INSTALLING KEY IGNITION WITH VOLTMETER TO ELECTRIC SCOOTER [TAGALOG] PAANO MAGKABIT NG KEY IGNITION

BUY HERE ⤵️
SHOPEE: invol.co/cl6vc06
LAZADA: invol.co/cl73118
Need electric scooter spare parts in the Philippines? Check links below ⤵️⤵️⤵️
🧡 Shopee
shopee.ph/msko...
💙 Lazada
www.lazada.com...
🤍 Facebook Page
/ mskgenmer
RUSH ORDER? PWEDE YAN!!!
📍 Pickup San Pedro Laguna
📍 Lalamove
📍 Toktok
Kindly send us a message in FB Page for faster transaction, thank you! 👌🙏
TAGS: #mober #moberS10 #moberT10 #xtrack #panther #sealup #mobot #darknight #dd #ddva #dualtron #ecoride #inokim #kaabo #redline #rion #segway #tne #ucm #ultron #weped #xiaomi #m365 #xoom #xoomer #zero #evp #nami #maike #kuugo #lenovo #m2 #dyu #fiido #ecoride #romai #velicifero #kuickwheel #goboard #raze #genesis #viper #mijia #yume #eksph #electricscooter #tuovt #cst #donut #pleedo #owheels #moberX10 #S10 #S12 #T10 #X10

[@8474ggg]

Hello i have a e scooter kugoo m4 pro, I lost my key, can you help me? I can't switch on/off..

[@CarlitoFrancisco-s4o]

Sir gawa naman po kayo ng ignation key w volmeter throttle ang pag wiring Salamat po

[@reolarte5117]

Mabuti may nag content na ganito subra laki tuloy lalo sa walng repair shop malapit lugae nila tulad ko..nasave ng pera natutu pa thankz boss same un connection sa mober namn na walng key ignation.

[@subhashsitapure8619]

Will it work on e cycle

[@mskgenmer]

Yes it will!

[@noelalbais8233]

Sir yung scoter ko wala bolt mater

[@jhunecollado8256]

good day sir....kng sa terminal ng battery iconnect yng ignition switch with volt meter pwede po ba sir.....tnx

[@mskgenmer]

Malaki ang kuryente na nadaloy sa main cable ng battery, masusunog yung key ignition, pero kung voltmeter lang connect sa line ng battery, no problem

[@GieOnScoot]

Tanong boss.. ung scoot ko may key ignition at voltage meter sya from factory.. gusto ko tanggalin.. ano ang easiest way na pede ko gawen.. if i cut the three wires and put the positive and negative.. will it work?

[@mskgenmer]

Remove key ignition. Pagdikitin red-green or red-gray. Pag red-black, may masusunog 😉

[@toiletbowlteo8713]

Must I have the motor wires connected and connector for it to work? Cause it can't work for me or is the smtg wrong with my batt or controller?

[@mskgenmer]

All must be connected properly and correctly.

[@darkmorningsadventures6437]

Sir may scooter po ako pero thumb throttle po sya parehas lang din po ba silang 6 pins?

[@mskgenmer]

Iba iba po, depende sa brand ng controller at throttle talaga.

[@anchoykianne2158]

Electric Bicycle Thumb Throttle, 12V To 99V Real Time Display Bike Finger Throttle Accelerator Reliable Universal for 22.5mm Handlebars       

[@anchoykianne2158]

Display lang ba to bro...walang Accelerator

[@mskgenmer]

yang ginamit ko jan, yes voltage display lang and ON/OFF

[@trustpinoy9891]

Lods pwedi ko ba magawa yan sa Emove Roadrunner V2?

[@mskgenmer]

normally hanapin mo lang sa controller yung red wire to throttle

[@edisupono6813]

adding led light 12v from controller

[@mskgenmer]

Use buck converter, 36or48v to 12v..

[@KataladiTV]

Boss anong para saan nga ba ang volt meter sa Electric scooter ?😊

[@mskgenmer]

para malaman natin kung malapit na malow batt or full charge, para ma estimate naten gaano pa ilalayo ng takbo naten

[@Neil.khalifa]

Sir ganyan pwedi din po bang ganyan yung sa Xiaomi M365 ?

[@mskgenmer]

pwedeng pwede sir

[@jhunecollado8256]

sir sa ignition key with volt meter.....kng nawala susi saan jn sa mga wire ang pwede pg samahin para ma by pass yng ignition....tnx sir

[@musicandlyricsVLOGS]

ano problema sir ng moder md1 pag throttle mo di pa aandar, need pa itulak konti?

[@ronaldyee4258]

How to connect on a dual hub?

