INSTALLING A HEADSET AND BOTTOM BRACKET ON YOUR BMX BIKE

For today's Tech-Thursdays I cover the basics for installing a bottom bracket and a headset on your bmx bike! Stevie Churchill makes an appearance and almost ruined the whole thing, haha just kidding.
But yea, hopefully this tutorial gives you guys all the necessary information and shortcuts you need to install a BB or headset on your bikes!
Please let me know in the comments about videos you want to see, other tutorials, and any other suggestions you guys might have!
Thank you everyone :)
Please make sure to subscribe to my channel:
/ alfredomancuso
The Come Up BMX
/ thecomeupbmxnet
No Jumper
/ thecomeuphowtos
www.ALFREDOMANC...
/ alfredomancuso
/ alfredomancuso
/ alfredo.mancuso
SNAPCHAT: ALFREDOMANCUSO

[@zactrawinski3927]

Beating on a 350 dollar frame is not the way to go. A piece of all thread or a long bolt with washers and a nut will do the job without chance of damaging frame. 4:36 made me cringe 4:45 shows damage to the paint on the chainstay from the wood I love your videos and hate to criticize

[@chrisparker8539]

Glad I found this comment!

[@TyIer0]

yeah i was like, bruh why would he do that😂

[@zactrawinski3927]

@@MidwestRainstorms They (and I) have a bearing press, was wondering why they didn't use it. The hammer is perfectly fine for rookies that do not take pride in their work, not a top notch shop. You my friend deserve to ride a dented frame with an out whack bottom bracket. Good luck with your hammer, if you dont have one you could try a rock.

[@t77snapshot]

@@zactrawinski3927 That little scratch on the cs was because he used a large piece of wood. I've been using the hammer/wood method for 25 years and not once has it ever damaged a chromoly frame. Heck I remember using rubber mallets to hammer on headset cups before bikes came integrated. Hey man if you're concerned about a scuff on your frame, then you will never progress. Ride safe guys!!!

[@magnetic0314]

important to note about sprocket spacing: your sprocket ideally should be dead in line with your driver, or as close to this as possible without the sprocket hitting the frame. shouldn't sacrifice chain allignment just for the sake of using up spacers when most crank-sets give you ample space for the spindle bolts to tighten without bottoming out

[@AlfredoMancuso]

solid point!

[@erodmedia5028]

How much more horsepower will a new bottom bracket add?

[@ben8596]

300

[@AlfredoMancuso]

420 +Ben

[@ben8596]

And a sweet blow off valve sound each time you stop pedalling

[@AlfredoMancuso]

6969 haha +enrique rodriguez

[@rickyrose1099]

420 dude obviously

[@andulasis6283]

its a nice tutorial but i honestly recommend to just build your own Bottombracket compression tool which costs about 5-10$ and is super simple. then you dont risk smashing anything and everything goes a lot smoother

[@bmxriderforlife1234]

heres a trick for installing a bb. just buy a loose ball 14mm axle for a front or rear hub. get a bunch of big washers that cover the bearing. grab a couple axle nuts. improvised bb tool. works really well. you can get the axles for free sometimes. other random bits of threaded rod will work. but a 14mm axle will work in any bmx crank and the length should be enough for pretty much any bb shell. worst case scenario you have to do one side at a time. thickest section in alot of those axles is like 17mm, and a lot of cranks use 22mm these days so yeah. even with 19mm cranks youve got room.

[@philaube]

Your tutorials are great! You should make a bike geometry 101 video

[@AlfredoMancuso]

That's a great idea! Writing that one down :D

[@TDJ-]

I will be watching this again while I install BB & headset on my new Cult frame & fork. Thanks Alfredo!

[@jonnyfoxmtb]

I'm starting to think you just carry Tony around and place him in different spots to make it seem like he's still alive.

[@richardhuerta4401]

Lmfao

[@sickofthis368]

I never put grease on my bearings and I have no trouble getting them out. Hell, I just replaced my BB recently and my only one was in for something like 6-8 years. Stevie is right, you don't need grease =P haha.

[@AlfredoMancuso]

Haha I'm just a cautious one but to each their own 😁+sickofthis368

[@sickofthis368]

Fair enough =D

[@bmxriderforlife1234]

depends where you live. if you have snow you need grease. salt fucks everything.

[@IsaacTheGuard]

Thanks man. Never installed a headset before. Great help.

