21rec%21HR%21169046750%21&utparam-url=scene%3ApcDetailBottomMoreOtherSeller%7Cquery_from%3A

[@Dicibel]

@@RobertZovko the link is not working

[@RobertZovko]

@@Dicibel www.aliexpress.com/item/1005004405692761.html?spm=a2g0o.order_list.order_list_main.110.5ae61802fELoWf

[@johnfirst9233]

Имам лодка boatman actor2021 възможно ли е да се монтира такова управление

[@RobertZovko]

I don't know what engine is in them. According to the manufacturer's recommendation, it supports max 10A and 12V. These data are the ultimate limit at 12V current is about 8A. Most likely, coolers should be added to the drivers.

[@Dicibel]

Поменял тоже модуль gps и пропала связь между платой и пультом. Что может быть?

[@RobertZovko]

It depends on which module you put in and which motherboard it is. For some models, only their modules can be used.

[@Dicibel]

​@@RobertZovko а как привязать пульт к материнской плате по новой?

[@RobertZovko]

@@Dicibel which remote is it?

[@Dicibel]

​@@RobertZovko пульт как у вас в видео(TXG4) . Хочу сопоставить код по новой как это сделать

[@RobertZovko]

@@Dicibel if you replaced both the remote and the motherboard, watch the video at 1:22

[@КонстантинМалый-ю2з]

BK-280 возможно заменить на BE-280 . BN-280

[@RobertZovko]

I see no reason to change the module if you are going to put the same series (M8). I have not tried the M10 series.

[@pauliusberzinskas1810]

I also have a problem. I have a problem with the magnetic field norm H (20 -70 ), I have 120 uT, I tried everything but it doesn't decrease. Can you give me some advice?

[@RobertZovko]

you need to move the motherboard away from the magnet, for example the motor... to be sure, try everything before installation, if you still have too high readings, then the fault is on the motherboard

[@pauliusberzinskas1810]

I have one more problem. Maybe you had it too. after calibrating everything and setting the function to go home on autopilot, the ship will sail in the other direction and not to the point?

[@pauliusberzinskas1810]

should the arrow on the motherboard point to the front of the boat? and the gps module pointer to the main board? because the autopilot works the other way around??

[@RobertZovko]

Yes, the arrow points towards the front of the feeding boat. The GPS module is mounted on the motherboard and the module goes up, looking at the sky.

[@Antonio-tv1lv]

Hi, i ordered a v020 bait boat, do you think it is worth buying this kit to upgrade? Thank you

[@RobertZovko]

If you do not need one-handed control, there is no need to change the electronics while it is working.

[@Antonio-tv1lv]

@@RobertZovko Ah ok thanks, I don't need the one-handed controller but I would like to increase the precision of the GPS, given that many complain about poor GPS precision in these boats. Do you know if it is possible to increase the precision by perhaps just changing the GPS module with a more precise one? Do you have any to recommend? Thank you.

[@RobertZovko]

@@Antonio-tv1lv kzbin.info/www/bejne/eIrTh5msic1jiM0si=OOkzNWgXB0xNUWie

[@Antonio-tv1lv]

@@RobertZovko oh perfect thank you

[@muratfisherman9769]

Where does the GPS module connect? on motherboard please 🙏

[@emilandrello276]

Ciao come imposto scarico automatico?

[@RobertZovko]

1. save at least one position and home position 2. in the settings, set Automatic nest: YES 3. send to the position, everything else the bait boat do itself

[@emilandrello276]

​@@RobertZovkono non funziona

[@RobertZovko]

@@emilandrello276 it works, I use it in almost every fishing. I use 2 hoppers, but only one is activated automatically (poorly made program).

[@petrhutas7932]

do you have a casting deeper in your boat? if so, how do you deal with that antenna? what is the range?

[@RobertZovko]

kzbin.infoQCY1eNhAXGU?feature=share I fish at a maximum of 120 meters, so I tested it up to 150-160 meters and it works without problems, I didn't go further, but I believe it works at longer distances as well

[@anglermika3895]

Very nice