[@mskgenmer]

same technique apply here

[@_Hansing_]

Hello Bro, from Perth Australia ako and have an Emove Roadrunner. I have installed the same Voltmeter with Ignition on my scooter but problem is the LED is always on unless I take out the removal battery from the scooter. I followed this instructions on this link: kzbin.info/www/bejne/anuwdoaXqLqJpKc The only difference is that the ignition red wire from the video I followed is connected to the red wire to the controller, while the green wire from the ignition is connected to the red wire on the display. On your video is the opposite connection. Do you think po that this is the reason why the voltmeter LED is always on? and if I do connect this wiring like on your video what effects will it have on my scooter? Will it short my controller or display panel? Thank you in advance po and look forward to your feedback.

[@mskgenmer]

Yeah, that maybe the case. You can interchange, the red and the green, no harm. Just don't interchange the red to black or green to black.

[@_Hansing_]

Thank you sir for your quick response - much appreciated!

[@_Hansing_]

Hey mate, you're the best bro! I switched the red and green wires and the LED ight is now turning off when I switch the key off. Thank you very much for your expert suggestion! All the best pre and take care.

[@trustpinoy9891]

@@_Hansing_ I just got my Emove Roadrunner V2.. And I want to do exactly what you did with yours to have Key-Ignition in my Emove RR V2. If you dont mind Sending me How you did yours? And also Take Pictures so I can see what it actually Looks like. I don’t know much about these Electricity wires and stuff.. I just want Key-Ignition in my Emove RR v2 so Bad..

[@_Hansing_]

@@trustpinoy9891 sorry bro I had already sold my Roadrunner and bought an ebike.

[@calebsalenga2038]

Ask kulang po sana if ano ang possible na sira if laging naka on ang volt meter kahit naka off ang key ignition..

[@calebsalenga2038]

Gyro pro 60volts 21AH

[@mskgenmer]

baliktad po ang wiring, ng red/gray

[@calebsalenga2038]

@@mskgenmer wala naman po akong ginalaw sa wiring bigla nalang po syang nagka ganon..may effect po ba sa efficiency ng battery pag lagi naka open ang volt meter?

[@clma3780]

Hello, its possible to take the power source for my ebike light for 12v-60v system on the power source of the ignition? Or you think it can cause damage because to much electric flow (ampere) very thanks :)

[@mskgenmer]

no problem, ignition key normally works from 12V to 72V

[@chadvidad8110]

Sa joyor s5 po paano lagyan?

[@mskgenmer]

cut nyo lang po yung red wire between throttle and controller

[@Christian-f1f]

Lods pwedi poba lagay ang 48v controller na sinawave brand sa fiido q1,nasira ko kasi stock controller niya tapos nabili ko sinawave na 48v 18a and 380w

[@mskgenmer]

Pwede sir

[@georgeortal8747]

san bansa k kabayan???

[@mskgenmer]

pinas bro

[@pedrocruize3747]

Hell0 b0ss paan0 kung ang thr0ttle na nabili k0 ay 5 wires? kasi yung nakita k0 ngay0n ay 3 wires lang.paan0 b0ss mag install kapag 5 wires ang n0rmal ay red,black at green,per0 et0ng nabili k0 ay may s0brang 2 wires blue at yell0w, sana masag0t niy0 ,ang luma k0 p0ng thr0ttle ay QS-S4 ,marami p0ng salamat

[@mskgenmer]

dapat po sir, kung ano ung old throttle ninyo, ayun din po ang bibilin ninyo, kasi may compatibility po ang bawat throttle at controller

[@CRONY249]

ok hehehe sory sory

[@mskgenmer]

=)

[@raymartsablad5613]

Good day boss! naka bili po ako ng ganitong voltmeter with key ignition. ngayon yung mober x7 ko po yung key ignition nya naka connect sa odometer ng scooter ko, so kinabit ko nalang dun yung voltmeter with key ignition. ngayon po, di nagana yung voltmeter pag naka switch on sa key ignition, bumubukas po sya pag naka off sa key ignition. then simula nung kinabit ko yun, pag na abot po ako ng 40-42km/h bigla pong napitik and nababa ng 25-29km/h. kailangan po bang direktang naka connect to sa controller? Thank you in advance sa reply!

[@mskgenmer]

i diriretso nio na lang po sa controller, cut throttle connection as per video po

[@joeymoreno1832]

Idol ung ebike q kasi key ignation na xa na my kasamang lcd battery ma bar lng now gusto q sana lagyan ng voltmeter sa red and black qlng ba ikakabit sa controler nya pwede q tap nlng dun sa stock meter nya na bar lng with throtole

[@mskgenmer]

hindi sir, dapat i break mo yung live wire para magkapurpose yung key ignition

[@kabradpete3078]

Salamat Bro. Nkabitan ko na din scoot ko. 👍 Addition lng bro, pwede ba q mag direct connection additional ng 12v lights sa stop light at break light ng scoot MR 100?