[@Bozz_rb]

Great explanation thank youuu alf made it like its not even close to rocket science super well explained now my dads putting in mine

[@AlfredoMancuso]

If you need me to explain some rocket science, I can handle that as well ☺️ jk. Happy holidays man

[@ahigh]

Thanks for the details. Great video! Nice comic relief too with Mister "no-grease."

[@gmanloco2399]

Nice vid I been afraid to take my bike apart for maintenance is my first BMX bikes I found it in the trash I LOVE IT it needs a thorough cleaning and greasing. Thanks you. I Love your lazy fat cat.

[@wendellfrederickjr.4653]

✌🏾 bro, your very helpful for alot of info. But I'm confused on my headset. I've purchased an Odyssey headset put on everything as you said, everything is nice and sealed nothing moves, but when I do come down on the front, I hear a little rattle like somthing is loose, or could that be a normal sound, or i need my star nut knock in a little more... i put this headset on a legion 100 btw...

[@AlfredoMancuso]

There’s a lot of variables at play, but you could have your front hub loose, or those bearing could be messed up, your headset could be loose or damaged or your head tube could be ovalized so maybe it’s time to visit your local bike shop

[@oscarruiz7609]

I already know but a lot of people don't and they're going to love this video!!! keep the hard work up

[@AlfredoMancuso]

Thanks for that Oscar! +Oscar Ruiz

[@NextLevelTruth]

Tip to add would be, throw those bearings in the freezer for an hour or two. It slightly shrinks the metal and lets the bearings tap in easiest!

[@M4tth2w]

watched this video about 3 times, i watched a couple of months ago and about 2 days ago.. i then built my bike and put the cones on the wrong axel and had to find this video again aha.. iv'e built bikes before but accidently stuck the taller cone on the drive side.. it still worked but looked wrong lol anyway thanks for the videos Alfedo :)

[@seanhornchek6440]

you have a bike shop why do you guys not use bearings presses lol

[@vaIturi]

Sean Hornchek because not everyone has one laying around

[@bmxriderforlife1234]

you can make one out of an old 14mm looseball(or even sealed hub) axle and some washers and a couple axle nuts and a pair of wrenches. 30$ on the axle at most. axle nuts can be found easy. washers arent hard except for finding a big flat one to cover the bearing, but you can make those ones if you have a drill. its also lighter then a regular bb press, you can travel with it, its cheaper. and works just as well. any decent strength 14mm threaded rod should work as well. or anything smaller then 19mm and bigger then 10mm aka 3/8ths. hub axles are easy. just make sure it clears a 19mm bearing and you can install bb's for your friends and charge them 5$ as opposed to whatever a shop charges. or just let them use it.

[@tylerelson6042]

He's showing you how to at home without one. Cuz he's a boss

[@fentski9484]

I want to get oddysey thunderbolts which are 22mm and i have no idea if i have to have a certain frame. Do the frames have a certain size they take?

[@minecraftRULESAWESOM]

Fentski a frame will take any size bearing but it's the spindle and sprocket that require say 19,22mm

[@brianfonseca4283]

What kind of greaser did you use? Has to be an specific one or don’t matter?

[@AlfredoMancuso]

Doesn’t matter when it comes to brand, just try and get lithium, or very thin grease

[@rodneygreenway982]

How do I properly measure the length need for bottom bracket, spindle, etc. I have a 1999 Free agent speedway Jr. that I am trying to revive to give to my daughter, but forgot everything since I quit racing 20 years ago. Any help would be great. Thank you

[@nicknicky873]

How will you know the proper spacing alignment?

[@jordanjames5042]

Anyone help us

[@shawnzeeryp9296]

The spacers u want to place so your crank arms are the same distance from the frame

[@AvasTWCS]

Just passing by to say i love you (no homo tho) and i got them 180's and 360's dialed (bought a freecoaster), as always nice vid

[@AlfredoMancuso]

Ayyy love ya too!

[@illiteratethug3305]

Just spent half hour hammering BB into my new S&M BTM frame, then realised I forgot to put the spacer in between the bearings. There's no way the BB is coming out without smashing it to pieces. My BTM frame has a tapered BB, so there's no way the bearing cases can move in any further (there is still a *slight* lip and cannot get them in any further) so I should be fine without the spacer right? It can't move them in any further when I tighten up the compression bolt.

