Thanks for watching the video! *Mark Fixes Stuff really needs your help* , so if you can chuck some change in the virtual hat to help support the channel at www.patreon.com/markfixesstuff I would be super appreciative and you can see your name in the video! If not then please enjoy the video anyway - every view, like and share counts! 😊
@Kak-jj9cq5 ай бұрын
Donde compro la bios
@MarkFixesStuff5 ай бұрын
@@Kak-jj9cq aqui www.ebay.co.uk/itm/256222364917
@DominicClifton4 жыл бұрын
To avoid lifting pads, use a low melting point temperature solder and put fresh solder on all of the pads. Add some fresh low melting point solder to the tip of your iron before you start wicking, this will help with thermal conductivity and will start the wicking process. Use flux as you did. But DO NOT press the wick into the board, just let it glide along the surface. Using a thinner width wick (1.5mm) on the small stuff helps as the solder will stay hot on the wick instead of all the heat dissipating into the giant wick which acts as a heat-sink. I do this and *never* lift pads. Also, if you are able to heat the entire package (chip) up and remove it in one go that's also good as then you don't exert any mechanical pressure onto the pads as no prising is needed. Avoid prising whenever possible.
@MarkFixesStuff4 жыл бұрын
Thanks for the tips Dominic. I really appreciate it. I’ll do that in the next video for sure!
@danielworley57562 жыл бұрын
Black screen isn't awkward, I like it
@FehNorth9 ай бұрын
I can solder but what you did here is beyond my level. Incredible work!
@MarkFixesStuff9 ай бұрын
Thank you so much. Actually I think SMD stuff is easier than through hole soldering but you need the right things so you are probably more than capable of this.
@FehNorth9 ай бұрын
@@MarkFixesStuff Thank you. After practicing more I'll chane the components in order to make my VA0 support GDEMU
@KingKrouch Жыл бұрын
You can get the devkit Sega Dreamcast boot sequence through a BIOS mod? Not gonna lie, that makes turning it on way more lively than the final boot sequence we ended up getting.
@3vi1J4 жыл бұрын
@1:09 [Picard voice]: There are FOUR screws.
@MarkFixesStuff4 жыл бұрын
MAKE IT SO! I NEED A NUMBER TWO!
@tonelander95344 жыл бұрын
I like how you got some solder on the hampton wick as well. Must have been a pain to remove.
@MarkFixesStuff4 жыл бұрын
😂😂😂
@underhandedrichard28963 жыл бұрын
I just recently looked into modding my dreamcast. Love the fact I found your channel
@MarkFixesStuff3 жыл бұрын
I love it too! Thanks for watching and taking the time to comment!
@tonelander95344 жыл бұрын
You must have arms like Popeye now Mark, due to all that speedy tool action.
@MarkFixesStuff4 жыл бұрын
Just one arm...
@rae912672 жыл бұрын
Oh...So the dreamcast really doesn't have a brain inside! THE COMMERCIALS LIED TO US
@BMR868 ай бұрын
that ebay link shows the shop is not around anymore
@MarkFixesStuff8 ай бұрын
Thank you. I’ve removed it now.
@MADFACEMANNN2 жыл бұрын
Hello! I bought a gd emu 5.15b clone but apparently my dreamcast VA1 (J) bios is protected. and prevents me from loading ROMS (cdi,gdi) from the emulator, sending me to the main menu. the question is, is it possible to replace the bios itself - shown in your video, and will there be conflicts with the GD EMU?
@MarkFixesStuff2 жыл бұрын
You can replace the BIOS. I did a video on it and the GDEMU doesn't care.
@MittensDoesThings19915 ай бұрын
16:44 How did you update the bios? Is there a file I need to find?
@MarkFixesStuff5 ай бұрын
@@MittensDoesThings1991 I bought mine programmed. I don’t have this Dreamcast any more because it was lost when my house burned down, but if I recall correctly I just replaced the original chip
@TheAnimeexpansion2 жыл бұрын
So I installed my kit and yeah no menu appears, not 100% sure what the next step is. I have a gdemu and ofc don't want to have any issues with it.
@MarkFixesStuff2 жыл бұрын
Have you double checked your connections?
@TheAnimeexpansion2 жыл бұрын
@@MarkFixesStuff yeah, thankfully got it working, although messed up due to the latest version not running with the gdemu whatsoever. So I'm attempting to get the old version back
@MarkFixesStuff2 жыл бұрын
@@TheAnimeexpansion oh no. I’m glad to hear you’ve made so progress though.