[@mskgenmer]

Hindi sir. Gamit ka step down po.

[@carlosmiguel2810]

bro gawa k ng video about key ignition para sa fiido qis controller

[@mskgenmer]

may ready port na po ang Q1 at Q1S for key iginition sir, pero sige gawan ko po. salamat

[@JCL-fq9ur]

Ok ok ok

[@mskgenmer]

thanks

[@technician1016]

Hai sir have a good day po. pwedi po ba yan sa MI na scooter?

[@mskgenmer]

pwedeng pwede po

[@nidaesteda1042]

Magagawa paba yung na drian yung batery nya boss nadrian kasi baterry ko dina cha chages

[@mskgenmer]

magagawa pa po, gugulatin lang, alam ng mga technician yang term na yan

[@adamafable3236]

Ito yong maliwanag may actual yong iba d Rin maintindihan Binabasa lang din ano nakalagay di maexplain Ng ayos 😊

[@mskgenmer]

Salamat po.

[@jeffreyferrerofficial832]

Boss ginaya q yang tutorial mo pero ndi gumana ung controller ko😢

[@mskgenmer]

Baka may dedicated port for key ignition na yung controller ninyo? Or baka baliktad yung red/gray ng key ignition? Message nio kami sa page

[@jaypeesantillan9288]

good morning sir. tanong lang po sana, pwede po bang mabasa ng ulan itong finger throttle?

[@mskgenmer]

bawal po

[@bikersabukid]

Sir, ngbebenta po kayo nung wire connector na tinap nyo sa throttle wirings?

[@mskgenmer]

Hindi po sir. Throttle wire lang po invol.co/cl56h0s. Pero marami po nagbebenta nyan sa shopee/lazada.

[@spylance46]

San po sya na controller pwdee ilagay? sa rear controller poba?

[@mskgenmer]

kung dual hub ka, dun mo ilagay sa controller na naka konek sa throttle.

[@carlosmiguel2810]

nxt video nmn battery range extension

[@mskgenmer]

Sige sir noted po, gawa tayo info about it ,

[@walterwhite2165]

Sir gawa din po kayo video wirings ng dual motor switch

[@mskgenmer]

yes sir, gagawa ako dual motor soon :)

[@carlosmiguel2810]

awesome salamat very imformative from ksa

[@mskgenmer]

Salamat din po from san pedro laguna 😊😊😊

[@carlosmiguel2810]

@@mskgenmer taga dasma lng ako hehehhe...but dto ako sa ksa

[@marklouiechan9158]

Hello sir sana makagawa po kayo ng video for error 14 thanks

[@mskgenmer]

anong brand ng throttle sir?

[@marklouiechan9158]

Generic throttle lng po sir and yung display board po thanks

[@dayoffdiy3161]

Matagal na akung naghahanap ng ganitung content. Salamat paps

[@mskgenmer]

welcome sir! :)

[@bobzmarley8754]

Ser kaya mo rin ba gumawa or kaya ba lagyan ng key ignition voltmeter ang controller na wlng display/dashboard?

[@mskgenmer]

Kaya. Normally yung mga no dashboard, mero yan kill switch, dun mo ilalagay yung key ignition.

[@bobzmarley8754]

Ooh mron nga sya kill switch or ignition kso 2 wire lng yun mron doon so paano ko sya mlalagyan ng key ignition voltmeter with 3 wires ser?

[@mskgenmer]

Kapag bumili ka ng new key ignition with voltmeter. Yung black wire lagay mo sa ground.

[@spylance46]

Ang JP controller sir meron bang port para sa key ignition?

[@mskgenmer]

May J&P video ako rito sir,

[@mskgenmer]

meron po sir

[@JCL-fq9ur]

1 million ok

[@mskgenmer]

thanks

[@willycortez3732]

Sir paano connection nyan para naman sa xiaomi scooter?

[@mskgenmer]

Cut mo lang yung red wire from dashboard to controller. Dun mo isingit yung key ignition

[@willycortez3732]

@@mskgenmer natry ko na yung ganun sir. Pero 5v lang lumilitaw sa display ng key ignition switch. Un sanang real battery capacity. May nagsasabing nagmodify sila. Yung tatluhang wite ginawa nilang apat. Then sa ilalim sila kumuha ng linya. Nilagyan ng relay

[@mskgenmer]

@@willycortez3732 tama yun sir, 5V lang makukuha mo sa voltmeter kapag ganitong wiring ginawa mo. tama rin yung relay, tas yung source mo patakbo ka ng wire sa controller, tapos yung voltmeter sa key ignition dun mo konek yung galing sa baba. gawa ako vid soon.