[@khue2626]

Question, Is there a reason why S&M doesn’t make the top of the frame’s head tube flush with the top of the sealed bearing?, Bottom of the head tube the sealed bearing sits in the head tube flush but on top The sealed bearing sticks out like 3 mm, Do they make a slimmer sealed bearing that will sit flush for the top integrated bearing race? Thanks

[@garrettramseyvlogs3235]

hey Alfredo quick question I had a harp 350.1 custom decked out and everything but it got stolen so now I got a hyper bike co bike for Christmas yeah its a Walmart bike with one piece cranks and a small sprocket but have already ordered stuff to make it better but back to what I was saying I can't find the kind of bottom bracket it is I've got a sealed mid 19 demolition at my place along with some mission three piece cranks but also the top of the frame doesn't have the bowl like good frames do so I'm pretty confused on what to do.

[@blaqkyellow]

I had a issue on bb bearing once to install it is the bearing supposed to feel smooth or feel a lil hard to move???

[@mattbealey9592]

when buying a new bottom bracket does it matter what size your cranks are?

[@favorites2154]

Can you do a video on installing dual bottom cranks and a dual chain (both sides L/R) I know it doesn't benefit but I Love the look..

[@coryschilpp2430]

an easier way to put in the bearing is with a rubber mallet instead of a block of wood and a regular hammer great video once again tho man loving the content you have been posting

[@AlfredoMancuso]

Yea that's a good alternative as well! Just figured I'd use a less conventional manner. Thank Cory! Appreciate ya! +Cory Schilpp

[@corrrupting]

so i have a mafia kush 2.0 i bought it second hand pretty cheap in good condition and im needing a new bottom bracket and stuff i have taken it apart but i dont have that mid spacer thing its a bit different so im needing a little help

[@AlfredoMancuso]

It’s not a super necessary piece

[@Reubenn]

Hey bro I am pretty much in the exact same situation as you. I brought a Mafia Kush 2 frame, handlebars, wheels and forks second hand and am trying to get all the parts to get it working again. It’s a lot more work than I expected but I am looking forward to completing it

[@frazzle657]

I want to swap down from 25 to 23 on my blackjack mafia bike. Mainly for wheelies. Will it be a good ratio? Rear driver is 10 I believe if not it's 9

[@miguelaganon6587]

If I buy a new complete bike with an integrated headset and sealed bottom bracket and I change the frame will I have to change the bottom bracket and headset and buy new ones or not?

[@gasware4681]

Damn really helped me learn about the BB on bikes. This was the last thing to learn about bmx's great vids.

[@kitekite1864]

Does my spindle have to fit snugly with my bottom bracket like yours does?

[@plfishing5076]

I know I’m late but isn’t it better and lower risk to pay up for the proper tool I am building a bike for the 1st myself (a verde Oxbridge frame) and am saving up to buy the right stuff

[@9000tastebuds]

Wow, thank you so much for giving a really clear tutorial, I just really love how you explain all the parts one by one, that's just really helpful, and make anything much easier for new builder. Anyway, is BB bearing and headset bearing comes in a different size for different BMX frame, or they had one universal size for all BMX frame. Once again, thank you very much dude, liked and subbed Edit: One more thing, do we had to find a correct size for spindle to make it able to get inside the BB bearing, or any spindle would just fit right in?

[@armata6530]

Just figured out how to join the notification squad, took me a while, but I'm in!

[@AlfredoMancuso]

My man!!

[@dahope5926]

Hey I have a question I started BMX riding a few months ago and I wanted to know when you buy a frame on any website does a bottom bracket come with the frame or do I have to buy it sepretly

[@WifeBeaterJuice]

you gotta get it separately most of time but always check the description first you might get one included, unlikely but still possible

[@RakeandRide315]

Got my bike back from the local shop, they left off the drive side cone nut. Is there a good reason?

[@joaquinjordan3221]

hi from Bolivia! you are the best alfredo

[@AlfredoMancuso]

Saludos a mis paisanos Bolivianos!

[@joaquinjordan3221]

+Alfredo Mancuso igualmente :)

[@logantittle]

Man I needed this video I have unsealed bearings and I got a bottom bracket so thanks for the vid

[@AlfredoMancuso]

That's great to hear Logan!! +Logan Tittle

[@bloodhawk1774]

First time watching. Instantly subscribed after you gave props to the cat.

[@AlfredoMancuso]

🙏🏻😂+Blood Hawk

[@bloodhawk1774]

Just bought my first bike last week. changing out my bottom bracket and sprocket tonight. I wish I got into BMX sooner!