@TheAnimeexpansion2 жыл бұрын
@@MarkFixesStuff thanks, I appreciate that! Only roadblock now is my sd card reader isn't working. Got a very cheap one a little bit ago and the soldering on the legs is really shoddy!
@joesaiditstrue2 жыл бұрын
So would this mod be pointless for someone who has a launch japanese DC? Mine plays the Bootloader discs fine
@MarkFixesStuff2 жыл бұрын
it would just be cosmetic really.
@envisk8213 жыл бұрын
how do you update from v1.031 to v1.032? I see dreamshell comes with v1.031 already but trying to figure out how to load .32
@MarkFixesStuff3 жыл бұрын
Sorry. Missed this. I actually burned the update onto a CD-R and installed it from there. Hard to remember now though
@reminizАй бұрын
I just installed the new bios… now how do you use dreamshell???
@AndyVandercoy2 жыл бұрын
I just installed my bios and get a black screen sadly. I have a 1.6rev and there was a guide to solder to pin 9 of the ic503 from pin 44 of the bios chip. Also wired from pin one to the same you you soldered pin 1 of the bios chip to. Everything looked well and good, reflowed and continuity and all that. Flex cables fans and all that were secured. The system powers on, disk books and initializes, you here the beep and nothing on any screen I connected to. I got no answer from the ebay seller but it said free 3d dev. And I assumed I could just replace the chip without piggybacking. Any knowledge of where I might go from here?
@dogsauce198 ай бұрын
Was this for a VA0 Dreamcast?
@Rockythefishman4 жыл бұрын
Nice job fixing the pad 👍🏻
@MarkFixesStuff4 жыл бұрын
Thanks VV!
@RetromaniaGamers_643 жыл бұрын
it can boot games from the cd whit the bios custom ?
@MarkFixesStuff3 жыл бұрын
Yes!
@danielson95794 жыл бұрын
I remember that wrapper on lucozade bottles as well 😅
@MarkFixesStuff4 жыл бұрын
Crinkly. Used to buy it from the chemist hahah! Just sugar.
@MateoUrra-n1u9 ай бұрын
This mod is incompatible with the hdd retrodream mod?
@MarkFixesStuff9 ай бұрын
No idea. This console was lost in the fire. Sorry
@Flamelily-IT4 жыл бұрын
Absolute skills Mark. I wish I had your steady hands on my tools 😉
@MarkFixesStuff4 жыл бұрын
There's always 2021.
@ctrlaltrees4 жыл бұрын
Good length here Mark, and I was impressed with the depth that you managed to hit too. But I did come away somewhat unsatisfied... What happened to your infamous innuendos? I was sure you'd try to at least slip one in.
@MarkFixesStuff4 жыл бұрын
I have a NO FILTH policy.
@Jimfowler823 жыл бұрын
Haha the wrapping reminds me of lucozade too
@andresbudihardja3 жыл бұрын
how to do it with 88i6745 TFJ1
@ednairlanda2 жыл бұрын
Nice video mate! A question. With this bios , can I boot games from SD adapter without using the CD bootloader? My CD drive died, and Gdemu is quite expensive nowadays, and this looks quite easy to perform and very cheap.
@MarkFixesStuff2 жыл бұрын
No mate. Unfortunately. Although you could look out for a cheap cd drive instead - loads of people give them away for little
@sagiriizumi80794 жыл бұрын
I don't ever clean the pads. Just pop it down and heat it up. Otherwise you get issues like the pads coming off since they're old
@MarkFixesStuff4 жыл бұрын
Thanks. This might be the best way from now on. Thank you for watching and taking the time to comment. I really appreciate it.
@DoctorWhom3 жыл бұрын
@@MarkFixesStuff If you have trouble with not cleaning the pads, hopefully it makes it into a video. Louis Rossman rips off pads all the time, but he's repairing water damage.
@willl7934 жыл бұрын
So it just changes the menus and loading screen a little? 🙁 Still cool video I thought the chip would do more stuff though
@DecibelAlex4 жыл бұрын
it allows you to play region locked games and backups
@Colin_Ames4 жыл бұрын
Great job Mark. In the mid-50s I became ill with the Asian flu that hit the UK, and I drank an awful lot of Lucozade. Can you still buy it? I ask because I live in the US now, and obviously we don’t see it here.
@MarkFixesStuff4 жыл бұрын
Yes mate. It’s in loads of sugar free flavours now, playing off of the brand name but they original orange stuff is still on sale as a “sports drink”.
