We installed the transmission that we rebuilt and ran into some trouble. Check out Casey and the boys over at Zuks Of Hazard KZbin channel youtube.com/@zuksofhazard?si=...
Пікірлер: 22
@Beana109 ай бұрын
KC will be the first official mechanic, with a degree, in the family. Proud of that young man. And yes, he is a chip off the old block.
@CTMadModz9 ай бұрын
He’s definitely got a gift and is a self motivator so he will go far
@scorpion05139 ай бұрын
Hell ya!!! I love being right! Thanks for the shout out!
@CTMadModz9 ай бұрын
I’m glad that’s all it was, thanks again
@scorpion05139 ай бұрын
@@CTMadModz me too, not a problem brother
@thebanjoman19639 ай бұрын
14:37 Lil' Dude is so 'Enthusiastic" about the rebuilt transmission. (Big YAWN) but it'll get him home!!! Thanks for sharing. I don't have any noises on my '92 trans but hopefully if I need to rebuild it parts will still be available.
@CTMadModz9 ай бұрын
Looks like Kevin has me scheduled to do a few tracker transmissions soon… I’ll have to do a step by step video for you 🤗
@thebanjoman19639 ай бұрын
@@CTMadModz my Samurai is 5sp. Sidekick Sport is Automatic..😁
@charlesgreathouse47989 ай бұрын
Yep, 2 chips, good job. Ronan looked like he approved😊
@CTMadModz9 ай бұрын
It doesn’t get done right unless Ronin is there 🤣
@MyAlaska129 ай бұрын
Glad it wasn't anything serious. Thanks!
@CTMadModz9 ай бұрын
Thanks man 🤘😎
@ZUKME9 ай бұрын
Nice! Almost brand new truck now ;)
@CTMadModz9 ай бұрын
Basically yeah, I need a new fuel tank like yours and I need to figure out what transfer case gear I need to get highway into speeds 🤣
@ZUKME9 ай бұрын
@@CTMadModz fuel tank was cake :) . When I get mine done i'm going to drive it to you :)
@CTMadModz9 ай бұрын
@@ZUKME bet!!!!!!!
@TheLifeOutdoorz6 ай бұрын
Nice channel, just subscribed!
@CTMadModz6 ай бұрын
Thanks for the sub, I look forward to seeing more of your samurai content too 🤗
@endurofurry9 ай бұрын
How do you get it past the pressure plate??? I have mine out and it was snug but did come out. now I cant seem to get it to go back up in. the bell housing hits on the pressure plate. what am I missing?
@CTMadModz9 ай бұрын
Go to the 7:00 minute mark and I tell you how to cut your cross member so you can install it easier
@endurofurry9 ай бұрын
@@CTMadModz I dont really want to cut it, it came out it should go back in. that's why I'm confused. worst comes to worse I will pull the motor forward. but I would really like to know why it wont fit as it did come out
@CTMadModz9 ай бұрын
@@endurofurry because your engine tilted down like 1/2”… if you unbolt your engine and move it forward that might work, you could also rock the front of your engine down and that Might work too… Casey over at Zuks of Hazzard KZbin channel just did a video explaining how to turn your trans a certain way to put it back in but mine is 16v swapped and I lost 1/2” from the adapter, so I cut my cross member. Good luck 👌