[@Dansenara]

Does anyone know what's the width of a spanish bearing? I have a frame that uses euroBB and i had to switch to external bb cups to use something stronger than euro bearings. So I was wondering if a spanish bearing could fit inside those external cups. Thanks.

[@chrisfierro5018]

Question I'm new to bikes do you have to have that tubing in between the bottom bracket pieces

[@snuffy25454]

damn ! 9pm , that boy fredo working hard. preciate the video once again.

[@yungflavo822]

Iss 8 in Cali lmao

[@AlfredoMancuso]

Haha gotta think about them east coasters +rodrigo suayde

[@AlfredoMancuso]

Trying to get them going up earlier for my east coast homies!! Cheers bud! +snuffy25454

[@snuffy25454]

+Alfredo Mancuso awe shit son. East coast even later then ,because I'm in the dirty south (texas)

[@AlfredoMancuso]

That's true!! Dirty south lol +snuffy25454

[@Something141]

Do you have hammed in the headset bearings ?

[@gregsteele1921]

I know I’m so late, but how can you tell when the spacers in the bottom bracket are even or flush?

[@ululuskiappaski190]

So for the bottom bracket do I get a 19mm or 22mm my frame is a 20.75

[@iver6180]

this was actually really helpful thx

[@robertlund5694]

I sometimes find I need microspacers inside the bottom bracket with the big spacer because I tighten up everything and the middle spacer is too short and rattling around and the bearings are pinched but I think everything is becoming more standardised now.

[@AlfredoMancuso]

Yea for the most part, that shouldn't occur, but you don't reallllyyy need it

[@robertlund5694]

Most of the young dudes I know just throw all the spacers in the bin .stevie Churchill school of bike building! 😇

[@nelsonadrianrivera7096]

You explain so well

[@owen687]

does the headset cap have to sit flush on the front head tube?

[@favorites2154]

My bad great vid by the way, you guys are super chill, makes me want to be there...

[@ryanandrews9509]

This was such a great tutorial. You should make one on how to install cranks

[@AlfredoMancuso]

Thanks Ryan! Can do!

[@grxnt7841]

when installing cranks how many spacers should I use for the non drive side and drive side? Im getting a guard sprcoket and wanna make sure everything is even so that nothing gets messed up

[@AlfredoMancuso]

Hey Grant, you want to put as many spacers as it takes to get the cranks equally spaced. You can check this by installing the spacers, putting the crank arms on and putting your finger between the chainstay and the back of the crank arm

[@grxnt7841]

ok thanks for the help!

[@NOTHOTlanta]

The old "bang it with a hammer" method put some nice scratches on the frame :)

[@madetech]

Wow if i saw one of my employees use your techniques, i would fire them on the spot. Like your riding vids a lot and i like the way you explain tricks but i should give you a tutorial on good mechanical practices...

[@jimbeam3649]

no one asked joel

[@jrgomez7995]

Karen

[@thirdeyesurvivor3886]

Why would you fire them?? Why not teach them the right way to it and tell them to do it like that from then on? Seriously.

[@happychap2838]

you gunna try and do a gryo set up install? I always had trouble setting them up so i just run a straight cable lol

[@AlfredoMancuso]

yea! Saving that for a separate video!

[@happychap2838]

sick as fuck dude cant wait :)

[@AdrenalineJake]

stevie is right, you do not put grease on sealed bearings. it causes slippage on the non bearing side and can create unsmooth rotations.

[@AlfredoMancuso]

Personal preference! I've never had a bearing turn on me but I've had a seized bottom bracket before +Always Forgiven Jake

[@jessemiller1481]

yea man for sure I'm with Jake n Stevie iv been an auto tech/rider for years now and grease can cause caseings to slip see it all the time on older cars but that's no big issue the worst thing about grease is that it turns into grinding paste if your out riding street, trails and especially near beaches with wind and sand that's what ruins headsets and makes them noisy all the shit in the air sticking to all your sticky grease you've put on creating grinding paste! only thing needed is a light coat of something like wd40 on ur chain then wipe off excess to prevent accumulation of that dreaded grinding paste!, don't mean to sound like a no it all just sharing what i know!

[@robertlund5694]

+Jesse Miller your comments make sense but wd40 does nothing.. spit is as good.