@Levin_Pilot_2463 жыл бұрын
Guys,I need your help, in the past, I used an Harbor Freight branded 1500 watt dual coil heat gun at maximum temperature like 1124 degree farenheit, but for some reason, I think I killed the old motherboard, because it didn't wanted to boot up, I got black screen, even though it was everything connected properly, no dirty connections at all. Possibly, because this heat gun was for other purposes, like stripping paint, and varnish, and not for electronics, next time, I will use it with the lowest temperature, at 572 degree farenheit instead, once I got a new motherboard
@computercomputer89223 жыл бұрын
Thermal pads that old should definitely be replaced.
@MarkFixesStuff3 жыл бұрын
Yeah. I need to do that.
@miikasuominen38454 жыл бұрын
Well. There are much smallers wicks, those are much better on those smaller pads. The real problem comes, if the pads have a large ground plane. For those, I would say use something to pre-heat the board. Like a "thermal pad" (don't know if that's a proper term in English)... And heat the board to something like 80 celsius... Though, it there are plastic connectors beneath, be careful. Those might not take the heat... As you said, on your case the pad was not connected to anything, so it really didn't matter. Though I would have also do the "repair", just like you did. Just for the looks of it... "Thicker" flux also tends to make everything easier, though it leaves more stuff on the board. Use IPA to clean them, always. "Running" flux leaves less markings, but doesn't do the job (on most cases) as good as the thicker one. Pick your poison, there is no "right choice". One works better to one and other for another. Train on not important things. You can never know before, if the board has good quality or if thr pads that fly out even with minimal heat and touch... Those can be repaired, though that will always make them look kess professional...
@MarkFixesStuff4 жыл бұрын
Thank you for sharing this. Reading your experiences really helps me on my SMD journey. I have a few thick fluxes to try as well. Brilliant tips! Please keep them coming.
@gregjarvis12324 жыл бұрын
Kit kats lucozade and gummie crew bear's on a day I have been hungry allday coincidence? I think not!.... Was eating a 6 pack of chicken wings while watching this
@MarkFixesStuff4 жыл бұрын
Don't type with your mouth full!
@DouglasTitchmarsh4 жыл бұрын
Great job again Mark👍
@MarkFixesStuff4 жыл бұрын
Thank you Duggie
@TheHimble4 жыл бұрын
Alcohol - the cause of, and solution to, all of life's problems.
@MarkFixesStuff4 жыл бұрын
Hmmmmmmmm Beeeeeeer!
@JacklapottTv3 жыл бұрын
What a genius discovery
@frankowalker46624 жыл бұрын
Nice work on the chip. I hate SMD. :)
@MarkFixesStuff4 жыл бұрын
Thanks Franko. I'm not keen myself, so I'm trying to expose myself a bit more.
@frankowalker46624 жыл бұрын
@@MarkFixesStuff Don't expose yourself too much, you might find you can't stop.
@MarkFixesStuff4 жыл бұрын
@@frankowalker4662 I can stop whenever I want... honest.
@yackyyam Жыл бұрын
I miss your innuendos lol
@fueledbyregret4 жыл бұрын
I’m quite partial to a multi finger treat.
@MarkFixesStuff4 жыл бұрын
Ditto. Do you have any openings that are yet to be filled?
@fueledbyregret4 жыл бұрын
@@MarkFixesStuff it’s a constant source of disappointment. Many ports, not enough DINs.
@MarkFixesStuff4 жыл бұрын
😂😂😂
@LewisWatt3 күн бұрын
You teared down the dreamcast just to mod it🤔🤔🤔🤔🤔
@Progressive.G3 ай бұрын
As WEIRD as this guy is I think he actually makes pretty good tutorials
@DecibelAlex4 жыл бұрын
careful when lifting the chip. It's very easy to ruin the PCB
@MarkFixesStuff4 жыл бұрын
Very true!
@wiggy89122 жыл бұрын
I'm laughing at all that work to replace a non-connected pad.
@MarkFixesStuff2 жыл бұрын
Yeah. My house burned down after this video and it was all destroyed anyway!
@tot_samy_vasya Жыл бұрын
Рукажопа нахера было снимать оплеткой лишний примой с контактов что бы оторвать площадку ! оно бы и так все припаялось
@stephenhargreaves90114 жыл бұрын
You do a lot of screwing on your channel.
@MarkFixesStuff4 жыл бұрын
It's a gift. I like keep my tool busy.
@Cloud95514 жыл бұрын
What was the point of this? Waste.
@MarkFixesStuff4 жыл бұрын
The point is to enable booting of backups and MIL discs on machines that don’t have that capability, such as later VA1 models that had the MIL booting loophole removed. I’m not sure what was wasted? 🤔