[@jessemiller1481]

I know what you mean your right it is thin ,does wash away easily and can actually also leave unwanted waxy residue but its probably either use that or nothing for some riders that's why I said "something like wd40" me personally i soak my chain in solvent bath nd scrub with brush to flush out any crap, blow dry then reapply high quality dry lube (cheap poor quality brands leave behind wax residue) every so often, but honestly I could write a short novel on which lubes you should use for different conditions. it was more an example that heavy lubes aren't always better than thinner lubes hense the reason for writing "something like wd40" because its probably the only thin lube most people know of

[@robertlund5694]

+Jesse Miller wd40 managed to con the world into thinking it is an all in 1 solution. my father was in the coatings industry and he told me stories of the depth the wd40 company would go to to cripple competitor s and discredit anyone trying to challenge their product claims. some seedy goings on. it is and has always been only a moisture disperser. recently I have seen wd40 introduced other new more specific product s like lubes etc . kinda a admission that wd40 has never been an all in 1 solution. no , no wd40 on chains. I suspect most people use no lube of any kind . I just throw the chain on and use some average bike shop own brand dry lube to . I don't have the dedication to clean all the storage coatings off beforehand..😎

[@parkerh5209]

I don’t have a Tony cat do you think I can use yours

[@vicstorvejares1869]

Hello, my name is victor I have 15 and I'm from Argentina (I'm using google translator) wanted to ask as they have done for sponsor or something (I ask this question because my bike is very spoiled | Frame nearly went bankrupt to be accurate | and my economic situation is not very good to replace it and not want to stay without a bike since I love bmx

[@ianroddie357]

I have the same shadow headset and my dust cap raises a little bit more on one side than the other what could I do to fix this or is it normal?

[@AlfredoMancuso]

It might be ovalized and might need to be repared

[@ianroddie357]

Alfredo Mancuso my frame ovalized?

[@ianroddie357]

Alfredo Mancuso I have a brand new subrosa MR1 with a brand new shadow fork stem and headset

[@ianroddie357]

Alfredo Mancuso if it was ovalized how could it be repared?

[@5norlaxx]

i don't even ride box lmao but i love your videos! love ya man hopefully i get to meet you before school starts

[@AlfredoMancuso]

Damn, that means a lot! Come by the OSS Store anytime bud!

[@nolanblackall1210]

is the s&m dagger frame good Alfredo

[@jguti860]

do u have to use all the spacers

[@FreckleD718]

killed it alf and any suggestions where to get the Lucas oil lithium grease?

[@AlfredoMancuso]

Thanks David! I'd say Home Depot or an Auto parts store like Autozone. +David Griffin

[@dav9819]

What lubricant did he use? Can you send me a link to where I can buy it?

[@Onescratch]

I'm rebuilding mine soon glad I finally know what all those extra spacers are for smh I never used them

[@AlfredoMancuso]

Hahaha glad I could help then :) +David Lewis

[@tudorm6745]

For putting the bearings in you could also use a rubber mallet

[@AlfredoMancuso]

Also a good approach! +Tudor Does bmx

[@BLVCKBEATZ]

Frame looks sick love the color even if you and nate rock the same from now =D

[@AlfredoMancuso]

haha he Rocks a Stranger I have an S&M

[@BLVCKBEATZ]

just ment the color =D

[@jonathan1932]

What size are the bottom brackets u used

[@isaaczuniga6654]

What’s the name of the special adapter so my axel hold my sproket?

[@ethandenis5650]

so im a begginer and while i was learning 180's i shaddered my bb i dont know what size it is though

[@armata6530]

Are you going to do a whole bike build with your new dope S&M frame?

[@AlfredoMancuso]

Yea that drops tomorrow evening! +Cannon Hall

[@armata6530]

+Alfredo Mancuso sweet. Looking forward to it!

[@AlfredoMancuso]

😁🙏🏻+Cannon Hall

[@triimond5427]

Can you do a spokes tutorial/ how to build a wheel?

[@AlfredoMancuso]

Yea most def!

[@jake730]

the micro spacers are also for inside the frame your supposed to add micro spacers to the big one so its the correct lenth for your frame otherwise the bearings arnt being supported by the spacers so you may aswell not have one

[@AlfredoMancuso]

You're right! Solid point!

[@Jake-dh1jf]

What bmx bike should I get to star riding

[@AlfredoMancuso]

Stranger, Fit, Cult, or Subrosa all have great bikes!

[@nicknicky873]

How do you know what grease to use for different parts of the bike that is metal with metal?

[@Tom-gv7hc]

Use the greasy shit

[@person1867]

Can you do a tour of the oss store?

[@AlfredoMancuso]

Sure can :)

[@edwinandersson4783]

I have one question. When l tighten my cranks l can barely spin them. I can not do crankflips. What am l doing wrong?

[@AlfredoMancuso]

You're either over tightening or your bearings are shot.

[@herbois-et2uh]

hey need your help your bottom bracket small what size is that is it a 19mm? cause my bottom bracket look small like your what size uou using please lmk pm me please

[@AlfredoMancuso]

yea 19mm

[@matthewmaynard2002]

I grind on the right and my sprocket is on the right can I just flip my wheel around and my cranks and sprocket to the other side and will it still work fine?

[@AvasTWCS]

No, you'll probably have to get new cranks that rides on the left and another hub that rides on the left either, unless your hub has switchable pawls, you can't flip it.. You can try using the cranks on the other side but your pedals will get untightened within time and as you pedal time.. I made that switch a few days ago and had to buy new cranks that rides both sides and a LHD freecoaster

[@AlfredoMancuso]

Exactly!

[@matthewmaynard2002]

+avastinho thanks appreciate it!

[@deceivingthedeceiver]

Just the video I needed, thanks Alfredo. Also do most frames use a 22mm bottom bracket?

[@AlfredoMancuso]

Great to hear Sheldon! Most frame bottom bracket shells are MID, the 22mm is the inner diameter of the bearing for the crank spindle. I think 19mm is the most used spindle size and the new 24mm bearings are the least used. +Sheldon

[@sdfbisd]

Nah, it depends on your crank spindle size, if it's 19 mm then get a 19 mm bearing if it's 22 mm then get 22 mm.

[@AlfredoMancuso]

Exactly! +Javan Sam

[@rogeliovargas5548]

Where is your store located???

[@AlfredoMancuso]

It’s no longer around :(

[@tatertotbreakseverything7631]

my head tube dosent have those two rings, can I still install an integrated headset

[@isxiahm]

stevie was my favorite rider. but he smokes. so alf you and lz are right up there.

[@isxiahm]

+Jesus Rojo i dont dislike him im still a huge fan hees just not my favorite rider

[@DakaONER94]

cause he smokes? hows the high horse treating ya

[@isxiahm]

+DakaONER94 dontvreally understand that one bud

[@AlfredoMancuso]

🤔+Isaiah Mcphee

[@AlfredoMancuso]

Haha to each their own right? +DakaONER94

[@FreckleD718]

Good looks I'll check it out thanks!

[@AlfredoMancuso]

Anytime 😁+David Griffin

[@650juann2]

Is there a specific size

[@waterbell8112]

Yo is that S&M BTM frame?

[@JustFutureBlessUp]

Ratatatatata!😂🔥😎 boy slamming in w the upload

[@AlfredoMancuso]

BOOM!! My dude! +Just Future

[@xroouce2799]

how do i know how long i should order

[@TitanBeats]

my steertube has a bearing rider attached at the bottom of it

[@bikefaze7904]

yo thanks for the vid man I'm about to buy a bb and needed this lmao😂👊💯

[@AlfredoMancuso]

Nailed the timing! +bike faze

[@AlfredoMancuso]

Couldn't of timed it better then haha +bike faze

[@Ansemrp]

Yo thanks for these DIY vids, man.

[@AlfredoMancuso]

No prob! Glad you're enjoying them!

[@AlfredoMancuso]

Where's my notification squad at!

[@erodmedia5028]

Waasssaa!!😜

[@seanb7]

whats good

[@papersamurai88]

Pressing matter at hand!

[@billiam2486]

Yo!

[@staticsedan_3789]

right here

[@ryleychick3820]

great video! helped heaps bruv!

[@AlfredoMancuso]

Great to hear Ryley! +Ryley Chick

[@journeylara9710]

Great Video Thanks Alfredo Mancuso

[@AlfredoMancuso]

Hellya! Psyched you like it! +Dark13 Empire

[@amarucook7755]

Can you do a bike check after you build up your bike

[@AlfredoMancuso]

Drops tomorrow! +402 BMX Media

[@pianodanielnass]

Would you ever think of doing giveaways in the future?

[@AlfredoMancuso]

I'm giving away something off my bike tomorrow +CX3BMX